Pit your wits against young minds!

This column is a place for those bits of contagious mathematics that travel from person to person in the community, because they are so elegant, suprising, or appealing that one has an urge to pass them on. Contributions are most welcome.     

Strategies for the development of a voltammetric sensor for the determination of hydrogen peroxide at high concentrations

Different strategies are presented for the development of a voltammetric sensor for in-line measurement and monitoring of H₂O₂ in high concentrations (up to 30 g/l) as used in textile bleaching systems. When using macroelectrodes, signal saturation is observed even at medium concentrations. Some improvement can be achieved by hydrodynamic electrodes like ring-disk electrodes. Satisfactory results up to the desired level in practical solutions (possessing only limited conductivity) are obtained with Pt-microelectrodes.     

Competitive influence of atactic polystyrene and supercritical carbon dioxide on the conformation of syndiotactic polystyrene

The crystallization behavior of miscible syndiotactic polystyrene (sPS) and atactic polystyrene (aPS) blends with different sPS/aPS weight ratios was investigated in supercritical CO₂ by using Fourier‐transform infrared spectroscopy, differential scanning calorimetry, and wide‐angle X‐ray diffraction. Supercritical CO₂ and aPS exhibited different effects on the conformational change of sPS and competed with each other. Increasing the content of amorphous aPS in the blends made its effect on the conformational change of sPS gradually surpass that of supercritical CO₂. Supercritical CO₂ favored the formation of the helical conformation of sPS in lower temperature range and the all trans planar conformation in higher temperature range, instead of forming the latter one only in higher temperature range in ambient atmosphere. However, increasing aPS content in the blends pushed the range for forming the helical conformation to lower temperature and made the all trans planar conformation dominant in aPS/sPS 25/75 blend after treating in supercritical CO₂ above 60 °C. The all trans planar zigzag conformation was more favorable than the helical conformation after mixing aPS in sPS in supercritical CO₂. © 2007 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 45: 1755–1764, 2007     

Synthesis and characterization of liquid crystalline side‐chain block copolymers containing luminescent 4,4′‐bis(biphenyl)fluorene pendants

A series of new liquid crystalline homopolymers, copolymers, and block copolymers were polymerized from styrene‐macroinitiator ( SMi ) and methacrylates with pendent 4,4′‐bis(biphenyl)fluorene ( M1 ) and biphenyl‐4‐ylfluorene ( M2 ) groups through atom transfer radical polymerization (ATRP). The number‐average molecular weights (Mn) of polymers P1 ‐ P4 were 10,007, 14,852, 6,275, and 10,463 g mol^?1 with polydispersity indices values of 1.21, 1.15, 1.31, and 1.22, respectively. All polymers exhibit the nematic phase. The thermal, mesogenic, and photoluminescent properties of all polymers were investigated. © 2007 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 45: 4564–4572, 2007     

Atomistic phenomena in dense fluid shock waves

The shock structure problem is one of the classical problems of fluid mechanics and at least for non-reacting dilute gases it has been considered essentially solved. Here we present a few recent findings, to show that this is not the case. There are still new physical effects to be discovered provided that the numerical technique is general enough to not rule them out a priori. While the results have been obtained for dense fluids, some of the effects might also be observable for shocks in dilute gases.     

Approximation of transient temperatures in complex geometries using fractional derivatives

It is shown that time-dependent temperatures in a transient, conductive system can be approximately modeled by a fractional-order differential equation, the order of which depends on the Biot number. This approximation is particularly suitable for complex shapes for which a first-principles approach is too difficult or computationally time-consuming. Analytical solutions of these equations can be written in terms of the Mittag-Leffler function. The approximation is especially useful if a suitable fractional-order controller is to be designed for the system.     

Interfacial dynamics‐based modelling of turbulent cavitating flows,Part‐2: Time‐dependent computations

The interfacial dynamics‐based cavitation model, developed in Part‐1, is further employed for unsteady flow computations. The pressure‐based operator‐splitting algorithm (PISO) is extended to handle the time‐dependent cavitating flows with particular focus on the coupling of the cavitation and turbulence models, and the large density ratio associated with cavitation. Furthermore, the compressibility effect is important for unsteady cavitating flows because in a water–vapour mixture, depending on the composition, the speed of sound inside the cavity can vary by an order of magnitude. The implications of the issue of the speed of the sound are assessed with alternative modelling approaches. Depending on the geometric confinement of the nozzle, compressibility model and cavitation numbers, either auto‐oscillation or quasi‐steady behaviour is observed. The adverse pressure gradient in the closure region is stronger at the maximum cavity size. One can also observe that the mass transfer process contributes to the cavitation dynamics. Compared to the steady flow computations, the velocity and vapour volume fraction distributions within the cavity are noticeably improved with time‐dependent computations. Copyright © 2004 John Wiley & Sons, Ltd.     

Damage and fracture evaluation of granular composite materials by digital image correlation method

This paper presents the applications of digital image correlation technique to the mesoscopic damage and fracture study of some granular based composite materials including steelfiber reinforced concrete, sandstone and crystal-polymer composite. The deformation fields of the composite materials resulted from stress localization were obtained by the correlation computation of the surface images with loading steps and thus the related damage prediction and fracture parameters were evaluated. The correlation searching could be performed either directly based on the gray levels of the digital images or from the wavelet transform (WT) coefficients of the transform spectrum. The latter was developed by the authors and showed higher resolution and sensitivity to the singularity detection. Because the displacement components came from the rough surfaces of the composite materials without any coats of gratings or fringes of optical interferometry, both surface profiles and the deformation fields of the composites were visualized which was helpful to compare each other to analyze the damage of those heterogeneous materials. The project supported by the National Natural Science Foundation of China (10125211 and 10072002), the Scientific Committee of Yunnan Province for the Program of Steel Fiber Reinforced Concrete, and the Institute of Chemical Materials, CAEP at Mianyang     

Crystallographic report: Crystal structure of a one‐dimensional zinc(II) coordination polymer containing 4,4′‐biphenyldicarboxylate hemihydrate

A one‐dimensional zinc(II) coordination polymer has been constructed from zinc(II), 4,4′‐biphenyldicarboxylate and pyridine in which each zinc(II) atom is coordinated by two pyridine ligands and two monodentate 4,4′‐biphenyldicarboxylate ligands that define a distorted tetrahedral geometry. Copyright © 2003 John Wiley & Sons, Ltd.