风速分布形状对空调中翅片管蒸发器性能的影响

通过建立空调蒸发器分布参数模型,并对模型进行了验证,进而研究了四种不同风速场对R22和R290翅片管蒸发器流动和换热性能的影响规律。研究表明:在上三角型、下三角型和三角型风速场分布下,蒸发器单位面积换热量、质量流量以及压降均较均匀风速场降低;上三角型较均匀型单位面积换热量下降达7%左右,下三角型和三角型较均匀型下降4%左右;在不同风速场下,各换热温差基本持平,总传热系数起主导作用;R290质量流量均较R22小40%左右,且压降均较R22小24%左右。在满足换热量的要求下,R290在协调压降与质量流量具有一定的优势,可以作为现有空调制冷剂R22的环保型替代工质。     

A tilted pad thrust slider bearing improved by the boundary slippage

The present paper proposes a new type of hydrodynamic lubricated tilted pad thrust slider bearing which is augmented with the boundary slippage at the stationary contact surface in the inlet zone. This design is of purpose to reduce the friction coefficient but increase the load-carrying capacity of the bearing. A theoretical analysis is presented for this bearing. Computational results and design guides for this bearing are given. It is found that the most increase of the carried load of the bearing by the boundary slippage is around 30 %, while the most reduction of the friction coefficient of the bearing by the boundary slippage is more than 40 %. This advantage is reached when the boundary slippage zone occupies 80 % of the bearing lubricated area and the fluid-contact interfacial shear strength at the boundary slippage interface is very low.     

基于苯乙烯腈结构的可逆力致变色化合物的合成及性能

合成了一种棒形的化合物4,4'-二(α-腈基-4-苯丙氧基苯乙烯)联苯(Ben-DCSB), 利用核磁共振(NMR)、质谱(EI-MS)、傅里叶变换红外光谱(FT-IR)和元素分析等对其进行了结构表征. 对Ben-DCSB重结晶粉末进行研磨后, 其发光颜色从蓝绿色变成黄绿色, 荧光量子效率(Φ_F)从初始的52.7%变为38.7%, 表明该化合物具有力致变色性质. 扫描电子显微镜(SEM)、X-射线衍射(XRD)和荧光寿命等测试结果显示, 这种现象是由于在外界环境刺激下改变了Ben-DCSB在聚集态下的分子堆积结构所造成的. 研磨后的样品暴露在溶剂蒸气(乙醇、二氯甲烷、四氢呋喃或丙酮)或100 ℃温度下放置2 min又能转换回初始状态的蓝绿色荧光, 表明化合物研磨后的样品具有气致和热致变色性能, 且展现出可逆变色性能. 对该化合物进行多次“力-溶剂蒸气刺激”和“力-热刺激”循环实验, 结果显示其具有很好的荧光可逆转换性能. 热分析结果显示化合物Ben-DCSB在194 ℃和212 ℃间存在向列相(纹影织构)的液晶态; 其热分解温度为362 ℃, 表明该化合物具有较好的热稳定性.     

Hydrodynamic lubrication in fully plastic asperity contacts

A line contact inlet zone analysis is carried out for the hydrodynamic lubrication in a fully plastic asperity contact. A governing equation of the central film thickness i.e. the film thickness in the fully plastic contact area is derived. An equation predicting this film thickness is also derived. It is found that for the fully plastic contact, under relatively light loads the prediction accuracy for the central film thickness is good, while at the load heavy enough the prediction equation greatly overestimates the central film thickness and the central film thickness solved from the analytical governing equation is significantly low showing the asperity in boundary layer lubrication. For the fully plastic contact, the central film thickness is nearly half of that obtained based on the elastic contact assumption for relatively light loads or even lower for heavier loads. The hydrodynamic lubrication is found difficult to form in the fully plastic asperity contact for the carried load heavy enough or the significantly low sliding speed between the asperities. To achieve a high hydrodynamic lubrication film thickness in the fully plastic asperity contact it is recommended to employ a high sliding speed or a high fluid viscosity. However, in the fully plastic asperity contact, the potential hydrodynamic load-carrying capacity is limited and much smaller than that based on the elastic contact assumption or predicted by conventional line contact elasto-hydrodynamic lubrication theory.     

Infrared small moving target detection method based on graph matching

We apply graph matching method to detect infrared small moving targets using image sequences. Candidates （interest points） detected in the first frame form one graph and the same candidates in the last frame form another one. The real moving targets are extracted by matching these two graphs. Experimental results demonstrate that the proposed method is robust and efficient to the translation and rotation of the background.     

