Experimental investigation on a software synchronous optical sampling technique based on periodically poled lithium niobate

A software synchronous optical sampling system is constructed based on sum frequency generation (SFG) in periodically poled lithium niobate (PPLN). Five gigahertz of a non-return-to-zero (NRZ) data signal is sampled by sampling pulse with the repetition frequency of 29.31 MHz. The power of the SFG light is set at 23 dBm, and an eye diagram is successfully recovered. A band-pass filter is added before the sampling pulse is subjected to erbium-doped fiber amplifier to reduce gain competition and ensure a high power level of SFG.     

Efficient continuous-wave eye-safe region signal output from intra-cavity singly resonant optical parametric oscillator

We report an efficient continuous-wave (CW) tunable intra-cavity singly resonant optical parametric oscillator based on the multi-period periodically poled lithium niobate and using a laser diode (LD) end-pumped CW 1064 nm Nd:YVO₄ laser as the pump source. A highly efficiency CW operation is realized through a careful cavity design for mode matching and thermal stability. The signal tuning range is 1401-1500 nm obtained by varying the domain period. The maximum output power of 2.2 W at 1500 nm is obtained with a 17.1 W 808 nm LD power and the corresponding conversion efficiency is 12.9%.     

多孔脆性介质冲击波压缩破坏的细观机理和图像

本文采用一种具有良好定量性质的离散元模型研究了带孔洞的各向同性脆性介质在细观尺度上的压缩破坏特征. 通过对孤立孔洞、三种简单的孔洞排布方式和大量孔洞随机排布等几种情况的模拟, 认识到了剪切破坏和局域拉伸破坏是冲击波压缩下多孔介质的基本破坏模式; 孔洞之间的损伤贯通会促进孔洞在较低应力下发生塌缩, 但损伤区的应力松弛过程却会对一定范围内的介质起到损伤屏蔽作用; 不同区域中损伤促进和损伤屏蔽的综合效果是在多孔脆性介质中形成一种高损伤区与低损伤区间错排布的奇特损伤分布. 本文的研究结果为深入理解脆性材料冲击波压缩破坏的演化过程和机理提供了细观尺度上的初步物理图像.     

窗口可变滑动相关分析方法在激光诱导击穿光谱谱线自动识别中的应用

激光诱导击穿光谱(LIBS)谱线具有很窄的展宽,且光谱仪因外界温度条件的变化存在波长漂移,光谱数据为离散数字信号,受噪声、谱线重叠及连续背景的影响,信号存在失真和变形。而目前光谱仪自带谱线识别分析软件主要以"就近原则"为主,错误率较高,必须依赖于人眼的观察对比。针对这个问题,在研究LIBS光谱特性的基础上,提出了一种窗口可变滑动相关分析方法(CAASW),用于激光诱导击穿光谱谱线自动识别。以土壤标准物质为样品,对该方法进行了实验分析和评价,与光谱仪自带分析识别软件相比,CAASW明显提高了识别准确率和识别速度,最终实现了谱线的自动识别。     

W波段交错双栅返波振荡器高频系统

将矩形交错双栅结构作为慢波电路并提出与之配套的过渡结构和输出耦合器,设计了利用带状电子注工作在W波段的返波振荡器。提出的过渡结构和耦合器解决了该类直波导型器件的信号传输衰减大、反射强等难题。相对于传统圆形电子注器件,该器件得到了较大的功率提升。利用三维粒子模拟计算的方法,在电流12 mA时通过调节工作电压,在92~98 GHz频带内得到了数W的稳定平均功率输出,信号中心频率非常接近设计频率,且单色性好,谐波分量小。     

用于诊断纳秒脉冲电流的微分环现场标定技术

分析了用于纳秒脉冲电流测量的微分环标定难点,提出微分环现场标定方法。通过脉冲形成线脉冲充电以解决微分环标定中信噪比较低、可信度较差等问题;分析了脉冲形成线充电时间、充电电压及脉冲形成开关击穿电压等回路参数对标定结果的影响。基于闪光二号加速器,对测量二极管电流的微分环进行了现场标定,前级隔离开关平均击穿电压为25 kV时,微分环标定回路电流达到1.3 kA,微分环灵敏度为9.311010,方差为0.151010。     

火花通道长度对激光触发开关特性的影响

利用超高速相机,在曝光时间100 ns时,对不同能量下激光在氮气气体开关中形成的火花通道进行拍照,得到了不同焦距下激光波长266 nm时激光火花通道长度与激光能量的关系。开展了激光触发气体火花开关的实验研究,激光触发开关延时、抖动随激光能量的增加而减小。将火花通道长度与激光触发开关的特性进行了分析,气体开关的抖动随着激光火花通道长度的增加而减小,当火花通道沿电极间轴向长度达到开关电极间距40%时,开关的抖动为亚ns量级。     

Study on information content of the 3D object's coherent imaging and hologram information redundancy

On the basis of the light field distribution of objects with coherent illumination, and the most basic physical mechanism of binocular stereoscopic vision, we calculate the information content of the light field in ‘the smallest observation window’ produced by a point source and multi-points source respectively, and ‘the smallest observation window’ means that the size of the window just satisfies the demand of binocular stereo vision. As a result, the minimum information content of the light field that the binocular stereo vision needed is acquired. Comparing the information content of hologram with that of the light field in the hologram plane, we make out the redundancy of holographic information content and point out the direction of the holographic compression.     

Controlled decoherence of three-level rf-SQUID qubit with asymmetric potential

A scheme is proposed to controll the decoherence of three-level rf-SQUID qubit with asymmetric potential by designing an external electric circuit for superconductive flux qubit. The results show that it may not only raise the gate speed but also extend decoherence time for a three-level structure.     

Preparation and Mechanical Properties of Fe3Al Nanostructured Intermetallics

Nanostructured Fe₃Al intermetallic compounds were produced by using hydrogen arc plasma method. The transmission electron microscopy experiments showed that the average particle size of the as-synthesized was about 40-nm. The change in hardness of Fe₃Al nanostructured intermetallic compounds with annealing temperatures was observed and evaluated.