Chromism of soluble polythienylenes

Thermochromism and solvatochromism of solutions of poly(3-alkylthienylenes) are reported. The experimental results indicate the presence of two coexisting phases: polymer in solution and polymer in microcrystalline aggregates. From the concentration independence of the thermochromism, it is concluded that the transition is fundamentally driven by a single chain mechanism, and that the aggregation (microcrystallization) of the poly(3-alkylthienylene) macromolecules can occur only after the single chain conformational change has occurred.     

Characteristics of a liquid/liquid optical waveguide using sheath flow and its application to detect molecules at a liquid/liquid interface.

The formation conditions and characteristics of a liquid/liquid optical waveguide (LLW) were studied using a two-phase sheath flow, where the inner organic phase flow acted as the core and the outer aqueous flow acted as the clad. In immiscible solvent systems, i.e., toluene/water and diethyl ether/water systems, the LLWs were formed in the range of higher than ca. 600 of the Reynolds number (Re), where the linear velocity of the organic solvent was much higher than that of the aqueous solution. On the other hand, in a miscible solvent system, i.e., a tetrahydrofuran/water system, a stable LLW was formed in the range of a much lower Re than in immiscible systems. Moreover, the molecules at the toluene/water interface of the LLW were observed with both fluorescence and absorbance measurement systems. In particular, the change in the fluorescence spectrum of 1-anilino-8-naphthalenesulfonate (ANS) at the interface within 1 ms was observed by this method, indicating the usefulness of the LLW for a fast kinetic study of a liquid/liquid interface.     

Determination of chromium, copper and lead in river water by graphite-furnace atomic absorption spectrometry after coprecipitation with terbium hydroxide.

Coprecipitation with terbium hydroxide quantitatively recovered trace amounts of chromium(III), copper(II) and lead(II) at pH 8.4 - 10.8, 8.0 - 11.5 and 8.7 - 11.5, respectively. The precipitate was dissolved in 0.85 mol dm(-3) nitric acid, and the analytes were determined by graphite-furnace atomic absorption spectrometry (GF-AAS). The presence of terbium (up to 7 g dm(-3)) did not interfere with the determination. The detection limits were 0.3 microg dm(-3) for chromium, 0.4 microg dm(-3) for copper and 0.5 microg dm(-3) for lead, when the analytes in 200 cm3 of the sample solution were concentrated into 10 cm3. The ions added to river or seawater were quantitatively recovered. Chromium and copper in a contaminated river water were successfully determined.     

A new dual-type DMA for measuring nanoparticles emitted from combustion engines

A new dual-type differential mobility analyzer (dual-type DMA) was developed in order to detect transient number concentrations of airborne nanoparticles with diameters centralized at around 10 nm (for nuclei mode particles) and 100 nm (for accumulation mode particles) in automobile exhaust gas. The apparatus divides the gas sample into two parts, and each part is sent through one of two coaxially nested sections for analysis. For the scanning mode measurement, the nanoparticles are charged by ²⁴¹Am and their size distributions are determined by varying the applied voltage over 2 min. The transient mode measurement, on the other hand, fixes the voltages for the two sections at peaks near 10 and 100 nm in order to monitor the transient behavior of the exhaust nanoparticles. The measurement principles and design of the dual-type DMA are detailed and the results for time response experiments are presented using model nanoparticles charged by a corona charger. The transient concentrations of the nuclei mode and the accumulation mode particles from a diesel engine were shown to be detected by this method, when ²⁴¹Am was used for charging the particles.     

Synthesis and properties of π‐conjugated dithiafulvene oligomers by addition of a monofunctionalized compound

Dithiafulvene oligomers ( 3 ) were prepared by cycloaddition polymerization of aldothioketenes with their alkynethiol tautomers derived from 1,4‐diethynylbenzene ( 2 ) with the addition of 1‐ethynyl‐4‐methylbenzene ( 1 ) as a monofunctionalized compound. Different feed ratios of 2 / 1 were used to control the molecular weights of 3 . The structures of 3 were confirmed by IR and ¹H NMR spectroscopies in comparison with those of 2‐(4‐tolylidene)‐4‐tolyl‐1,3‐dithiol ( 4 ) as a model compound, which was obtained by the treatment of lithium 2‐tolylethynethiolate with water in Et₂O. The number‐average degree of polymerization (DP) and the number‐average molecular weight were measured by gel permeation chromatographic and ¹H NMR analysis. DP increased with an increasing feed ratio of 2 / 1 . The ultraviolet–visible spectra of 3 in diluted acetonitrile showed that the absorption maxima of 3 increased with an increasing DP of 3 . These redshifts are ascribed to an effective expansion of the π‐conjugation system in 3 . The oligomers exhibited a maximum conjugation length of seven repeating units. The redox properties of 3 were examined by cyclic voltammetry. The oxidation half‐peak potentials (E_p/2) of 3 were slightly cathodically shifted with increasing DP. © 2003 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 41: 708–715, 2003     

Finding of Optimal Calcium Ion Probes for Fluorescence Lifetime Measurement

We have investigated the fluorescence lifetime properties of 8 calcium ion probes, calcium-green-1, calcium green-2, calcium green-5N, calcium orange, oregon green 488 BAPTA-6F, fluo-3, fluo-4, and fluo-5N. We found that the decay time of calcium green-5N varied more sensitively with calcium concentration than calcium green-1 which was known to be a highly sensitive probe. We have also found that the center of observable range of calcium concentration by fluorescence lifetime measurement is lower than that by fluorescence intensity measurement.     

Internal tissue displacement measurement based on ultrasonic wave Doppler signal digital detection and its application to fetal movement monitoring

We have developed a fetal movement monitoring system based on small displacement measurement of internal tissues. When ultrasonic pulses are transmitted to the fetus, the reflected ultrasonic waves which have a Doppler frequency shift due to the fetal movements are detected by using an ultrasonic pulsed Doppler technique. In this paper, we propose a displacement measurement method for internal tissues which is based on the Doppler signal digital detection technique. In the method, the received ultrasonic RF signals are sampled with a sampling frequency of four times higher than the centre frequency of the ultrasonic waves; the Doppler frequency shift signals are derived using digital signal processing. From the detected signals, the internal displacements are estimated using the arc-tangent method. The basic algorithm of the detection method has already been used in the area of blood flow sensing, however, we apply the algorithm to the displacement measurement of internal tissues. The comparison between the proposed method and the conventional method is presented. The fetal movement quantitative monitoring system based on the method which has been constructed is shown.