Design Features of a Prompt Gamma Neutron Activation Analysis System at HANARO

The design features are described of a prompt gamma neutron activation analysis system at HANARO, a 30 MW research reactor in the Korea Atomic Energy Research Institute. The beam consists of polychromatic thermal neutrons diffracted by a set of pyrolytic graphite crystals at orders n in the range 1n6 at a Bragg angle of 45° on a horizontal beam line. A neutron flux of 1.0·10⁸ n·cm^–2·s^–1 is calculated at the sample position from the reflectivity of the crystal which has been confirmed in a measurement of a diffracted neutron spectrum using a time-of-flight spectrometer and gold-wire activation. The fast neutron and gamma backgrounds will be low due to the use of a diffracted beam and a tapered collimator. The detection system comprises a 30% n-type HPGe detector, signal electronics and a fast ADC. The first application of this system will be the analysis of boron concentration in biological samples for neutron capture therapy. Construction of the beam line and the arrangement of the detection system is proceeding.     

Operating characteristics and energy distribution in transferred plasma arc systems

A specially designed plasma chamber was constructed to study the operating characteristics of a dc plasma-transferred arc of argon, struck between a fluid convective cathode and a water-cooled anode. The arc voltage increased markedly with arc length and with an increase in the inlet velocity of the argon flow past the cathode tip, and much less with an increase in current. Radiation from the plasma column to the chamber walls and transfer of energy to the anode were the two principal modes of transfer of the arc energy. The former was dominant in the case of long arcs and at high inlet argon velocities. At the anode, the major contribution was from electron transfer, which occurred on a very small area of the anode (～5 mm in diameter). Convective heat transfer from the plasma was somewhat less. In all cases, the arc energy contributions to cathode cooling and to the exit gas enthalpy were small. From total heat flux and radiative heat transfer measurements, it was estimated that the plasma temperature just above the anode was in the range 10,000–12,000 K. Preliminary experiments with an anode consisting of molten copper showed that the arc root was no longer fixed but moved around continuously. The arc was othwewise quite stable, and its operating characteristics differed little from those reported for solid anodes, in spite of the greater extent of metal vaporization.     

Mimicry of tandem repeat peptides against cell surface carbohydrates

Our approach to multivalent peptide construction relies on tentacle peptides, also known as a multiple antigenic peptides, which contain two and four repeats of a selected peptide. In this communication, we report the results of preliminary studies aimed at (1) the selection of short peptides against the carbohydrate, sLeX, (2) the synthesis of tentacle dimers and tetramers of the selected peptides, and (3) the determination of affinities and specificities of the peptides to several related carbohydrates by using the surface plasmon resonance (SPR) and the equilibrium dialysis techniques. Binding affinity studies, as well as assays of in vitro binding of the peptides to a sLeX-specific cell line, have shown that the tetrameric peptides bind to the cell surface sugars.     

Colloidal lithographic nanopatterning via reactive ion etching

We report here a novel colloidal lithographic approach to the fabrication of nonspherical colloidal particle arrays with a long-range order by selective reactive ion etching (RIE) of multilayered spherical colloidal particles. First, layered colloidal crystals with different crystal structures (or orientations) were self-organized onto substrates. Then, during the RIE, the upper layer in the colloidal multilayer acted as a mask for the lower layer and the resulting anisotropic etching created nonspherical particle arrays and new patterns. The new patterns have shapes that are different from the original as a result of the relative shadowing of the RIE process by the top layer and the lower layers. The shape and size of the particles and patterns were dependent on the crystal orientation relative to the etchant flow, the number of colloidal layers, and the RIE conditions. The various colloidal patterns can be used as masks for two-dimensional (2-D) nanopatterns. In addition, the resulting nonspherical particles can be used as novel building blocks for colloidal photonic crystals.     

