Study on viscoelastic properties of epoxidized trans-1,4-polyisoprene by rubber process analyzer

Two kinds of epoxidized trans-1,4-polyisoprene (ETPI) were prepared by surface selective epoxidation which products named as SETPI and solution random epoxidation which product named as RETPI, respectively. The viscoelastic behavior of unmodified trans-1,4-polyisoprene (TPI) and ETPI, both RETPI and SETPI, was studied with the use of a rubber process analyzer (RPA). The strain sweep, frequency sweep, temperature sweep and stress sweep indicated that the SETPI could be seen as a blend of the pure ETPI and TPI. The rheological behavior of TPI and ETPI was recorded by two kinds of shear rate. An obvious effect of epoxidation on the movement behavior of the melt of RETPI was observed. However, the effect of epoxy content of SETPI on ln??* is weak. The complex viscosity at various frequencies of SETPI is higher than that of RETPI.     

Synthesis and characterization of fluorine-containing cholesteric liquid crystalline polysiloxanes bearing trifluoromethyl-substituted mesogens

A series of side-chain liquid crystal (LC) polysiloxanes were synthesised with Poly(methylhydrogeno)siloxane, 4?-(undec-10-enoyloxy) biphenyl – 4 – yl 4- (trifluoromethyl) benzoate (M_th) and a chiral nematic (N*) LC monomer 1-allyl 10-(cholesteryl)-decanedioate (M_ch). The chemical structures and LC properties of the monomers and polymers were characterised by FTIR, ¹H-NMR, differential scanning calorimetry, thermogravimetric analysis, POM and X-ray diffractometer. M_ch is monotropic N* LC. The homopolymer derived from monomer M_ch is enantiotropic N* LC. Monomer M_th is a smectic A liquid crystal. The copolymers derived from M_ch and M_th are N* LCs. The temperatures at which 5% weight loss occurred are greater than 300°C for all the fluoro-containing polymers, and the residue weights of the samples at 600°C increased slightly as the content of trifluoromethyl mesogens increased in the polymers. The glass transition temperatures of the polymers increased as trifluoromethyl mesogens increased, too. The N*–I phase transition temperatures show a negative deviate from ideal or linear behaviour. The values of the enthalpy changes for the cholesteryl containing polymers are rather low and this is attributed to the biaxiality of cholesteryl moiety which tends to reduce the change in the orientational order at the N*–I transition. Compared to the monomers, the polymers show wider mesophase region.     

β‐Diketiminatoytterbium aryloxides: synthesis,structural characterization,and catalytic activity for addition of amines to carbodiimides

The steric effect of an aryloxido group on the synthesis and molecular structures of ytterbium aryloxides supported by β‐diketiminato ligand L (L = [N(2,6‐Me₂C₆H₃)C(Me)]₂CH^?) is reported. Reactions of β‐diketiminatoytterbium dichloride, LYbCl₂(THF)₂, with NaOAr¹ in THF (Ar¹ = [2,6‐^tBu₂‐4‐MeC₆H₂], THF = tetrahydrofuran) at 60°C gave the corresponding ytterbium complexes LYb(OAr¹)Cl(THF) ( 1 ) and LYb(OAr¹)₂ (1), depending on the molar ratio of dichloride to sodium aryloxide, respectively, while the same reactions with NaOAr² and NaOAr³ (Ar² = [2,6‐ⁱPr₂C₆H₃], Ar³ = [2,6‐Me₂C₆H₃]) in 1:1 or 1:2 molar ratio in THF afforded only bisaryloxide complexes LYb(OAr²)₂(THF) (1) and LYb(OAr³)₂(THF) ( 4 ) in good yields, respectively. Complexes 1 , 2 , 3 , 4 were fully characterized, including X‐ray crystal structure analyses. All the complexes are efficient pre‐catalysts for the catalytic addition of amines to carbodiimides giving guanidines. Copyright © 2013 John Wiley & Sons, Ltd.     

