动态特性的参数设计在差示光度法测金中的应用

本文提出对动态特性参数设计使用相关系数与信噪比作为内表指标进行分析 ,并使用该分析方法优化了差示光度法测较高浓度金矿样的试验条件。     

A sagittally focusing double‐multilayer monochromator for ultrafast X‐ray imaging applications

The development of a sagittally focusing double‐multilayer monochromator is reported, which produces a spatially extended wide‐bandpass X‐ray beam from an intense synchrotron bending‐magnet source at the Advanced Photon Source, for ultrafast X‐ray radiography and tomography applications. This monochromator consists of two W/B₄C multilayers with a 25 Å period coated on Si single‐crystal substrates. The second multilayer is mounted on a sagittally focusing bender, which can dynamically change the bending radius of the multilayer in order to condense and focus the beam to various points along the beamline. With this new apparatus, it becomes possible to adjust the X‐ray beam size to best match the area detector size and the object size to facilitate more efficient data collection using ultrafast X‐ray radiography and tomography.     

Design of interdigital transducers for crack detection in plates

Interdigital transducers (IDT) for non-destructive evaluation (NDE) of cracks in plates are designed based on an analytical model established previously. Key considerations include mode selectivity, excitation strength, collimation of wave and cost. The advantage of mode selectivity of IDT over PZT patch is presented both analytically and experimentally. Effects of parameters, namely finger spacing, width, length, number of fingers, and the size of IDT, on the excitation strength and mode selectivity are considered. This led to the design of a mobile double-sided IDT as an efficient device where excitation strength is strong and focused. The device was fabricated in-house using commercially available piezoelectric ceramics and used to develop a procedure for accurate identification of the direction and extent of cracks in plates. Three aluminum plates, one with a linear deep crack, another with a piecewise linear shallower crack and the third with a curved crack, were used to illustrate the accuracy and efficiency of both the proposed device and procedure for effective NDE.     

Theoretical analysis and experimental verification of a cost-effective chromatic dispersion monitoring method in a 40-Gb/s optical fiber communication system

A cost-effective technique for in-service chromatic dispersion monitoring in a 40-Gb/s optical communication system is proposed. Microwave devices are adopted to detect the electrical power of a specific frequency band. A simplified theoretical model is proposed and discussed focusing on the relationship between electrical power and chromatic dispersion at different frequency bands. The dynamic monitoring of chromatic dispersion is achieved using devices such as PIN detector, microwave amplifier, narrow-band microwave filter, and electrical power detector. The maximum detectable chromatic dispersion is 130 ps/nm and a resolution of 5.2 ps/nm/dB has been achieved in the frequency band centered at 12 GHz.     

基于新型电荷生成层的P-i-N结构白色有机叠层电致发光器件

采用2,9-Dimethyl-4,7-diphenyl-1,10-phenanthroline(BCP): 5 wt.% cesium carbonate(Cs₂CO₃)和N, N'-Bis(naphthalen-1-yl)-N,N'-bis(phenyl)-benzidine(NPB): 20 wt.% molybdenum oxide(MoO₃)分别作为器件的电子注入层和空穴注入层,研究了N型和P-i-N结构有机电致发光器件的载流子传输特性.载流子传输层中BCP: Cs₂CO₃和NPB:MoO₃的引入有效增强了载流子注入能力,从而降低了器件的驱动电压.基于新型电荷生成层BCP: 5 wt.% Cs₂CO₃/ NPB: 20 wt.% MoO₃制备了色稳定、高效率P-i-N结构有机叠层器件.与单元器件相比,引入新电荷生成层有机叠层器件的最大电流效率增大了2.5倍,表明该电荷生成层可以有效地将电子和空穴分别注入到相邻发光单元中.采用该电荷生成层制备了P-i-N结构白色有机叠层器件,器件的上下发光单元分别为橙光和蓝光发射.当发光亮度从500增加到5 000 cd/m²时,器件的色坐标稳定在(0.33, 0.29)附近,接近白光等能点.利用单色发光单元堆叠制备白色有机叠层器件的方法为实现色稳定、高效率的白色有机电致发光器件提供了一种有效的途径.     

Ge组分分布对基区杂质非均匀分布的SiGe HBT温度特性的影响

众所周知, 双极型晶体管的设计主要是基区的设计. 一般而言, 基区的杂质分布是非均匀的. 本文首先研究了非均匀的杂质高斯分布对器件温度分布、增益和截止频率的温度特性的影响, 发现增益和截止频率具有正温度系数, 体内温度较高. 随后研究了基区Ge组分分布对这些器件参数的影响. 均匀Ge组分分布和梯形Ge组分分布的SiGe 异质结双极型晶体管增益和截止频率具有负温度系数, 具有较好的体内温度分布. 进一步的研究表明, 具有梯形Ge组分分布的SiGe 异质结双极型晶体管, 由于Ge组分缓变引入了少子加速电场, 不但使它的增益和截止频率具有较高的值, 而且保持了较弱的温度敏感性, 在增益、特征频率大小及其温度敏感性、体内温度分布达到了很好的折中.     

反射率的数值反演

通过分析热流边界条件下的一维热传导过程,提出并实现了由后表面温度变化历史曲线反演前表面反射率变化历史曲线的数值方法。通过一维热传导的正向和反演计算过程,验证了反演程序的可靠性。对数值反演计算和实验测量两种方式得到的反射率曲线进行了对比,结果显示,两条反射率曲线在变化趋势上符合较好,初步验证了一维温度场中数值反演方法的可行性。     

棉花冠层水分含量估算的高光谱指数研究

适宜的光谱指数对于地表参数高光谱诊断模型的估算精度具有决定性作用。通过不同棉花冠层水分含量表征参数冠层等效水厚度EWT_canopy, 植株含水量VWC及其对应的光谱数据分析,构建350～2 500 nm范围内所有波段两两组合的比值指数RVI和归一化指数NDVI,分析水分含量表征参数与所有指数之间的相关关系,筛选最大相关系数对应的指数作为最佳水分指数,利用新指数构建水分含量表征参数的估算模型,并与已知的各种水分指数估算精度进行比较。结果表明：新建比值指数R_{1 475}/R_{1 424}及其归一化指数(R_{1 475}-R_{1 424})/(R_{1 475}+R_{1 424})对EWT_canopy的估算效果最佳,由其得到的估算值与实测值之间的相关系数r值达到0.849;已知指数(R₈₃₅-R_{1 650})/(R₈₃₅+R_{1 650})对VWC的估算效果最佳,由其得到估算值与实测值之间的相关系数r值为0.805。     

波纹管对超导电缆出口液氮温度的影响

建立了30米长高温超导电缆的二维模型,利用Fluent软件对该模型进行仿真分析。在该模型中,采用波纹管恒温器,分析了波纹管的波距、波高等因素对出口液氮温度的影响。结果表明:在相同的热负荷及流量下,波纹管的波距越小,波高越大,出口液氮温度越高。超导电缆波纹管内液氮温度模拟,为低温冷却系统的优化设计提供理论依据。     

110kV冷绝缘高温超导电缆在故障电流下的温度计算与分析

研究了110kV冷绝缘高温超导电缆失超时,故障电流的分流情况,并以此为依据,建立了电缆在故障电流下失超时,温升与时间关系的计算模型;通过MATLAB对计算模型进行了求解,并对求解结果进行了分析;计算出了电缆在不同故障电流下,温度上升到不同值所需要的时间,进一步明确了故障电流的大小对电缆温升的影响。