赶酸对微波消解-氢化物发生-原子荧光法测定谷物中砷元素的影响

在利用氢化物发生-原子荧光分测定谷物类样品中砷元素时,硫脲-抗坏血酸的还原效果会受到硝酸含量的影响,试液中硝酸含量过高,会与硫脲-抗坏血酸溶液发生氧化还原反应,降低其还原效率。本研究通过对赶酸时间和赶酸温度进行试验,获得最佳的赶酸条件,结合微波消解技术,利用氢化物发生-原子荧光光谱法测定谷物中的微量砷,结果表明,谷物中砷浓度与荧光强度呈线性关系,线性方程为 y=0.0028x-0.1728,线性相关系数R2=0.9993,检出限为1.72ng/g。 通过对9份样品进行检测,其相对标准偏差RSD在4.32-7.59%之间,其准确度相对误差RE均小于±6.50%。经多次检测证实该方法较稳定,可用于谷物类样品中砷元素的快速测定。     

沉淀铁催化剂在F-T合成中的研究与应用进展

F-T合成是煤间接液化的关键工艺步骤,选择鼓泡浆态床反应器和廉价高效的铁催化剂是实现低氢碳比的煤基合成气转化的最为现实有效的产业化途径.本文对近年来国内外F-T合成技术发展进行了评述,着重介绍了用于浆态床反应器的沉淀铁催化剂的制备化学、成型方法、活性相组成、预处理条件及诸因素对F-T合成性能与工艺的影响,指出并展望了该类催化剂今后腞&D趋势与方向.     

Aβ蛋白分泌酶抑制剂研究进展

Aβ蛋白是淀粉样前体蛋白的代谢产物,它在脑组织中含量的异常增加可能是诱发AD的主要因素.应用分泌酶抑制剂可有效减少Aβ的生成,缓解患者症状.本文综述了其中的β分泌酶抑制剂的研究进展.     

混凝土板爆破作用数值分析

混凝土板是爆破拆除经常遇到的爆破对象,是建筑物的基本构件．爆炸应力波峰值随距离衰减是工程爆破参数设计的理论依据之一．通过数值计算,研究爆炸应力波峰值随距离的衰减规律．研究结果表明,与无限混凝土介质相比,爆炸应力波峰值在混凝土板中衰减较快．应力波峰值的衰减指数随装药量增大而减小,衰减指数的变化率也随装药量的增大而减小．     

一种岩石概率型本构及其应用

在岩石材料非均匀特性的基础上,建立了弹塑性概率材料本构．认为材料单元的切线模量与破坏强度都是服从二参数Weibull分布的随机量,通过用户材料子程序将该本构导入到LS—DYNA3D中,推导了程序流程,分析了导入过程中的关键技术．算例验证表明,应用该本构模拟得出的现象与实验观测完全一致,这是确定性本构无法实现的．     

Monitoring single Au38 nanocluster reactions via electrochemiluminescence

Herein, we report for the first time single Au₃₈ nanocluster reaction events of highly efficient electrochemiluminescence (ECL) with tri-n-propylamine radicals as a reductive co-reactant at the surface of an ultramicroelectrode (UME). The statistical analyses of individual reactions confirm stochastic single ones influenced by the applied potential.

Herein, we report for the first time single Au₃₈ nanocluster reaction events of highly efficient electrochemiluminescence (ECL) with tri-n-propylamine radicals as a reductive co-reactant at the surface of a Pt ultramicroelectrode (UME).