基于FPGA的储存环束流轨道联锁系统设计

上海光源储存环束流轨道联锁系统是加速器机器联锁保护系统(MPS)的重要组成部分,针对日常供光和机器研究的需求,需要对束流位置测量系统前各Libera电子学输出的联锁信号进行标记,以区分联锁信号的先后顺序和误报的联锁信号,同时触发所有Libera电子学前锁存逐圈(TBT)数据。新的联锁系统将所有联锁信号通过光纤传输汇总至FPGA数据采集板卡进行甄别,并将该系统集成储存环EPICS控制系统中。实验室测试显示该系统能够能够分辨数十ns范围内模拟的联锁信号,同时输出特定的触发信号至对应的Libera电子学,表明该系统达到设计要求。     

用束流位置监测器测量上海光源束流寿命

通过理论分析研究了电磁耦合型束流位置探测器（BPM）用于束流寿命测量的可行性,并在上海光源储存环上进行了束流实验,对其性能进行了评估。实验结果表明,与目前常用的直流流强变压器（DCCT）系统相比,BPM给出的束流寿命具有更高的带宽和分辨力,有利于进行不同时间尺度的束流寿命评估,而且可以通过多个平均的方式来进一步提高测量精度。     

Boundary film shear elastic modulus effect in hydrodynamic contact. Part II: influence of operational parameters

The present paper is the subsequent research of the first part (Theor Comput Fluid Dyn, 2009). It investigates the boundary film shear elastic modulus effect in a hydrodynamic contact in different operating conditions. The hydrodynamic contact is one-dimensional, composed of two parallel plane surfaces, which are respectively rough rigid with rectangular micro projections in profile periodically distributed on the surface and ideally smooth rigid. The whole contact consists of cavitated area and hydrodynamic area. The hydrodynamic area consists of many micro Raleigh bearings which are discontinuously and periodically distributed in the contact. The hydrodynamic contact in a micro Raleigh bearing consists of boundary film area and fluid film area which, respectively, occur in the outlet and inlet zones. In boundary film area, the film slips at the upper contact surface due to the limited shear stress capacity of the film–contact interface, while the film does not slip at the lower contact surface due to the shear stress capacity of the film–contact interface large enough. In boundary film area, the viscosity, density, and shear elastic modulus of the film are varied across the film thickness due to the film–contact interactions, and their effective values are used in modeling which depends on the film thickness. In fluid film area, the film does not slip at either of the contact surfaces, and the shear elastic modulus of the film is neglected. It is found from the simulation results that the boundary film shear elastic modulus influences are normally negligible on the mass flow through the contact, the carried load of the contact and the overall film thickness of the contact, and the boundary film shear elastic modulus would normally influence the local film thickness in an elastic contact when the local film thickness is on the film molecule diameter scale. It is also found that the boundary film shear elastic modulus effect has the tendency of being increased with the reduction of the width of a micro contact. It is increased with the reduction of the boundary film–contact interfacial shear strength or with the increase of the critical boundary film thickness, while it is strongest at certain values of the contact surface roughness, the width ratio of fluid film area to boundary film area, and the lubricant film shear elastic modulus.

---

     

强外电场作用下二甲基硅酮的分子结构和激发态

The ground states of dimethyl siloxane under different intense electric fields ranging from - 0. 04 to 0. 04 a. u. are optimized using density functional theory DFT / B3P86 at 6-311 ++ G（d,p）level. The excitation energies and oscillator strengths under the same intense applied electric fields are calculated employing the revised hybrid CIS-DFT method. The result shows that the electronic state,molecular geometry,total energy,dipole moment and excitation energy are strongly dependent on the field strength and behave asymmetry to the direction of the applied electric field. As the electric field changes from - 0. 04 to 0. 04 a. u. ,the bond length of Si-O increases whereas the bond length of Si-C decreases because of the charge transfer induced by the applied electric field. The dipole moment of the ground state decreases linearly with the applied field strength. However,the dipole moment of molecule changes from positive to negative as the inverse electric field increase to - 0. 03 a. u. Further increase of the inverse electric field results in an increase of the total energy of the molecule. The dependence of the calculated excitation energies on the applied electric field strength is fitting well to the relationship proposed by Grozema. The excitation energies of the first five excited states of dimethyl siloxane decrease as the applied electric filed increases because the energy gap between the HOMO and LUMO become close with the field,which shows that the molecule is easy to be excited under electric field and hence can be easily dissociated.     

基于双面质点振速测量的声场分离技术

现有的声场分离技术或是基于双面声压测量或是基于单面声压和质点振速测量。本文以二维空间傅里叶变换法作为声场分离算法,提出一种基于双面质点振速测量的声场分离技术。论文首先推导出了该方法的理论模型,随后通过仿真研究验证了该方法的有效性,并通过与基于双面声压测量的声场分离方法的比较说明了其优越性。结果表明:采用基于双面质点振速测量的声场分离方法可以有效实现声场分离;基于双面质点振速测量的声场分离方法可以获得更高的质点振速分离精度,而基于双面声压测量的声场分离方法可以获得更高的声压分离精度。