Indeterminacy Criteria for the Stieltjes Matrix Moment Problem

In this paper, we obtain criteria for the indeterminacy of the Stieltjes matrix moment problem. We obtain explicit formulas for Stieltjes parameters and study the multiplicative structure of the resolvent matrix. In the indeterminate case, we study the analytic properties of the resolvent matrix of the moment problem. We describe the set of all matrix functions associated with the indeterminate Stieltjes moment problem in terms of linear fractional transformations over Stieltjes pairs.     

Polarization fluctuations in a dipolar medium in an electrostatic field

Radio Engineering and Electronics Institute, Academy of Sciences of the USSR. Translated from Izvestiya Vysshikh Uchebnykh Zavedenii, Radiofizika, Vol. 32, No. 9, pp. 1113–1124, September, 1989.     

用于机械振动实时监测的光纤光栅有源传感装置

把一对中心反射波长分别为1562.11nm和1562.71nm的光纤光栅粘贴在均质、等厚、等腰三角形悬臂梁上下表面作为环形腔光纤激光器端镜，当机械振动激励自由端时，通过观测激光输出脉冲，地施加于自由端的机械振动的频率进行了实时监测；观察两光栅波长漂移量差值的变化，可在0～6.1mm的范围内判断所测振动的振幅。低于100Hz时，实验结果与实际值基本吻合。     

Thermal conductivity of crystalline chrysotile asbestos

The thermal conductivity of crystalline chrysotile asbestos made up of hollow tubular Mg₃Si₂O₅(OH)₄ filaments is measured in the range 5–300 K. The paper discusses the possibility of using this material in studies of the thermal conductivity of thin filaments of metals and semiconductors incorporated into the channels of crystalline chrysotile asbestos tubes.     

Effect of ion impinging on the microstructure and field emission of carbon nanotubes

Effects of ion impinging on the microstructure and field electron emission properties of screen-printed carbon nanotube films were investigated. We observed that the plasma treatment modified the microstructure of CNTs along with the remarkable increase of emission site density. With the prolongation of ion impinging time, the emission current falls down first, and then rises up to higher than that of the untreated films. It is proposed that the change of emission characteristics is due to the different emission mechanisms. After the treatment, electrons are emitted predominantly from the nano-nodes on the tube wall instead from the nanotube tips.     

Crystallographic report: catena‐Aqua(2,2′‐bipyrimidine)lithium(I) perchlorate

A lithium(I) coordination polymer has been formed from LiClO₄ and the 2,2′‐bipyrimidine (bpym) ligand in which each square pyramidal lithium(I) atom is coordinated in the basal plane by four nitrogen donor atoms derived from two bpym ligands and one water molecule at the apical position. These are connected into a layer structure via hydrogen‐bonding interactions involving the perchlorate anions. Copyright © 2004 John Wiley & Sons, Ltd.     

The mechanism of emission in the red photoluminescence band of porous silicon

Porous silicon (PS) exhibits several photoluminescence (PL) bands, whose spectral position and intensity depend strongly on the actual conditions of preparation of PS, its treatment, and subsequent use. The PS PL band peaking at about 1.8 eV and usually assigned to the intrinsic emission of silicon nanocrystals was studied. It was shown that the temperature-induced variation of the PL kinetics in the 80 to 300-K interval follows a complex pattern and depends noticeably on the actual point on the band profile. The temperature behavior of PL decay in the 1.8-eV band is determined by the electron-hole recombination rate within a nanocrystal and the cascade carrier transitions from small to large nanocrystals, with an attendant decrease in energy.     

A fast method to measure the thickness of removed layer from etching of SSNTD based on EDXRF

Solid state nuclear track detectors are commonly used for measurements of concentrations of radon gas and/or radon progeny. All these measurements depend critically on the thickness of the removed layer during etching. However, the thickness of removed layer calculated using the etching period does not necessarily provide a sufficiently accurate measure of the thickness. For example, the bulk etch rate depends on the strength of stirring during etching for the LR 115 detector. We propose here to measure the thickness of the removed layer by using energy-dispersive X-ray fluorescence spectrometry. In the present work, a reference silver nitrate pellet is placed beneath the LR 115 detector, and the fluorescence X-ray intensity for silver is then measured. We have found a linear relationship between the X-ray intensity and the thickness of the removed layer for LR 115 detector. This provides a fast method to measure the thickness of removed layer from etching of LR 115 detector. However, this method was found to be inapplicable for the CR-39 detector. Therefore, alternative methods have yet to be explored for the CR-39 detector.     

Accuracy analysis of airborne gravimeter calibration using repeated flight paths

Some possible errors in determining the gravity anomalies are discussed. Such errors may be caused by an inaccurate calibration of the gravimeter used in an airborne survey system. An approach based on wavelet decompositions is proposed for its additional calibration with the use of flight data obtained during repeated flights.     

A quality criterion for visual tracking during nystagmus

The aim of this study is to construct a quantitative characteristic for the degree of gaze stabilization on a visual target with consideration of physiological constraints. A quality criterion for visual tracking during optokinetic vestibulocervical nystagmus is proposed. The index of imaginary tracking during rotation in the dark allows one to speak of a difference in the image stabilization quality between a healthy person and a patient. Experimental nystagmus data are used to calculate the quality index of visual tracking and the index of imaginary tracking.