The banded spherulites of iPP induced by pressure vibration injection molding

Isotactic polypropylene(i PP) samples obtained by pressure vibration injection molding(PVIM) and conventional injection molding(CIM) were studied by polarized-light microscopy(PLM), respectively. It was found that the alternating bright and dark banded spherulites were generated in the transitional region of PVIM parts. It is the first time that the banded spherulites of isotactic polypropylene were observed in polymer processing. What's more, the banded spherulites were proved to be constituted of ?-form crystal by hot stage polarized-light microscopy(HT-PLM) and wide angle X-ray diffraction(WAXD). Morphology of the banded spherulites was also studied by scaning electronical microscopy(SEM).     

Characterisation and coagulation performance of polysilicate-ferric-zinc

A new type of coagulant, polysilicate-ferric-zinc (PSFZn) with different Fe/Zn molar ratios, was synthesised using water glass (industrial grade, w(SiO₂) = 21 mass %, ρ = 1.34 × 10³ kg m^?3, modulus = 3.2), FeSO₄ · 7H₂O, ZnSO₄, and NaClO₃ by way of co-polymerisation in the same (Fe + Zn)/Si molar ratio based on polysilicate-ferric (PSF). The effect of the Fe/Zn molar ratios on the morphology and structure was systematically investigated using scanning electron microscopy (SEM), Fourier transform infrared spectroscopy (FTIR), and X-ray diffraction (XRD) analysis. Three samples, namely PSFZn4, PSFZn1, and PSFZn0.25, represented Fe/Zn molar ratios of 4, 1, and 0.25, respectively, and were selected for a comparative study while a constant (Fe + Zn)/Si molar ratio equal to 1 was maintained. Accordingly, PSFZn was found to be a complex compound rather than a simple mixture of raw materials. With the decrease in Fe/Zn, a great change occurred in the surface morphology, from a tetrahedral cluster structure to a lamellar structure. The Fe—O and Fe—O—Si bonds were gradually replaced by Zn—O and Zn—O—Si. However, the crystalline peaks were more obvious with the increase in the number of zinc ions; hence the new polymer would be formed from iron, zinc, and polysilicate. In addition, the coagulation performance of PSFZn was investigated using a surface water sample. PSFZn4 exhibited a better coagulation performance than the other PSFZn coagulants. Additionally, the trends in changes in pH with different coagulation times after adding PSFZn were studied relative to PSF and FS. The replacement of zinc ions with iron ions could effectively counter the rapid decrease in pH. The effect of settling time on the coagulation efficiency was also investigated. PSFZn4 exhibited a better settlement performance than PSF and poly aluminium chloride (PAC). Hence, the partial substitution of zinc salt with iron salt not only addresses the inadequacies of iron salt but also improves the coagulation efficiency of zinc salt in water treatment.     

杂多酸离子液体催化燃油萃取氧化脱硫性能研究

本文首次将一系列含有不同酸性咪唑阳离子和不同杂多酸阴离子的杂多酸离子液体[C4mim]3PW12O40、[COOH-Cmim] 3PW12O40、[SO3H-C3mim]3PW12O40、[SO3H-C3mim]3PMo12O40和[SO3H-C3mim]4 SiW12O40作为催化剂,乙腈为萃取剂,H2O2为氧化剂,用于催化含二苯并噻吩、苯并噻吩及噻吩模型油的萃取氧化脱硫研究中.实验结果显示,杂多酸离子液体催化燃油脱硫性能不仅与阳离子的酸性强弱有关,而且与阴离子结构密切相关.阳离子的催化活性顺序为:[SO3H-C3mim]+＞[COOH-Cmim]+＞[C4mim]+;阴离子的催化活性顺序为PW12O403-＞ PMo12O403-＞ SiW12O404-.其中[SO3H-C3 mim]3 PW12O40催化活性最高,在60℃反应40min的条件下,二苯并噻吩的转化率约为100％,催化不同硫化物的转化率为:二苯并噻吩＞苯并噻吩＞噻吩.此外,该杂多酸离子液体循环使用5次催化活性仅略有下降.     

Total Syntheses of (−)‐Isoschizogamine and (−)‐2‐Hydroxyisoschizogamine

Total syntheses of (?)‐isoschizogamine and (?)‐2‐hydroxyisoschizogamine are described. The synthesis employs two asymmetric Michael additions to establish chiral centers at C7 and the quaternary carbon C20. Regioselective reduction of the methylthioiminium cation rather than the enamine generates an isoschizogamine‐type pentacyclic skeleton. Acidic hydrolysis of the isoschizogamine‐type intermediate in the absence of oxygen provides natural (?)‐isoschizogamine. Conducting the reaction in the presence of oxygen leads to a multistep oxidative hydrolysis cascade that affords unnatural (?)‐2‐hydroxyisoschizogamine.     

嵌段共聚物相容剂对聚合物共混体系力学性能影响的连续介观模拟

结合介观动力学方法和三维弹簧格子模型, 研究了嵌段共聚物相容剂对相容性较差的聚合物二元共混体系力学性能的影响. 在适当范围内不断增加嵌段共聚物相容剂的用量, 研究了相容剂含量对体系杨氏模数及拉伸强度的影响, 同时也对不同体系材料的破碎位点进行了分析. 结果表明, 未加入相容剂的二元共混体系在拉伸模拟中表现出较低的拉伸强度, 而适量添加相容剂可以显著提升材料的拉伸强度, 随着相容剂含量的增加, 共混体系的破碎位点会发生转移并最终改善材料的整体性能. 而相容剂的加入对体系杨氏模数的影响较小. 该连续模拟方法为关联聚合物复合体系的微观结构和宏观力学性能提供了一条高效的途径.     