Synthesis and characterization of novel elastomeric poly(D,L-lactide urethane) maleate composites for bone tissue engineering

Here, we report the synthesis and characterization of a novel 4-arm poly(lactic acid urethane)-maleate (4PLAUMA) elastomer and its composites with nano-hydroxyapatite (nHA) as potential weight-bearing composite. The 4PLAUMA/nHA ratios of the composites were 1:3, 2:5, 1:2 and 1:1. FTIR and NMR characterization showed urethane and maleate units integrated into the PLA matrix. Energy dispersion and Auger electron spectroscopy confirmed homogeneous distribution of nHA in the polymer matrix. Maximum moduli and strength of the composites of 4PLAUMA/nHA, respectively, are 1973.31 ± 298.53 MPa and 78.10 ± 3.82 MPa for compression, 3630.46 ± 528.32 MPa and 6.23 ± 1.44 MPa for tension, 1810.42 ± 86.10 MPa and 13.00 ± 0.72 for bending, and 282.46 ± 24.91 MPa and 5.20 ± 0.85 MPa for torsion. The maximum tensile strains of the polymer and composites are in the range of 5–93%, and their maximum torsional strains vary from 0.26 to 0.90. The composites exhibited very slow degradation rates in aqueous solution, from approximately 50% mass remaining for the pure polymer to 75% mass remaining for composites with high nHA contents, after a period of 8 weeks. Increase in ceramic content increased mechanical properties, but decreased maximum strain, degradation rate, and swelling of the composites. Human bone marrow stem cells and human endothelial cells adhered and proliferated on 4PLAUMA films and degradation products of the composites showed little-to-no toxicity. These results demonstrate that novel 4-arm poly(lactic acid urethane)-maleate (4PLAUMA) elastomer and its nHA composites may have potential applications in regenerative medicine.     

A three-dimensional in vitro culture model for primary neonatal rat ventricular myocytes

To overcome bad prognosis of patients with heart failure and the lack of organ donors, cardiac tissue engineering has developed as a biomimetic approach to repair, replace, and regenerate the damaged cardiac tissue. During the past decade years, researchers are devoted to find different natural and/or synthetic materials that can build appropriate physical structures to contain and organize implanted cells. In this study, we present a new method for primary neonatal rat cardiomyocytes culture in vitro using alginate/collagen/chitosan hydrogel. To investigate the feasibility of this material as scaffold for cardiac myocytes, neonatal rat ventricular myocytes were isolated and encapsulated in alginate-based beads cross-linked with calcium ion. The growth of cells was evaluated by staining with α-Sarcomeric actin (α-SCA) and Troponin T type 2 (TNNT2), and the viability of cardiomyocytes was studied in vitro by assessing the expression levels of several cardiac ion channels, including CACNL1A1, Connexin 43 and SCN5A. The results showed a significant increase in cardiac myocytes number, and the expression levels of CACNL1A1, Connexin 43 (Cx43) were up-regulated significantly except SCN5A, as compared with two-dimensional cultures. Moreover, extracellular matrix produced by the seeded cells themselves was observed by staining with fibronectin. Taken together, these findings indicate that this alginate/collagen/chitosan hydrogel bead is suitable for supporting the growth and retaining the morphologic and electrophysiologic characteristics of primary cultured rat cardiac muscle cells.     

Switchable peptide-equipped protein/cucurbit[7]uril supramolecular assembly for targeted drug delivery

ABSTRACT

Herein, we develop a switchable peptide-equipped protein/cucurbit[7]uril (CB[7]) supramolecular assembly as novel targeted drug vector. Specifically, bovine serum albumin (BSA) is used to interact with CB[7], serving as the core of drug vector. Then, a peptide shield layer is formed on the surface of BSA/CB[7], yielding peptide-equipped supramolecular assembly (Pep@BSA@CB[7]). The equipped peptide shield layer is composed of switchable peptide probes consisting of a polycationic cell-penetrating peptide (CPP) motif, a polyanionic motif and a linking motif, and therefore provides a variety of desirable properties. First, the CPP motif displays excellent cell penetration ability and can facilitate internalisation of the drug vector. Secondly, the polyanionic motif performs intramolecular electrostatic interaction with CPP motif and thereby can reduce non-targeted delivery towards normal cells. Thirdly, the linking motif can be specifically cleaved by matrix metalloproteinases 2 that is up-regulated in tumour microenvironment, thus enabling precise cancer-targeting. As a consequent, Pep@BSA@CB[7] can serve as a promising drug vector that exhibits superior targeting ability and high uptake efficiency towards cancer cells, which may be of great potential in cancer-targeted treatment.