窗口可变滑动相关分析方法在激光诱导击穿光谱谱线自动识别中的应用

激光诱导击穿光谱(LIBS)谱线具有很窄的展宽,且光谱仪因外界温度条件的变化存在波长漂移,光谱数据为离散数字信号,受噪声、谱线重叠及连续背景的影响,信号存在失真和变形。而目前光谱仪自带谱线识别分析软件主要以"就近原则"为主,错误率较高,必须依赖于人眼的观察对比。针对这个问题,在研究LIBS光谱特性的基础上,提出了一种窗口可变滑动相关分析方法(CAASW),用于激光诱导击穿光谱谱线自动识别。以土壤标准物质为样品,对该方法进行了实验分析和评价,与光谱仪自带分析识别软件相比,CAASW明显提高了识别准确率和识别速度,最终实现了谱线的自动识别。     

聚苯乙烯多孔薄膜的密度梯度控制

利用单分散的SiO2微球自组装制备了含一种尺寸微球的SiO2胶体晶体和含多种尺寸微球的多层异质结构。对含一种尺寸微球的SiO2胶体晶体进行煅烧和刻蚀处理后,胶体晶体中空隙所占比例大于立方密堆结构的26%,形成了非密堆结构,而且刻蚀时间越长,空隙比例越大。在同样的热处理和刻蚀条件下,微球尺寸越小的胶体晶体被刻蚀的程度越高,结构中空气空隙所占的比例越大。对SiO2多层异质结构经过煅烧和刻蚀处理后,得到了空隙梯度变化的多层结构,以此为模板制备了密度梯度变化的聚苯乙烯多孔薄膜。薄膜各层之间形成了平滑的过渡,没有显示出明显的层间缺陷,且孔与孔之间没有出现3维有序多孔结构中常见的大的连通孔道。     

基于衍射理论的Z扫描技术分析与数值模拟

以菲涅耳-基尔霍夫衍射理论为基础,对通过非线性介质的高斯光束传输行为进行理论分析,分别给出了强吸收、无吸收情况下开孔、闭孔Z扫描曲线公式;对不同条件下非线性介质的归一化透过率进行数值模拟计算,发现Z扫描曲线透射峰和透射谷表现出3种新的特性:随着入射激光峰值光强的增加,Z扫描曲线透射峰的高度受到抑制,而透射谷则加强变得更深;非线性相移的增加对Z扫描曲线透射峰和透射谷均有增高和加深的作用;激光束束腰半径越大,Z扫描曲线的峰谷特征越明显。     

磁绝缘传输线阻抗变化对空间电子流的影响

介绍了磁绝缘传输线的阻抗大小、传输电压及电流大小对其产生的空间电子流大小及阴极电子鞘层厚度的影响。运用CHIPIC软件建立四层圆盘锥形磁绝缘传输线A层的近似化三维模型进行模拟,对比理论计算值与模拟值,并与相关文献的二维模拟结果进行对照,验证三维模拟的正确性。最后,模拟研究了圆盘锥形磁绝缘传输线阴阳极之间的间距变化对传输效率的影响。     

Improving InGaN-LED performance by optimizing the patterned sapphire substrate shape

The epitaxial growths of GaN films and GaN-based LEDs on various patterned sapphire substrates (PSSes) with different values of fill factor (f) and slanted angle (θ) are investigated in detail. The threading dislocation (TD) density is lower in the film grown on the PSS with a smaller fill factor, resulting in a higher internal quantum efficiency (IQE). Also the ability of the LED to withstand the electrostatic discharge (ESD) increases as the fill factor decreases. The illumination output power of the LED is affected by both θ and f. It is found that the illumination output power of the LED grown on the PSS with a lower production of tanθ and f is higher than that with a higher production of tanθ and f.     

噪声诱导的二维复时空系统的同步研究

研究了一类噪声诱导的二维复时空系统的同步问题.首先讨论了二维复Ginzburg-Laudau(CGL) 方程随时间和空间变化的时空混沌特性;其次,研究了时空噪声驱动下CGL系统的同步问题.理论上利用线性稳定性分析,得到了常数激励下CGL系统达到稳定态的临界强度;结合噪声的随机性和非零均值特性, 揭示了噪声诱导同步的机理;并从理论上和数值上分别给出了达到同步所需要的控制参数和噪声强度满足的条件,实现了两个非耦合CGL系统的完全同步.结果表明,数值模拟和理论分析有很好的一致性.     

Fabrication of aligned single wall carbon nanotube absorbers for high power passive mode-locked Nd:GdVO<Subscript>4</Subscript> laser

Using the vertical evaporation technique we fabricated saturable absorbers by transferring the water-soluble single wall carbon nanotubes (SWCNT) onto a hydrophilic quartz substrate. The fast recovery times of the absorber were measured to be 136 and 790 fs. The modulation depth of the absorber was about 2%. Passive mode-locked Nd:GdVO₄ laser using such an absorber was demonstrated. The continuous wave mode-locked pulses with the pulse duration of 12.4 ps and the repetition of 120 MHz were achieved. The maximum average output power of the mode-locked laser is 2.4 W at the pump power of 13 W. Such kind of absorber has potential to be put into practical use for high power solid-state laser mode locking.     

PH, PD和PT分子常数理论研究

采用内收缩多参考组态相互作用(MRCI)方法和包含Davidson修正(+Q) 的MRCI方法结合相关一致基aug-cc-pV5Z研究了PH (X³Σ^-, a¹Δ和A³∏)分子的势能曲线. 在同位素质量识别的基础上对势能曲线进行拟合, 得到PH, PD和PT分子各个电子态的光谱常数(T_e, R_e, ω_e, ω_ex_e, α_e和 B_e). 通过与已有实验数据的比较发现, 本文的结果与实验结果非常一致. 对于PH, PD和PT分子的Σ^-电子态, 计算得到了J = 0时的前12个振动态. 对于每一个振动态, 还分别计算了它的振动能级、惯性转动常数和离心畸变常数. 与其他理论结果和实验数据进行比较可知, 本文的结果更精确、更完整. 文中PD和PT分子的光谱常数和分子常数均属首次报导.     

菱形纤芯光子晶体光纤色散与双折射特性分析

针对光子晶体光纤多零色散点、高双折射的应用要求, 设计了一种新型结构的光子晶体光纤, 其纤芯由位于菱形四个角上的圆形空气孔组成. 通过有限元数值分析方法对该种结构光子晶体光纤的色散特性和双折射特性进行数值仿真, 得到色散与波长、色散与纤芯圆孔尺寸、双折射与波长、双折射与纤芯圆孔尺寸的关系. 研究结果表明:在满足光纤传输功率要求的条件下, 光纤的双折射在d₁<0.8 μupm 时的性能较好. 同时, 该种结构的光子晶体光纤在芯区直径满足d₁=0.4 μupm或 d     

X-ray submicrometer phase contrast imaging with a Fresnel zone plate and a two dimensional grating interferometer

The application of a two dimensional (2D) grating interferometer-Fresnel zone plate combination for quantitative submicron phase contrast imaging is reported. The combination of the two optical elements allows quick recovery of the phase shift introduced by a sample in a hard X-ray beam, avoiding artifacts observed when using the one dimensional (1D) interferometer for a sample with features oriented in the unsensitive direction of the interferometer. The setup provides submicron resolution due to the optics magnification ratio and a fine sensitivity in both transverse orientations due to the 2D analysis gratings. The method opens up possibilities for sub-micro phase contrast tomography of microscopic objects made of light and/or homogeneous materials with randomly oriented features.