Single entity measurements have been introduced by Bard and Wightman based on the collisions/reactions of individual nanoparticles and molecules at an ultramicroelectrode (UME).^1–9 Since then, the field of single entity electrochemistry has gradually attracted several research groups and has become a frontier field of nanoelectrochemistry and electroanalytical chemistry.^8,10–14 For instance, it has been shown that the chemistry of the electrode surface plays an important role in the collision/reaction events and the kinetics of reaction processes.^15–21 Dasari et al. reported that hydrazine oxidation and proton reduction can be detected using single Pt nanoparticles on the surface of a mercury or bismuth modified Pt UME, and the material of the electrode was found to affect the shape of current–time transients.^22,23 Fast scan cyclic voltammetry provides better chemical information about transient electrode–nanoparticle interactions, which is otherwise difficult to obtain with constant-potential techniques.²⁴ There are only a few reports on photoelectrochemical systems including semiconductor nanoparticles designed to detect single nanoparticles in the course of photocatalysis processes.^25–28 More importantly, owing to the nature of stochastic processes of single entity reactions, statistical analyses have shown substantial influences on the understanding of the underlying processes.Electrochemiluminescence or electrogenerated chemiluminescence (ECL),²⁹ as a background-free technique,^30–32 was also utilized to detect individual chemical reactions and single Pt nanoparticle collisions based on the reaction between the Ru(bpy)₃²⁺ complex and tri-n-propylamine (TPrA) radicals on the surface of an ITO electrode.^2,33,34 It was found that the size of the nanoparticles, the origin of the interaction between particles and the electrode surface, the concentration of species generation, and the lifetime of individual electrogenerated nanocluster species (i.e., Au₃₈²⁺, Au₃₈³⁺, and Au₃₈⁴⁺) in conjunction with the reactivity of those oxidized species with co-reactant radical intermediates (i.e., TPrA radical) play crucial roles in the frequency of the ECL reaction events leading to individual ECL responses. More strikingly, a higher ECL reaction frequency is directly proportional to the amount of collected ECL light.²¹ Chen and co-workers also employed ECL to study stationary single gold-platinum nanoparticle reactivity on the surface of an ITO electrode.³⁵ Lin and co-workers monitored the hydrogen evolution reaction in the course of “ON” and “OFF” ECL signals.³⁶ Recently, we performed a systematic and mechanistic ECL study of a series of gold nanoclusters, with the general formula of Au_n(SC₂H₄Ph)_m^z (n = 25, 38, 144, m = 18, 24, 60 and z = −1, 0, +1), where near-infrared (NIR) ECL emission was observed.³⁷ There are several enhancement factors, such as catalytic loops^38,39 that improve the signal to noise ratio. The Wightman group was able to report single ECL reactions based on the capability of ECL.⁷ Furthermore, thus far, we have explored ECL mechanisms and reported the ECL efficiency of five different gold nanoclusters i.e., Au₂₅(SR)₁₈¹⁻, Au₂₅(SR)₁₈⁰, Au₂₅(SR)₁₈¹⁺, Au₃₈(SR)₂₄⁰ and Au₁₄₄(SR)₆₀⁰, among which the Au₃₈(SR)₂₄⁰/TPrA system revealed outstanding ECL efficiency, ca. 3.5 times higher than that of Ru(bpy)₃²⁺/TPrA as a gold standard. Therefore, we decided to focus on the Au₃₈ (SR)₂₄⁰/TPrA system. It was discovered that the ECL emission of these nanomaterials can be tuned through varying the applied potential and local concentration of the desired co-reactant.Herein, for the first time we report on ECL via a single Au₃₈(SC₂H₄Ph)₂₄ nanocluster (hereafter denoted as Au₃₈ NC) reaction (eq. (1)) in the vicinity of an UME in the presence of TPrA radicals as a reductive co-reactant.1where x is the oxidation number that can be either 0, 1, 2, 3 or 4. Single ECL spikes (Fig. 1A) along with ECL spectroscopy were used for elucidating individual reaction events. Indeed, each single ECL spike demonstrates a single Au₃₈^(x−1)* reaction product. Au₃₈ NCs were synthesized according to procedures reported by us and others, and fully characterized using UV-Visible-NIR, photoluminescence, ¹HNMR spectroscopy and MALDI mass spectrometry to confirm the Au₃₈ nanocluster synthesis (details are provided in ESI, Sections 1–3, Fig. S1–S4^†).