Determination of tyrosine traces by adsorption voltammetry of its copper (II) complex

The electrochemical behavior of the copper-tyrosine complex has been studied by linear-sweep adsorption voltammetry. In 0.02 mol/L Na₂HPO₄ buffer solution (pH=9.6), the complex can be adsorped on a hanging mercury drop electrode and reduced at a peak potential of about –0.42 V (vs. SCE). The secondary derivative peak height is linear proportional to the concentration of tyrosine in the range 1.0×10^–7–5.0×10^–5 mol/L. The detection limit is 5×10^–8 mol/L.Project supported by the Provincial Science Foundation of Shandong Province     

Selective quenching of tryptophanyl fluorescence in bovine serum albumin by the iodide ion

Modified Stern-Volmer equation is obeyed by bovine serum albumin (BSA)-iodide system showing selective quenching of tryptophanyl fluorescence of BSA. The fraction of accessible protein fluorescence is 0.56 and the effective Stern-Volmer constant is 290 M^-1 at pH 7.4 in 0.005 M phosphate buffer at 25°C. Collisional quenching is operative both in the BSA -I⁻¹ system and the model system, tryptophan-I⁻¹. It is supported by the observed relationship between the ratio of quenching rate constants (k _q ) and diffusion coefficients and alsok _q with bulk viscosity.     

Thickness and temperature dependence of subsidiary absorption thresholds in yttrium-iron-garnet thin films

The microwave subsidiary absorption threshold in tangentially magnetized yttrium-iron-garnet (YIG) films was measured as a function of the static magnetic field, film thickness and decrease in the 0.3–3 μm range is observed. The effect is explained quantitatively by using modified Damon-Eshbach dispersion relations which take into account exchange interactions.

The effect of temperature on h_crit, the smallest threshold field amplitude, in the 250<T< 450 K temperature range can be expressed by an empirical relationship h_crit M_s(T)^-1.6 where M_s is the saturation magnetization. This h_crit vs M_s relationship is similar to that obtained for the magnetization dependence of parallel pump thresholds in Li-Ti ferrite compounds.     

EPMA of interfaces applied to the solid oxide fuel cell

Chemical interactions at the phase boundaries of materials applied for the solid oxide fuel cell (SOFC) have been studied by EPMA. The chemical reactivity at the interface of La_y-xSr_xMnO₃/ZrO₂-Y₂O₃ is dependent on the stoichiometry (y) and the Sr content (x) of the perovskite. Typical reaction products (zirconates) and a diffusion zone in the ZrO₂–Y₂O₃ have been observed. The extension of cation release (Mn) is related to the increasing chemical activity of Mn oxide in the perovskite by the Sr substitution for La. The wettability of the metal/oxide interface in the anode cermet (Ni/ZrO₂–Y₂O₃) has been found to be influenced by chemical reactions resulting from the applied reducing atmosphere with high carbon activity. The disintegration of ZrO₂–Y₂O₃ in contact with molten Ni or Ni-Ti and Ni-Cr alloys leads to the redeposition of Y₂O₃-enriched oxides and also to Zr-rich intermetallic compounds and eutectics.     

(ΩΩ)0+ Dibaryon Productions in Central Au+Au Collisions at RHIC Energy(SNN)= 130 GeV

Based on the measured transverse mass spectra ofπr-, K-, and p at the RHIC energy s()NN = 130 GeV,di-omega productions from baryon-baryon reactions in hadronic matter are studied. Results about the (ΩΩ)0+ numbershow that the deeply bound state (ΩΩ)o+ can be observed at RHIC energies.     

Development of new dyes for use in integrated optical sensors

New chromoionophores have been developed, focused on NIR applications so that optode membranes may be used in monolithically integrated optical sensors. The wavelength of maximum absorbance has been estimated for a new model compound by the Pariser-Parr-Pople (PPP) method. Several cyanine type dyes have been tested as membrane chromoionophores. Membrane composition has been altered to overcome solubility problems. In this way, simple pH-sensitive optode membranes have been produced.     

Database reverse engineering: From requirements to CARE tools

This paper analyzes the requirements that CASE tools should meet for effective database reverse engineering (DBRE), and proposes a general architecture for data-centered applications reverse engineering CASE environments. First, the paper describes a generic DBMS-independent DBRE methodology, then it analyzes the main characteristics of DBRE activities in order to collect a set of desirable requirements. Finally, it describes DB-MAIN, an operational CASE tool developed according to these requirements. The main features of this tool that are described in this paper are its unique generic specification model, its repository, its transformation toolkit, its user interface, the text processors, the assistants, the methodological control and its functional extensibility. Finally, the paper describes five real-world projects in which the methodology and the CASE tool were applied. This is a heavily revised and extended version of “Requirements for Information System Reverse Engineering Support” by J.-L. Hainaut, V. Englebert, J. Henrard, J.-M. Hick, D. Roland, which first appeared in the Proceedings of the Second Working Conference on Reverse Engineering, IEEE Computer Society Press, pp. 136–145, July 1995. This paper presents some results of the DB-MAIN project. This project is partially supported by the Région Wallonne, the European Union, and by a consortium comprising ACEC-OSI (Be), ARIANE-II (Be), Banque UCL (Lux), BBL (Be), Centre de recherche public H. Tudor (Lux), CGER (Be), Cockerill-Sambre (Be), CONCIS (Fr), D'Ieteren (Be), DIGITAL, EDF (Fr), EPFL (CH), Groupe S (Be), IBM, OBLOG Software (Port), ORIGIN (Be), Ville de Namur (Be), Winterthur (Be), 3 Suisses (Be). The DB-Process subproject is supported by the Communauté Fran?aise de Belgique.