A fast method to measure the thickness of removed layer from etching of SSNTD based on EDXRF

Solid state nuclear track detectors are commonly used for measurements of concentrations of radon gas and/or radon progeny. All these measurements depend critically on the thickness of the removed layer during etching. However, the thickness of removed layer calculated using the etching period does not necessarily provide a sufficiently accurate measure of the thickness. For example, the bulk etch rate depends on the strength of stirring during etching for the LR 115 detector. We propose here to measure the thickness of the removed layer by using energy-dispersive X-ray fluorescence spectrometry. In the present work, a reference silver nitrate pellet is placed beneath the LR 115 detector, and the fluorescence X-ray intensity for silver is then measured. We have found a linear relationship between the X-ray intensity and the thickness of the removed layer for LR 115 detector. This provides a fast method to measure the thickness of removed layer from etching of LR 115 detector. However, this method was found to be inapplicable for the CR-39 detector. Therefore, alternative methods have yet to be explored for the CR-39 detector.     

Preparation and characterization of acrylic‐based black particles of poly(methyl methacrylate‐co‐ethylene glycol dimethacrylate) by dispersion polymerization for electrophoretic displays

Ultrafine black particles, ranging in diameter from 1 to 3 μm, were prepared by dispersion polymerization in a methanol/water mixture with vinyl monomers, nonpolymerizable Sudan black B dyes, and fluorescein isothiocyanate labeled charge control additives. Both the ratio of the methanol to the water dispersion medium and the polymeric stabilizer concentration had significant effects on the particle size. The important role of the stabilizer concentration lay in the particle formation step, during which it determined the particle stability and final particle size. These could affect the extent of the aggregation of nuclei by changing the adsorption rate of the stabilizer and the viscosity of the dispersion medium, resulting in smaller particles. The fluorescent‐labeled charge control additives strongly affected the electrophoretic mobility. A small concentration of fluorescent‐labeled charge control additives increased the electrophoretic mobility. However, a further addition reduced the electrophoretic mobility of the polymer particles. The concentration dependence of the fluorescent‐labeled charge control additives on the deposition behavior in the polymer particles was successfully imaged and thereafter quantified by image analysis. © 2004 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 5608–5616, 2004     

Thermal behavior of metallodendrimers possessing bis(terpyridinyl)Ru(II) connectivity and different surface functionality

A series of metallodendrimers, assembled by means of bis(terpyridinyl)Ru^(II) connectivity on poly(propylene imine) dendrimer scaffolds, with homogeneous or heterogeneous surfaces, were prepared. Differential scanning calorimetry and thermogravimetric analysis were used to determine their thermal behavior, glass‐transition temperatures, and the decomposition kinetics and temperatures; no synergy effects for these properties were observed for the heterogeneously surfaced constructs in contrast to the corresponding homogeneously coated materials, which exhibited different values depending on their surface functionalities. © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 1487–1495, 2004     

Electrospinning of ultrafine cellulose acetate fibers: Studies of a new solvent system and deacetylation of ultrafine cellulose acetate fibers

Electrospinning of cellulose acetate (CA) in a new solvent system and the deacetylation of the resulting ultrafine CA fibers were investigated. Ultrafine CA fibers (∼2.3 μm) were successfully prepared via electrospinning of CA in a mixed solvent of acetone/water at water contents of 10–15 wt %, and more ultrafine CA fibers (0.46 μm) were produced under basic pH conditions. Ultrafine cellulose fibers were regenerated from the homogeneous deacetylation of ultrafine CA fibers in KOH/ethanol. It was very rapid and completed within 20 min. The crystal structure, thermal properties, and morphology of ultrafine CA fibers were changed according to the degree of deacetylation, finally to those of pure cellulose, but the nonwoven fibrous mat structure was maintained. The activation energy for the deacetylation of ultrafine CA fibers was 10.3 kcal/mol. © 2003 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 5–11, 2004     

Time-resolved synchrotron X-ray study of crystalline phase transition in poly(aryl ether ketone ketone) containing alternated terephthalic/isophthalic moieties

