An Efficient Photonic Crystal Fiber-Based Brillouin Erbium Fiber Laser Using a Fiber Bragg Grating for Multi-Wavelength Generation

Abstract

An efficient multi-wavelength Brillouin erbium fiber laser is demonstrated using an improved configuration with a broadband fiber Bragg grating and a piece of photonic crystal fiber. The laser generates more than 55 lines of optical comb with a line spacing of approximately 0.09 nm in a 1,565-5 nm region using pump powers of 3 dBm and 150 mW for the Brillouin and 980-nm pumps, respectively. The Brillouin erbium fiber laser with a fiber Bragg grating's reflectivity of 50% obtained a higher number of comb lines compared to that of 99% reflectivity.     

Synthesis of poly(hydroxamic acid) ligand from polymer grafted corn‐cob cellulose for transition metals extraction

Poly(hydroxamic acid) ligand was synthesized using ester functionalities of cellulose‐graft‐poly(methyl acrylate) copolymer, and products are characterized by Fourier transform infrared spectroscopy, field emission scanning electron microscopy, high‐resolution transmission electron microscopy, and X‐ray photoelectron spectroscopy analysis. The poly(hydroxamic acid) ligand was utilized for the sensing and removal of transition metal ions form aqueous solutions. The solution pH is found a key factor for the optical detection of metal ions, and the reflectance spectra of the [Cu‐ligand]ⁿ⁺ complex were observed to be the highest absorbance 99.5% at pH 6. With the increase of Cu²⁺ ion concentration, the reflectance spectra were increased, and a broad peak at 705 nm indicated that the charge transfer (π‐π transition) complex was formed. The adsorption capacity with copper was found to be superior, 320 mg g^?1, and adsorption capacities for other transition metal ions were also found to be good such as Fe³⁺, Mn²⁺, Co³⁺, Cr³⁺, Ni²⁺, and Zn²⁺ were 255, 260, 300, 280, 233, and 223 mg g^?1, respectively, at pH 6. The experimental data show that all metal ions fitted well with the pseudo‐second‐order rate equation. The sorption results of the transition metal ions onto ligand were well fitted with Langmuir isotherm model (R² > 0.98), which implies the homogenous and monolayer character of poly(hydroxamic acid) ligand surface. Eleven cycles sorption/desorption process were applied to verify the reusability of this adsorbent. The investigation of sorption and extraction efficiency in each cycle indicated that this new type of adsorbent can be recycled in many cycles with no significant loss in its original detection and removal capability. Copyright © 2016 John Wiley & Sons, Ltd.     

Effect of mixed H2O?CH3CN solvent on intramolecular general base-catalyzed cleavage of ionized phenyl salicylate in the presence of DL-proline

Nucleophilic second-order rate constant (K_n ^ms) for the reaction of DL-proline with ionized phenyl salicylate (PS⁻) shows a nonlinear decrease with the increase in the content of CH₃CN in mixed aqueous solvents at ≤50% v/v CH₃CN. The values of k_n ^ms show a mild increase with the increase in the content of CH₃CN at >50% v/v CH₃CN. The effect of solvent on k_n ^ms is explained in terms of solvent effect on the pK_a of the conjugate acids of leaving group (i.e. phenolate ion) and DL-proline.     

Cathodic stripping voltammetry of 2,3-dichloroquinoxaline and 1,4-dichlorophthalazine reactive dyes and their hydrolysis products: Reactive Red 41 and Reactive Red 96

Preliminary studies of the feasibility of monitoring by cathodic stripping voltammetry the hydrolysis of two further types of reactive dyes have been made. The azo reduction peak in differential pulse cathodic stripping voltammograms of the 2,3-dichloroquinoxaline reactive dye, Reactive Red 41, and in those of its hydrolysis product are sufficiently separated for the hydrolysis of Reactive Red 41 to be followed using the heights of these peaks. In the case of the 1,4-dichlorophthalazine reactive dye, Reactive Red 96, the azo peaks of the reactive and hydrolysed dyes are too close to be used to monitor the hydrolysis reaction, but peaks associated with reduction of the 1,4-dichlorophthalazine group are present which could be used to monitor the hydrolysis of Reactive Red 96.     

