Growth of GaN single crystals with extremely low dislocation density by two-step dislocation reduction

We have discovered a mechanism which can significantly reduce the dislocation density during the growth of GaN single crystals in the Na flux method. The significant reduction of the dislocation density occurs in the later stage of LPE growth, rather than solely at the seed-LPE interface for which we have already reported evidence indicating the presence of bundling dislocations. The two-step dislocation reduction is the key in achieving extremely low dislocation density using this method.     

One-step synthesis of hierarchical porous γ-alumina with high surface area

Hierarchical porous γ-alumina is successfully fabricated from a precursor solution consisting of surfactants, polystyrene (PS) spheres, inorganic salts and solvents. After calcinations, uniform macropores are closely packed. The macropore size coincides with the original PS sphere size. These macropores are connected by small windows. In addition, the macropore walls have mesoporous structures, as confirmed by SAXS measurement and TEM observation. After calcination at 900 °C, the amorphous alumina frameworks are converted to the crystallized γ-alumina phase. Even after crystallization, the existence of uniform mesopores and high surface are well retained, though the mesoporous ordering is lower.     

Surface structures and osteoblast response of hydrothermally produced CaTiO3 thin film on Ti-13Nb-13Zr alloy

This study investigated the surface characteristics and in vitro biocompatibility of a titanium (Ti) oxide layer incorporating calcium ions (Ca) obtained by hydrothermal treatment with or without post heat-treatment in the Ti-13Nb-13Zr alloy. The surface characteristics were evaluated by scanning electron microscopy, thin-film X-ray diffractometry, X-ray photoelectron spectroscopy, atomic force microscopy and contact angle measurements. In vitro biocompatibility of the Ca-containing surfaces was assessed in comparison with untreated surfaces using a pre-osteoblast cell line. Hydrothermal treatment produced a crystalline CaTiO₃ layer. Post heat-treatment at 400 °C for 2 h in air significantly decreased water contact angles in the CaTiO₃ layer (p < 0.001). The Ca-incorporated alloy surfaces displayed markedly increased cell viability and ALP activity compared with untreated surfaces (p < 0.001), and also an upregulated expression of various integrin genes (α1, α2, α5, αv, β1 and β3) at an early incubation time-point. Post heat-treatment further increased attachment and ALP activity in cells grown on Ca-incorporated Ti-13Nb-13Zr alloy surfaces. The results indicate that the Ca-incorporated oxide layer produced by hydrothermal treatment and a simple post heat-treatment may be effective in improving bone healing in Ti-13Nb-13Zr alloy implants by enhancing the viability and differentiation of osteoblastic cells.     

Grafting of hyperbranched cyclotriphosphazene polymer onto silica nanoparticle and carbon black surfaces

The surface grafting of hyperbranched cyclotriphosphazene polymer onto silica nanoparticles and carbon black was investigated. The grafting of hyperbranched cyclotriphosphazene polymer onto these surfaces was achieved by the repeated reactions of hexachlorocyclotriphosphazene with hexamethylenediamine from surface amino groups and sodium carboxylate groups, respectively. The percentage of grafting onto silica and carbon black surfaces exceeded 760 and 390%, respectively. However, it proved difficult to achieve the theoretical growth of cyclotriphosphazene polymer from these surfaces because of steric hindrance. The introduction of sulfonic acid groups was successfully achieved by the reaction of terminal chlorophosphazene groups of the hyperbranched polymer‐grafted silica and carbon black with sulfanilic acid. The content of sulfonic acid groups introduced onto silica and carbon black surfaces was 4.98 mmol/g and 5.70 mmol/g, respectively. The sulfonated cyclotriphosphazene polymer‐grafted carbon black was extremely hydrophilic, yielding stable colloidal dispersions in polar solvents. The sulfonated cyclotriphosphazene polymer‐grafted silica and carbon black showed ionic conductivity, with the conductance increasing exponentially with increasing relative humidity and temperature. This study may offer important leads in the application of silica nanoparticles and carbon black in polymeric membranes for fuel cells. © 2008 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 4218–4226, 2008     

Oxidative degradation of poly(isophthaloylhydrazine‐1,2‐diyl)s

The condensation polymerization of isophthalodihydrazide and diphenyl isophthalate affords poly(isophthaloylhydrazine‐1,2‐diyl). High‐molecular‐weight poly(5‐tert‐butylisophthaloylhydrazine‐1,2‐diyl) is prepared by the polycondensation of 5‐tert‐butylisophthalodihydrazide and bis(4‐nitrophenyl) 5‐tert‐butylisophthalate in NMP at 100 °C. T_d of the poly(diacylhydrazine) is observed above 300 °C. No T_g is observed below T_d. The high‐molecular‐weight poly(diacylhydrazine) exhibits a film‐forming ability. The poly(diacylhydrazine) decomposes on treatment with an oxidant such as sodium hypochlorite solution to obtain the corresponding carboxylic acid and nitrogen. However, poly(diacylhydrazine) was stable to oxygen and hydrogen peroxide even in the presence of transition metal ions. © 2008 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 6255–6262, 2008     

Allylation of methylenecyclopropanes with allylindium reagents

Methylenecyclopropanes carrying a hydroxymethyl group at the ring underwent stereoselective allylindation with allylindium sesquiiodide to afford the allylated products, in which the allyl group was delivered at the external sp² carbon via cyclopropylindium intermediates. The reaction of ethyl 2-cyclopropylideneacetate and triallylindium afforded the 1,4-adduct along with dimeric products.