氢化丁苯共聚物结构的核磁共振波谱表征Ⅱ.微观结构的定量计算

在氢化丁苯共聚物¹³C-NMR谱脂肪碳部分谱带归属的基础上,根据各谱带的主要来源,推导出六个二单元浓度的计算公式。计算出二单元、一单元的相对含量,各结构单元的数均序列长度、嵌段含量和其它结构参数。加氢前后的¹H-和¹³C-NMR谱的组成计算结果基本一致。初步探讨了作为粘度指数改进剂的氢化丁苯共聚物微观结构与性能的关系,为合成提供了依据。     

一类几乎最优循环图{C_p(m,m+1,p/a)}

本文比较了循环图类{c_p(n_1,…,n_p)}和{c-p(n_1…,n_p,p/α)}的直径下界。对于p和α满足一定条件的循环图类{c_p(n_1,n_2,p/α)},本文给出了达到或几乎达到此图类直径下界的一类几乎最优循环图{c_p(m,m+1,p/α)}。     

双轴晶体Nd^3＋：KGd（WO4）2的非偏振吸收光谱研究

报道了用三个方向相互垂直的非偏振吸收光谱测量计算Ｊｕｄｄ－Ｏｆｅｌｔ参数从而算出双轴晶体Ｎｄ３＋ＫＧｄ（ＷＯ４）２的荧光寿命、荧光分支比和发射截面的方法。得到的荧光寿命为１１９μｓ，平均发射截面为２．３×１０－１９ｃｍ２。     

离子束引起的在Al／Cr双层薄膜界面处的原子混合

用600keV的Kr~ 离子轰击Al/Cr双层薄膜样品进行界面原子反应及相互混合的研究。实验样品是在单晶硅上蒸镀约500nm厚的铝膜,相继再蒸上所需厚度的铬膜而制成的。轰击剂量为2.0×10~(15)-2.5×10~(16)Kr~ /cm~2。用2.0MeVa粒子对轰击前后的样品进行了卢瑟福背散射(RBS)分析,发现界面处有明显的原子混合存在;当轰击剂量≥1.0×10~(16)Kr~ /cm~2时,RBS谱出现有明显的坪台,经拟合计算和x射线衍射(XRD)测量证实确有化合物Al_(13)Cr_2存在;还分别得到了原子混合量及混合效率与轰击剂量的关系;最后对界面处的原子混合机制进行了讨论。     

Polymerization of cyclopentadiene initiated by methylaluminoxane

The polymerization of cyclopentadiene (CPD) was effectively initiated by methylaluminoxane (MAO) to generate poly(cyclopentadiene) (polyCPD). The effects on the polymerization of some reaction parameters such as the monomer concentration, the initiator concentration, and solvents were investigated. The conversion of CPD was monitored with gas chromatography to investigate the reaction kinetics. The polymerization rate was proportional to the concentrations of MAO in the first order and of the CPD monomer in the second order, and a reasonable cationic polymerization mechanism was suggested on the basis of the kinetic study. PolyCPD obtained at a low temperature could be dissolved in toluene or chloroform, and this indicated lower cross‐coupling during the polymerization reaction. ¹H NMR and IR analysis of the polymer indicated that there were almost equal amounts of 1,2‐enchainment and 1,4‐enchainment in the polymer chain. The measurement of polyCPD showed its unique properties as a potential candidate for stable wrappings or electronic packaging materials. © 2005 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 264–272, 2006     

A copper‐based reverse atom‐transfer radical polymerization process for the living radical polymerization of polyacrylonitrile

The reverse atom‐transfer radical polymerization (RATRP) technique using CuCl₂/2,2′‐bipyridine (bipy) complex as a catalyst was applied to the living radical polymerization of acrylonitrile (AN). A hexasubstituted ethane thermal iniferter, diethyl 2,3‐dicyano‐2,3‐diphenylsuccinate (DCDPS), was firstly used as the initiator in this copper‐based RATRP initiation system. A CuCl₂ to bipy ratio of 0.5 not only gives the best control of molecular weight and its distribution, but also provides rather rapid reaction rate. The rate of polymerization increases with increasing the polymerization temperature, and the apparent activation energy was calculated to be 57.4 kJ mol^?1. Because the polymers obtained were end‐functionalized by chlorine atoms, they were used as macroinitiators to proceed the chain extension polymerization in the presence of CuCl/bipy catalyst system via a conventional ATRP process. © 2005 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 226–231, 2006     

Synthesis of polyacrylonitrile via reverse atom transfer radical polymerization catalyzed by FeCl3/isophthalic acid

FeCl₃ coordinated by isophthalic acid was first used as a catalyst in the azobisisobutyronitrile‐initiated reverse atom transfer radical polymerization of acrylonitrile. N,N‐Dimethylformamide was used as a solvent to improve the solubility of the ligand. An FeCl₃‐to‐isophthalic acid ratio of 0.5 not only gave the best control of the molecular weight and its distribution but also provided rather a rapid reaction rate. The effects of different solvents on the polymerization of acrylonitrile were also investigated. The rate of the polymerization in N,N‐dimethylformamide was faster than that in propylene carbonate and toluene. The molecular weight of polyacrylonitrile agreed reasonably well with the theoretical molecular weight in N,N‐dimethylformamide. The rate of polymerization increased with increasing polymerization temperature, and the apparent activation energy was calculated to be 59.9 kJ mol^?1. Reverse atom transfer radical polymerization was first used to successfully synthesize acrylonitrile polymers with a molecular weight higher than 80,000 and a narrow polydispersity as low as 1.22. © 2005 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 219–225, 2006     

准直小孔法自动调焦在激光直写入系统中的应用

本文介绍了一种新的自动调焦方法准直小孔法.对自动调焦的原理和后继电路处理方法作了详细的分析.它具有响应时间短、灵敏度高,能够很好的在激光直接写入系统中克服物镜工作台运动中导轨的不平和轴向窜动所造成的离焦。     

The global topological meaning of cocycles in a Gauge group

This Letter shows explicitly that the descent sequence of cocycles in a gauge group realizes the ech-de Rham double complex. Meanwhile the ech complex corresponds to finite gauge transformations. This Letter also shows how the indices of each order of cocycles characterizes the obstructions on overlapping spheres in different dimensions and how these indices are equal to a common one.     

Analytical solutions of the lattice Boltzmann BGK model

Analytical solutions of the two-dimensional triangular and square lattice Boltzmann BGK models have been obtained for the plane Poiseuille flow and the plane Couette flow. The analytical solutions are written in terms of the characteristic velocity of the flow, the single relaxation time , and the lattice spacing. The analytic solutions are the exact representation of these two flows without any approximation. Using the analytical solution, it is shown that in Poiseuille flow the bounce-back boundary condition introduces an error of first order in the lattice spacing. The boundary condition used by Kadanoffet al. in lattice gas automata to simulate Poiseuille flow is also considered for the triangular lattice Boltzmann BGK model. An analytical solution is obtained and used to show that the boundary condition introduces an error of second order in the lattice spacing.