Higher‐order bounded differencing schemes for compressible and incompressible flows

In recent years, three higher‐order (HO) bounded differencing schemes, namely AVLSMART, CUBISTA and HOAB that were derived by adopting the normalized variable formulation (NVF), have been proposed. In this paper, a comparative study is performed on these schemes to assess their numerical accuracy, computational cost as well as iterative convergence property. All the schemes are formulated on the basis of a new dual‐formulation in order to facilitate their implementations on unstructured meshes. Based on the proposed dual‐formulation, the net effective blending factor (NEBF) of a high‐resolution (HR) scheme can now be measured and its relevance on the accuracy and computational cost of a HR scheme is revealed on three test problems: (1) advection of a scalar step‐profile; (2) 2D transonic flow past a circular arc bump; and (3) 3D lid‐driven incompressible cavity flow. Both density‐based and pressure‐based methods are used for the computations of compressible and incompressible flow, respectively. Computed results show that all the schemes produce solutions which are nearly as accurate as the third‐order QUICK scheme; however, without the unphysical oscillations which are commonly inherited from the HO linear differencing scheme. Generally, it is shown that at higher value of NEBF, a HR scheme can attain better accuracy at the expense of computational cost. Copyright © 2006 John Wiley & Sons, Ltd.     

RETRACTED ARTICLE: Hydrogenated nanocrystalline silicon germanium thin films

Hydrogenated nanocrystalline silicon germanium thin films (nc-SiGe:H) is an interesting alternative material to replace hydrogenated nanocrystalline silicon (nc-Si:H) as the narrow bandgap absorber in an a-Si/a-SiGe/nc-SiGe(nc-Si) triple-junction solar cell due to its higher optical absorption in the wavelength range of interest. In this paper, we present results of optical, structural investigations and electrical characterization of nc-SiGe:H thin films made by hot-wire chemical vapor deposition (HW-CVD) with a coil-shaped tungsten filament and with a disilane/germane/hydrogen gas mixture. The optical band gaps of a-SiGe:H and nc-SiGe:H thin-films, which are deposited with the same disilane/germane/hydrogen gas mixture ratio of 3.4 : 1.7 : 7, are about 1.58 eV and 2.1 eV, respectively. The nc-SiGe:H thin film exhibits a larger optical absorption coefficient of about 2–4 in the 600–900 nm range when compared to nc-Si:H thin film. Therefore, a thinner nc-SiGe:H layer of ∼500 nm thickness may be sufficient for the narrow bandgap absorber in an a-Si based multiple-junction solar cell. We enhanced the transport properties as measured by the photoconductivity frequency mixing technique. These improved alloys do not necessarily show an improvement in the degree of structural heterogeneity on the nanometer scale as measured by smallangle X-ray scattering. Decreasing both the filament temperature and substrate temperature produced a film with relatively low structural heterogeneity while photoluminescence showed an order of magnitude increase in defect density for a similar change in the process.      

End-to-end coupling and network formation behavior of cylindrical block copolymer micelles with a crystalline polyferrocenylsilane core