Unique crystallization and melting behavior in poly(aryl ether ketone ketone) containing alternated terephthalic and isophthalic moieties were studied by time-resolved synchrotron x-ray methods. Recently, this material has been shown to exhibit three polymorphs (forms I, II, and III). In this work, we further investigated their distinctive thermal properties and found that form I is the dominating and the most thermally stable phase while form II is favored by fast nucleation conditions and is the least stable phase. On the other hand, form III represents a minor intermediate phase that usually coexists with form I and can be transferred from form II and to form I. Structural and morphological changes in form I have been followed by simultaneous wide-angle x-ray diffraction (WAXD)/small-angle x-ray scattering (SAXS) measurements during cold- or melt-crystallization and subsequent melting. In all cases, a larger dimensional change was found in the crystallographic a-axis than the b-axis during heating and cooling. This may be due to the greater lateral stress variation with respect to temperature along the a direction of the primary lamellae which is induced by either the formation of secondary lamellae or the preferential chain-folding direction in poly(aryl ether ketone ketone)s. During the phase transitions of form II ← III in the cold-crystallized specimen and form III ← I in the melt-crystallized samples, lamellar variables (long period, lamellar thickness, and invariant) obtained from SAXS remain almost constant. This indicates that the density distribution in the long spacing is independent of the melting in form II or III. For melt-crystallization, the corresponding changes in unit-cell dimensions and lamellar morphology during the annealing-induced low endotherm are most consistent with the argument that these changes are due to the melting of thin lamellar population. © 1995 John Wiley & Sons, Inc.     

Phase transformation of Ni-B, Ni-P diffusion barrier deposited electrolessly on Cu interconnect

In this paper, we report that the phase transformation of Ni-B, Ni-P diffusion barriers deposited electrolessly on Cu, for the reason that the Ni-P layer is a more effective diffusion barrier than the Ni-B layer. The Ni₃B crystallized was decomposed to Ni and B₂O₃ above 400 °C and the Ni₃P crystallized was decomposed to Ni and P₂O₅ above 600 °C respectively in Ar atmosphere. Also, the Ni₃B was decomposed to Ni and free B above 400 °C and the Ni₃P was decomposed to Ni and free P above 600 °C respectively in H₂ atmosphere. The decomposed Ni formed a solid solution with Cu. The Cu diffusion occurred above 400 °C for Ni-B layer and above 600 °C for Ni-P layer, respectively. Because the decomposition temperature of Ni-P layer is about 200 °C higher than that of Ni-B layer, the Ni-P layer is a more effective barrier for Cu than the Ni-B layer.     

Analysis of the manufacturing lead time in a production system with non-renewal batch input,threshold policy and post-operation

In this paper, we analyze the manufacturing lead time in a production system with BMAP (Batch Markovian Arrival process) input and post-operation operated under the N-policy. We use the factorization principle to derive the waiting time distribution (hence the manufacturing lead time) and the mean performance measures. A numerical example is provided.     

Electrochemical behavior of Li intercalation processes into a Li[NixLi(1/3−2x/3)Mn(2/3−x/3)]O2 cathode

Li[Ni_xLi_(1/3−2x/3)Mn_(2/3−x/3)]O₂ (X=0.17, 0.25, 0.33, 0.5) compounds are prepared by a simple combustion method. The Rietvelt analysis shows that these compounds could be classified as having the α-NaFeO₂ structure. The initial charge-discharge and irreversible capacity increases with the decrease of x in Li[Ni_xLi_(1/3−2x/3)Mn_(2/3−x/3)]O₂. Indeed, Li[Ni_0.50Mn_0.50]O₂ compound shows relatively low initial discharge capacity of 200 mAh/g and large capacity loss during cycling, with Li[Ni_0.17Li_0.22Mn_0.61]O₂ and Li[Ni_0.25Li_0.17Mn₀.₅₈]O₂ compounds exhibit high initial discharge capacity over 245 mAh/g and stable cycle performance in the voltage range of 4.8 -2.0 V. On the other hand, XANES analysis shows that the oxidation state of Ni ion reversibly changes between Ni²⁺ and about Ni³⁺, while the oxidation state of Mn ion sustains Mn⁴⁺ during charge-discharge process. This result does not agree with the previously reported ‘electrochemistry model’ of Li[Ni_xLi_(1/3−2x/3)Mn_(2/3−x/3)]O₂, in which Ni ion changes between Ni²⁺ and NI⁴⁺. Based on these results, we modified oxidation-state change of Mn and Ni ion during charge-discharge process.