^38,40,41Fig. 2 (left) shows a differential pulse voltammogram (DPV) in an anodic scan of a 2 mm Pt disc electrode immersed in 0.1 mM Au₃₈ acetonitrile/benzene solution containing 0.1 M TBAPF₆ as the supporting electrolyte. There are five discrete electrochemical peaks at which Au₃₈⁰ was oxidized to Au₃₈⁺ (E°′ = 0.39 V), Au₃₈²⁺ (E°′ = 0.60 V), and Au₃₈^3+/4+ (E°′ = 0.99 V) and reduced to Au₃₈⁻ (E°′ = −0.76 V) and Au₃₈²⁻ (E°′ = −1.01 V).^38,40,41Open in a separate windowFig. 1(A) An example of the reaction event transient of 10 μM Au₃₈ in benzene/acetonitrile (1 : 1) containing 0.1 M TBAPF₆ in the presence of 20 mM TPrA at 0.9 V vs. SCE, acquired at 15 ms time intervals using a 10 μm Pt UME. The white dashed-line indicates the threshold to identify single ECL spikes. (B) Illustration of a single nanocluster ECL spike. (C) ECL instrumentation with an inset showing ECL spike generation in the vicinity of the Pt UME.Open in a separate windowFig. 2Anodic DPV for Au₃₈ (left), reaction energy diagram of Au₃₈²⁺ and TPrA· (middle) along with the ECL–voltage curve (right) in an anodic potential scan at a 2 mm Pt disk electrode immersed in a solution of 10 μM Au₃₈ with 20 mM TPrA.The rich electrochemistry of Au₃₈ NCs is well-matched with that of co-reactants such as TPrA to generate near infrared-ECL (NIR-ECL), and the ECL emission efficiency of the Au₃₈/TPrA system is 3.5 times larger than that of the Ru(bpy)₃²⁺/TPrA co-reactant ECL system.²⁷Thus, it is of utmost interest to investigate the ECL generation of the above co-reactant system in single reactions, which improves the ECL signal detection sensitivity. To perform the ECL experiment a solution of 10 μM Au₃₈ NC with 20 mM TPrA was prepared. We first confirmed the ECL light generation of such solution along with its blank solution containing only TPrA using a typical 2 mm diameter Pt disk electrode (Fig. 2, S5 and S6^†).A 10 μm Pt UME electrode, which is electrochemically inert (Fig. S7^†), was utilized to investigate the ECL of single NC reactions under potentiostatic conditions, at which a specific positive bias potential was applied to oxidize both Au₃₈ and TPrA. Fig. 1A shows a typical ECL–time transient current curve (ECL intensity versus time) at 0.90 V vs. SCE, which was acquired using a photomultiplier tube (PMT, R928) for a duration of 1800 s at data acquisition time intervals of 15 ms (Fig. 1C and ESI, Section 3^†). Fig. 1B represents an exemplary event of a single ECL spike with a sharp increase followed by a decay in the ECL intensity. It is observed from the many spikes in Fig. 1B that this process can reoccur with a high probability in the vicinity of the UME, probably due to an electrocatalytic reaction loop (Fig. 1C). Indeed, ECL intensity was enhanced in this way as an already relaxed species, i.e., Au₃₈^z+1*, participates in an oxidation step to regenerate Au₃₈^z+1 to react with the TPrA radical (TPrA˙).Once photons resulting from the excited state relaxation in the vicinity of the UME are captured by the PMT, individual reaction events can be observed (Fig. 1A with the instrumentation schematic shown in Fig. 1C). As shown in Fig. 3A, there are many ECL spikes during 1800 s of measurement, each of which represents an individual ECL generation reaction in the vicinity of the UME surface. It is worth noting that there are several spikes with various intensities. This is most likely due to the Brownian motion which is random movement due to the diffusion of individual nanocluster species such as Au₃₈⁰, Au₃₈¹⁺, Au₃₈²⁺, etc., electrogenerated at the local applied potentials. Long and co-workers⁴² proposed that silver nanoparticle collision on the surface of a gold electrode follows Brownian motion, leading to several types of surface-nanoparticle response peak shapes. In fact, the observed ECL spikes, shown in Fig. 1C, with a rise and an exponential decay suggested that