Cylindrical block copolymer micelles with a crystalline poly(ferrocenyldimethylsilane) (PFDMS) core and a long corona-forming block are known to elongate through an epitaxial growth mechanism on addition of further PFDMS block copolymer unimers. We now report that addition of the semicrystalline homopolymer PFDMS(28) to monodisperse short (ca. 200 nm), cylindrical seed micelles of PFDMS block copolymers results in the formation of aggregated structures by end-to-end coupling to form micelle networks. The resulting aggregates were characterized by dynamic light scattering (DLS), transmission electron microscopy (TEM), and atomic force microscopy (AFM). In some cases, a core-thickening effect was also observed where the added homopolymer appeared to deposit and crystallize at the core-corona interface, which resulted in an increase of the width of the micelles within the networks. No evidence for aggregation was detected when the amorphous homopolymer poly(ferrocenylethylmethylsilane) (PFEMS(25)) was added to the cylindrical seed micelles whereas similar behavior to PFDMS(28) was noted for semicrystalline polyferrocenyldimethylgermane (PFDMG(30)). This suggested that the crystallinity of the added homopolymer is critical for subsequent end-to-end coupling and network formation to occur. We also explored the tendency of the cylindrical seed micelles to form aggregates by the addition of PI-b-PFDMS (PI = polyisoprene) block copolymers (block ratios 6:1, 3.8:1, 2:1, or 1:1), and striking differences were noted. The results ranged from typical micelle elongation, as reported in previous work, at high corona to core-forming block ratios (PI-b-PFDMS; 6:1) to predominantly end-to-end coupling at lower ratios (PI-b-PFDMS; 2:1, 1:1) to form long, essentially linear structures. The latter process, especially for the 2:1 block copolymer, led to much more controlled aggregate formation compared with that observed on addition of homopolymers.     

Microwave-assisted extractions of active ingredients from plants

Microwave-assisted extraction (MAE) is widely employed in the analysis and the extraction of active compounds from plants. This review summarizes the research done during the last decade on the MAE of active ingredients from plants. Advances and modifications to improve the performance of MAE are presented and discussed in detail. Modified MAE such as vacuum microwave-assisted extraction (VMAE), nitrogen-protected microwave-assisted extraction (NPMAE), ultrasonic microwave-assisted extraction (UMAE), dynamic microwave-assisted extraction (DMAE) and other advancements in MAE are also detailed in this article. In addition, the microwave extraction procedures and the important parameters influencing its performance are also included, together with the advantages and the drawbacks of each MAE techniques.     

Co3O4/SiO2 nanocomposites for supercapacitor application

In this study, Co₃O₄/SiO₂ nanocomposites have been successfully synthesized by citrate–gel method by utilizing SiO₂ matrix for Co₃O₄ embedment. Spectroscopy analyses confirm the formation of high crystalline Co₃O₄ nanoparticles; meanwhile, microscopy findings reveal that the Co₃O₄ nanoparticles are embedded in SiO₂ matrix. Electrochemical properties of the Co₃O₄/SiO₂ nanocomposites were carried out using cyclic voltammetry (CV), galvanostatic charge–discharge, and electrochemical impedance spectroscopy (EIS) in 5 M KOH electrolyte. The findings show that the charge storage of Co₃O₄/SiO₂ nanocomposites is mainly due to the reversible redox reaction (pseudocapacitance). The highest specific capacitance of 1,143 F g ^?1 could be achieved at a scan rate of 2.5 mV s^?1 in the potential region between 0 and 0.6 V. Furthermore, high-capacitance retention (>92 %) after 900 continuous charge–discharge tests reveals the excellent stability of the nanocomposites. It is worth noting from the EIS measurements that the nanocomposites have low ESR value of 0.33 Ω. The results manifest that Co₃O₄/SiO₂ nanocomposites are the promising electrode material for supercapacitor application.     

Nitrate, ascorbic acid, mineral and antioxidant activities of Cosmos caudatus in response to organic and mineral-based fertilizer rates

The source and quantity of nutrients available to plants can affect the quality of leafy herbs. A study was conducted to compare quality of Cosmos caudatus in response to rates of organic and mineral-based fertilizers. Organic based fertilizer GOBI (8% N:8% P?O?:8% K?O) and inorganic fertilizer (15% N, 15% P?O?, 15% K?O) were evaluated based on N element rates at 0, 30, 60, 90, 120 kg h?1. Application of organic based fertilizer reduced nitrate, improved vitamin C, antioxidant activity as well as nitrogen and calcium nutrients content. Antioxidant activity and chlorophyll content were significantly higher with increased fertilizer application. Fertilization appeared to enhance vitamin C content, however for the maximum ascorbic acid content, regardless of fertilizer sources, plants did not require high amounts of fertilizer.