Ti掺杂苯基与乙基桥连的有序介孔有机硅的制备及其催化环己烯氧化反应

分别采用1,4-(双乙氧基硅烷)苯(1,4-BTEB)和1,2-三乙氧基硅基乙烷(1,2-BTESE)作为有机硅源,正硅酸乙酯(TEOS)为无机硅源,钛酸四丁酯(TBOT)为钛源,以Pluronic EO20PO70EO20(P123)为模板剂在酸性环境下水热合成制备了Ti掺杂的有机-无机有序介孔有机硅材料Ti-SBA-15-ben和Ti-SBA-15-et.同时,在合成过程中加入H2O2作为配合剂调节钛源水解速度,制备得到Ti-SBA-15-ben-H和Ti-SBA-15-et-H.采用FT-IR、DR UV-Vis、N2物理吸附、XRD、TG-DSC、TEM等方法对制备的样品进行了表征.结果表明:合成过程中加入H2O2制备的苯基桥连有机硅杂化材料具有较好的疏水性能,其骨架中活性4价位钛含量高,结构有序性最好.在以叔丁基过氧化氢(TBHP)为氧源的环己烯氧化反应中对制备的催化材料进行了对比评价,结果表明:Ti-SBA-15-ben-H表现出最高的催化活性,其催化的反应以环氧化产物为主,环己烯的转化率为26.9%,环氧选择性为32.8%,T i-SBA-15-et催化的反应以烯丙位氧化产物2-环己烯-1-酮为主,环己烯的转化率为8.5%,2-环己烯-1-酮选择性为41.2%.     

简便的双环化反应合成3,7-二甲基-4a,16-二羟基-1H-苯并[5,6]茚并[2,1-1]氧杂蒽-1,9-二酮化合物及其结构表征

标题化合物C26H26O5以2,3-萘二甲醛和5-甲基-1,3-环己二酮为原料,在醋酸溶剂中,室温下经搅拌多组分一锅法合成得到.其结构通过单晶X-射线衍射法确定,晶体属单斜晶系,空间群P21,相对分子质量Mr=418.47,晶胞参数a=0.990 04(8) nm,b=1.090 98(9)nm,c=1.042 46(11) nm,V=1.087 53(17) nm3,Z=2,晶胞密度Dc=1.278 g/cm3,吸收系数μ=0.088mm-1,单胞中电子的数目F(000) =444.晶体结构用直接法解出,经全矩阵最小二乘法对原子参数进行修正,最终的偏离因子为R1 =0.053 3,wR2=0.129 3.在晶体结构中新形成的吡喃环为半椅式构象,而茚中五元环则为信封式构象.     

Simultaneous determination of naphazoline and pyridoxine in eye drops using excitation–emission matrix fluorescence coupled with second-order calibration method based on alternating trilinear decomposition algorithm

A novel method is developed for the direct determination of naphazoline hydrochloride(NAP) and pyridoxine hydrochloride(VB6) in commercial eye drops. By using excitation–emission matrix(EEM)fluorescence coupled with second-order calibration method based on the alternating trilinear decomposition(ATLD) algorithm, the proposed approach can achieve quantitative analysis successfully even in the presence of unknown and uncalibrated interferences. The method shows good linearity for NAP and VB6 with correlation coefficients greater than 0.99. The results were in good agreement with the labeled contents. To further confirm the feasibility and reliability of the proposed method, the same batch samples were analyzed by multiple reaction monitoring(MRM) based on LC–MS/MS method.T-test demonstrated that there are no significant differences between the prediction results of the two methods. The satisfactory results obtained in this work indicate that the use of the second-order calibration method coupled with the EEM is a promising tool for industrial quality control and pharmaceutical analysis due to its advantages of high sensitivity, low-cost and simple implementation.     

Particulate capillary precolumns with double-end polymer monolithic frits for on-line peptide trapping and preconcentration

In this work,a novel kind of particulate capillary precolumns with double-end polymer monolithic frits has been developed.Firstly,the polymer monolithic frit at one end was prepared via photo-initiated polymerization of a mixture of lauryl methacrylate and ethyleneglycol dimethacrylate with 1-propanol and 1,4-butanediol as porogens and 2,2-dimethoxy-2-phenylacetophenone as a photo-initiator in UV transparent coating capillary(100 μm i.d.).Subsequently,C18 particles(5 μm,100 A) were packed into the capillary,and sealed with the polymer monolithic frit at another end.To prevent the reaction of monomers and C18 particles,the packed C18 particles were masked during UV exposure.The loading capacity of such a precolumn was determined to be about 9 μg by frontal analysis with a synthetic peptide APGDR1 YVHPF as a model sample.Furthermore,two parallel precolumns were incorporated into a two-dimensional nano-liquid chromatography(2D nano-LC) system with dual capillary trap columns for peptide trapping and concentration.Compared to 2D nano-LC system with a single trap column,such two dimensional separations could be operated simultaneously to improve the analysis throughput.All these results demonstrated that such capillary precolumns with double frits would be promising for high-throughput proteome analysis.