Au₃₈ nanocluster species diffuse directly through the electrode double-layer, move towards the tunneling region of the electrode surface, collide⁴² and become oxidized, react with TPrA radicals thereafter to produce excited states, and emit ECL. It is worth emphasizing that this path could be partially different for each individual nanocluster owing to the angle and direction relative to the electrode surface. The single Au₃₈ NC reaction behaviour at various bias potentials was investigated following the electrochemical energy diagram shown in Fig. 2, middle. For example, at a bias potential of 0.70 V (the green spot on the DPV in Fig. 2), Au₃₈⁰ undergoes two successive oxidation reactions to Au₃₈²⁺ and TPrA oxidation and deprotonation start to generate TPrA·. In fact, at a very close oxidation potential to Au₃₈²⁺, TPrA is also oxidized to its corresponding cation radical (ca. 0.80 V vs. SCE) Fig. S6,^† followed by deprotonation to form the TPrA radical.³⁸ The TPrA· with a very high reduction power (E°′ = −1.7 eV)⁴³ injects one electron to the LUMO orbital of the nanocluster and forms excited state Au₃₈⁺*, as illustrated in the reaction energy diagram in Fig. 2, middle.³⁸ Then, Au₃₈⁺* emits ECL light while relaxing to the ground state. For another instance, at 1.10 V vs. SCE (the red spot on the DPV in Fig. 2), Au₃₈⁰ is oxidized to Au₃₈^3/4+ feasibly. At this potential, the TPrA radical is generated massively in the vicinity of the electrode. The efficient electron transfer between the TPrA radical and Au₃₈^3/4+ generates both Au₃₈²⁺* and Au₃₈³⁺* that emit light at the same wavelength of 930 nm.³⁸ The results of such interactions produced a transient composed of many ECL events (Fig. 3A), which is an indication of bias potential enforcement on the nanocluster light emission.Open in a separate windowFig. 3Single-nanocluster ECL photoelectron spectroscopy of Au₃₈. ECL–time transients (A), statistics of the number of photons (B), histogram of the single reaction time between sequential spikes (C) and accumulated ECL spectrum (D) for a 10 μm Pt UME at 1.1 V immersed in a 10 μM Au₃₈ nanocluster solution in benzene/acetonitrile (1 : 1) containing 0.1 M TBAPF₆ in the presence of 20 mM TPrA. (E)–(H) The counterpart plots to (A)–(D) for the UME biased at 0.7 V. # represents the number.We further tried to collect the current–time traces of such events; however, owing to the high background current originating from the high concentration of TPrA relative to that of the nanocluster, no noticeable spikes in the current were observed.In order to study the photochemistry and understand deeply the single nanocluster reactions, ECL–time transients were collected at different applied potentials (i.e., 0.7, 0.8, 0.9 and 1.1 V vs. SCE) as labelled in green, brown, purple, and red on the DPV in Fig. 2, respectively. The transients were further analysed using our home-written MATLAB algorithm adapted from that for nanopore electrochemistry.⁴⁴ The population of individual events was identified by applying an appropriate threshold to discriminate ECL spikes from the noise as demonstrated in Fig. 1A. In fact, the applied algorithm also assisted us to learn about the raising time and intensity of each spike, as well as photons of individual spikes. For instance, Fig. 3A shows another typical transit for 1800 s at an UME potential bias of 1.1 V for the ECL events. Indeed, the integrated area of each peak, the charge of the photoelectrons at the PMT, is directly proportional to the number of photons emitted from individual reactions (see ESI, Section 5^†). Basically, the PMT amplifies the collected single photon emitted in the course of light-to-photoelectron conversion (see ESI, Section 6 and Fig. S8^†) and translates a single photon into photoelectrons. The extracted charge of each ECL reaction, Q_ECL, was then converted to the corresponding number of photons by dividing by the gain factor, g, which is 1.55 × 10⁶ (Fig. S8^†), following eqn (2):2The histograms of the number of photons show a Gaussian distribution (Fig. 3B) with a reaction frequency of 53.5 ± 2.9 at E = 1.1 V, whereas at a lower potential