Determination of copper(II) in various samples by flame atomic absorption spectrophotometry after column preconcentration onto pulverized Amberlite XAD-4 loaded with N-benzoylphenylhydroxylamine

A sensitive technique for the determination of trace Cu(II) in various samples after column preconcentration by adsorbing onto pulverized Amberlite XAD-4 loaded with N-benzoylphenylhydroxylamine (BPHA) was developed. Several experimental conditions, such as the size of XAD-4, adsorption flow rate, pH of sample solution, and so forth, were optimized. The interfering effects of diverse concomitant ions were investigated. Al(III), Fe(III), Ni(II), and Co(II) interfered, but the interference by these ions was completely eliminated by adjusting the amount of XAD-4-BPHA resin to 0.30 g. The dynamic range, the correlation coefficient (R₂), and the detection limit obtained by the proposed technique were 1.0–60, 0.9953, and 0.83 ng/mL, respectively. For validating the technique, the aqueous samples (stream water, reservoir water, and wastewater), the diluted brass sample, and the plastic sample were used as real samples. Recovery yields of 94–102% were obtained. These measured data were not different from ICP-MS data at the 95% confidence level. This method was also validated by rice flour CRM (normal, fortified) samples. Based on the results of the experiment, it has been found that the proposed technique can be applied to the determination of Cu(II) in various real samples. The text was submitted by the authors in English.     

Tuning chirality of single-wall carbon nanotubes by selective etching with carbon dioxide

CO2 molecule chemisorbs selectively on the zigzag tube edge without an activation barrier, whereas it physisorbs on the armchair edge of nanotubes. In addition, carbon nanotubes can be etched by an adsorbed oxygen atom of CO2 molecule. From our results, we suggest a selective etching mechanism for tuning the chirality of the mass-produced carbon nanotubes.     

Depth distribution of239,240Pu and137Cs in soils of South Korea

Depth distribution of^239,240Pu and¹³⁷Cs in the soils of South Korea have been studied. The average accumulated depositions were estimated roughly to be 54.8±32.1 Bq·m^–2 for^239,240Pu, 1.6±1.0 Bq· ·m^–2 for²³⁸Pu and 1982.8±929.1 Bq·m^–2 for¹³⁷Cs. The activity ratios of^239,240Pu/¹³⁷Cs in soils were found to be in the narrow range of 0.0153 to 0.0364 with a mean value of 0.0230±0.006. The concentrations of^239,240Pu and¹³⁷Cs in soils decrease exponentially with increasing the soil depth. A significant correlation was found between the concentration of^239,240Pu and that of¹³⁷Cs. The activity ratios of^239,240Pu/¹³⁷Cs tend to increase slightly with increasing soil depth.     

Four New Lariciresinol‐Based Lignan Glycosides from the Roots of Rhus javanica var. roxburghiana

The four new lariciresinol‐based lignan glycosides, (?)‐lariciresinol 4′‐(6″‐O‐feruloyl‐β‐D ‐glucopyranoside) ( 1 ), (?)‐lariciresinol 4′‐(4″,6″‐di‐O‐feruloyl‐β‐D ‐glucopyranoside) ( 2 ), 5,5′‐dimethoxylariciresinol 4′‐(4″,6″‐di‐O‐feruloyl)‐β‐D ‐glucopyranoside) ( 3 ), and 4‐O‐[α‐(1,2‐dihydroxyethyl)syringyl]‐5,5′‐dimethoxylariciresinol 4′‐(4″,6″‐di‐O‐feruloyl‐β‐D ‐glucopyranoside) ( 4 ), together with two known ones, lariciresinol 4′‐β‐D ‐glucopyranoside) ( 5 ) and tortoside B ( 6 ), were isolated from the BuOH extract of Rhus javanica var. roxburghiana roots, and their structures were established by means of various spectroscopic techniques.     

Human immunoglobulin adsorption investigated by means of quartz crystal microbalance dissipation, atomic force microscopy, surface acoustic wave, and surface plasmon resonance techniques

Time-resolved adsorption behavior of a human immunoglobin G (hIgG) protein on a hydrophobized gold surface is investigated using multitechniques: quartz crystal microbalance/dissipation (QCM-D) technique; combined surface plasmon resonance (SPR) and Love mode surface acoustic wave (SAW) technique; combined QCM-D and atomic force microscopy (AFM) technique. The adsorbed hIgG forms interfacial structures varying in organization from a submonolayer to a multilayer. An "end-on" IgG orientation in the monolayer film, associated with the surface coverage results, does not corroborate with the effective protein thickness determined from SPR/SAW measurements. This inconsistence is interpreted by a deformation effect induced by conformation change. This conformation change is confirmed by QCM-D measurement. Combined SPR/SAW measurements suggest that the adsorbed protein barely contains water after extended contact with the hydrophobic surface. This limited interfacial hydration also contributed to a continuous conformation change in the adsorbed protein layer. The viscoelastic variation associated with interfacial conformation changes induces about 1.5 times overestimation of the mass uptake in the QCM-D measurements. The merit of combined multitechnique measurements is demonstrated.