of 0.7 V the reaction frequency drops to 18.5 ± 1.7 (Fig. 3F). This indicates that there is a three-fold lower reaction occurrence at the lower potential. The integration of the Gaussian fitting at 1.1 V and 0.7 V also reveals a three-fold drop from 3.3 × 10⁵ to 1.2 × 10⁵ photons over 1800 s.To further explore the effect of electrode potential bias on the single Au₃₈ NCs ECL reaction, potentials lower than 1.1 and higher than 0.7 V, ca. 0.8 and 0.9 V (brown and purple labels in Fig. 2), were applied. In fact, the resulting ECL–time transients show a lower population of single spikes (Fig. S12A and ESI,^†). The integrated Gaussian curve values support the ECL–time transient observations with ∼4.1 × 10⁴ and ∼6.5 × 10⁴ photons, respectively. In fact, it is unlikely that the PMT would get more than two events in the duration, owing to the following reasons: (i) it has been shown that only 5.5% of incoming photons can be effectively converted to photoelectron signals by our R928 PMT during our absolute efficiency calibration, ESI Section 6 and Fig. S8–S19^†;⁴⁵ (ii) spherical ECL emission is proven to be detected for a substantial small part upon examination of our detection system for the absolute ECL quantum efficiency;⁴⁵ (iii) Au₃₈ nanocluster ECL emissions occur at 930 nm, which is almost at the wavelength detection limit of our PMT response curve.^38,45In addition, we evaluated the stochastic (a series of random events at various probability distributions) nature of the observed events and extracted the reaction time interval (τ) at various potentials. The resulting graph shows an exponential decay (Fig. 3C) as expressed in eqn (3):3where frequency (λ) gives the mean rate of the event and A represents the fitting amplitude. One can expect to obtain the distribution of the number of emitted photons and spatial brightness function. In fact, the exponential decay is a clear indication of random single reaction events as Whiteman and co-workers described for a 9,10-diphenylanthracene (DPA) ECL system in the annihilation pathway.^7,46 At a potential of 1.1 V, λ and A are found to be 4.98 ± 0.02 ms⁻¹ and 80.4 ± 3.2, whereas at 0.7 V, λ and A turned out to be 32.9 ± 1.6 ms⁻¹ and 9.5 ± 0.1 (Fig. 3C and G). Indeed, the lower potential of 0.70 V vs. SCE is high enough to generate the TPrA radical along with Au₃₈²⁺, thereby leading to excited Au₃₈⁺*, Fig. 3E. One can conclude that at the applied potentials of 0.7 V and 1.1 V, Au₃₈⁰ is oxidized to Au₃₈²⁺ and Au₃₈⁴⁺, resulting in the generation of Au₃₈⁺* and Au₃₈³⁺* under static conditions. Thus, there are higher populations of ECL spikes with no discrepancy in the number of collected photon distributions. However, at two intermediate potentials, i.e., 0.8 and 0.9 V, a dynamic behaviour which is due to the mixed oxidation of Au₃₈ species, in the vicinity of the UME, is observed. In fact, at these two applied potentials, the local concentration of the corresponding gold nanoclusters (i.e., Au₃₈³⁺ and Au₃₈⁴⁺) is not sufficient to produce significant ECL spikes. We also attempted to collect the ECL spectrum using a charge-coupled device (CCD) camera, which is relatively more sensitive in the NIR region (e.g., λ > 900 nm, Fig. S16^†). Fig. 3D and H display an accumulated spectrum at 1.1 and 0.7 V vs. SCE, which is collected for 30 minutes. The fitted accumulated ECL spectrum indicates an ECL peak emission at 930 nm and supports higher reactivity at 1.1 V than that at 0.7 V.³⁸ To confirm that the observed ECL spikes and accumulated spectra are generated based on the oxidation of Au₃₈ nanoclusters in the presence of TPrA radicals, ECL–time transients were recorded upon holding an applied potential at which no faradaic process occurs. Fig. S11^† represents ECL–time curves and accumulated ECL spectra at 0.0 V and 0.4 V. One can notice that no appreciable ECL signal can be observed.In addition, we investigate the Pearson cross-correlation (ρ) between the intensities of ECL spikes with τ as shown in Fig. S14^† in which there is a positive correlation at 0.7 and 1.0 V and a negative correlation at 0.8 and 0.9 V. In fact, ρ evaluates whether there is a stationary random process between the two defined parameters (see ESI, Section 6^†). Interestingly, the frequency of the reaction at different applied potentials revealed decay from 0.7 to 0.8 V, followed by an upward trend to 0.9 and 1.1 V vs. SCE (Fig. S15^†). This could be additional support for the transition stage at 0.8 and 0.9 V, where the applied potential as the major driving force to generate oxidized forms (e.g., Au₃₈³⁺ and Au₃₈⁴⁺) governs the flux of the nanocluster species that reach the vicinity of the electrode. Furthermore, the effectiveness of electron transfer reaction kinetics between the radical species, i.e., Au₃₈^z+1 and TPrA radical, competes with the flow of the incoming nanoclusters. It is worth mentioning that each of the ECL single event experiments was repeated three times, and very similar results were obtained. Moreover, lower (5 μM) and higher (20 μM) concentrations of Au₃₈ in the presence of 20 mM were tested. In fact, the former shows a smaller number of single reactions; however the later revealed a larger number of multiple reactions (Fig. S13^†).In summary, in this communication we demonstrated that Au₃₈ NC ECL at the single reaction level can be monitored using a simple photoelectrochemical setup following a straightforward protocol. Indeed, we have rich basic knowledge about the ECL mechanisms of various gold nanoclusters with different charge states (Au₂₅(SR)₁₈¹⁺, Au₂₅(SR)₁₈⁰, Au₂₅(SR)₁₈¹⁻) and various sizes (Au₂₅(SR)₁₈⁰, Au₃₈(SR)₂₄⁰, Au₁₄₄(SR)₆₀⁰) in fine detail. Thus, the ECL emission mechanisms of gold clusters, including the contribution of each charge state and influence of various concentrations of co-reactants, are well known. For instance, in our previous studies^{38,39,47–49} we clearly identified three charge states of an Au₂₅(SR)₁₈¹⁻/TPrA system and we discovered that at a high concentration of TPrA the reduction in the bulk solution of gold nanoclusters influences the ECL emission wavelength. We also have learnt that the Au₃₈/TPrA system is a co-reactant independent of co-reactant concentration. Furthermore, an extensively higher concentration of TPrA provides a dominant reaction over any unknown decomposition reaction at higher oxidation states of Au₃₈. It was discovered that the population of ECL reactions is directly governed by the applied bias potential on a Pt UME. This work is a strong indication of the high sensitivity of the ECL technique in detecting single ECL reactions in a simple solution, which complements those reported by the Bard group using rubrene, for instance, embedded in an organic emulsion in the presence of TPrA or oxalate as a co-reactant.^50,51 These systems needed a substantial ECL enhancement in the presence of an ionic liquid as the supporting electrolyte and emulsifier. The current approach can be further extended to investigate other molecules and nanomaterials'' electrocatalytic processes at the single reaction level.     

60Co γ‐Irradiation‐Initiated “Living” Free‐Radical Polymerization in the Presence of Dibenzyl Trithiocarbonate

The free‐radical polymerization of vinyl monomers in the presence of dibenzyl trithiocarbonate (DBTTC) and under ⁶⁰Co γ‐irradiation is of living character. Under ⁶⁰Co irradiation, the bonds between benzyl group and sulfur were cleaved, benzyl radicals initiate the polymerization. The propagating radical together with trithiocarbonate radicals form a dormant polymer chain. The fast equilibrium between propagation radical and dormant polymer chain controls the polymerization.     

X-ray microscopy of novel thermoplastic/liquid crystalline polymer blends by mechanical alloying

Incorporation of liquid crystalline polymers (LCPs) into commodity polymers remains a challenge in the design of high-performance, low-cost polymeric blends. Blends of a thermoplastic polymer and a nematic LCP are produced here by mechanical alloying. Functionality sensitive X-ray microscopy reveals LCP dispersions as small as 100 nm in diameter. Intimate mixing remains upon subsequent melt processing, indicating that mechanical alloying is suited for applications such as recycling.