石墨-六角氮化硼微晶混合物与水高压反应产物分析

 利用球磨法制备石墨-六角氮化硼微晶混合物，并在6.1 GPa、800~1 500 ℃条件下与水进行高压反应，以便研究用水作触媒合成B-C-N三元化合物的可能性。通过对反应产物的XRD、XPS谱分析发现：高压下随着温度的升高，反应产物中出现再结晶石墨，其晶化程度逐渐提高；但没有出现再结晶六角氮化硼，也未出现立方氮化硼。在球磨不充分条件下，石墨-六角氮化硼混合物的XRD谱没有完全弥散，它们与水高压反应时，能观察到石墨与立方氮化硼分别结晶的现象，但都没有形成B-C-N晶化结构。     

2‐Cyanoprop‐2‐yl dithiobenzoate mediated reversible addition–fragmentation chain transfer polymerization of acrylonitrile targeting a polymer with a higher molecular weight

The reversible addition–fragmentation chain transfer (RAFT) polymerization of acrylonitrile (AN) mediated by 2‐cyanoprop‐2‐yl dithiobenzoate was first applied to synthesize polyacrylonitrile (PAN) with a high molecular weight up to 32,800 and a polydispersity index as low as 1.29. The key to success was ascribed to the optimization of the experimental conditions to increase the fragmentation reaction efficiency of the intermediate radical. In accordance with the atom transfer radical polymerization of AN, ethylene carbonate was also a better solvent candidate for providing higher controlled/living RAFT polymerization behaviors than dimethylformamide and dimethyl sulfoxide. The various experimental parameters, including the temperature, the molar ratio of dithiobenzoate to the initiator, the molar ratio of the monomer to dithiobenzoate, the monomer concentration, and the addition of the comonomer, were varied to improve the control of the molecular weight and polydispersity index. The molecular weights of PANs were validated by gel permeation chromatography along with a universal calibration procedure and intrinsic viscosity measurements. ¹H NMR analysis confirmed the high chain‐end functionality of the resultant polymers. © 2007 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 45: 1272–1281, 2007     

Normal families and exceptional functions

In this paper, we obtain some normality criteria for families of meromorphic functions that concern the exceptional functions of derivatives.     

An algorithm for decomposing a polynomial system into normal ascending sets

We present an algorithm to decompose a polynomial system into a finite set of normal ascending sets such that the set of the zeros of the polynomial system is the union of the sets of the regular zeros of the normal ascending sets.If the polynomial system is zero dimensional,the set of the zeros of the polynomials is the union of the sets of the zeros of the normal ascending sets.     

对期望理论的两个重要推进——损失厌恶系数λ及参考点研究

行为金融学是近20年来最为重要的新兴金融理论,期望理论更是其中的亮点,其运用领域之广超乎人们的想象,所以对它的完善改进具有非常重要的意义。本文对期望理论中的损失厌恶系数和参考点问题进行了深入研究,并且得出了创新性的结果:损失厌恶系数不是常数而是动态变量;得出了内生且纳入更多投资者行为特征的参考点。这些结果是对期望理论的重要改善和推进,对其在大量金融领域和涉及到财富偏好的问题的解决中都大有裨益。     

解约束优化问题的QP-free可行域方法

本文利用一个新的分片线性NCP函数提出一个新的可行的QP-free方法解非线性不等式约束优化问题.不同于其他的QP-free方法,这个方法只考虑在工作集中的约束函数,工作集是积极集的一个估计,因此子问题的维数不是满秩的.这个方法可行的并且不需假定严格互补条件、聚点的孤立性得到算法的全局收敛性,并且积极约束函数的梯度不要求线性独立的,其中由拟牛顿法得到的子矩阵不需要求一致正定性.     

In situ observation of NaBi(WO4)2 dendrite growth and the study on microstructure of solidification

The dendrite growth process of transparent NaBi(WO₄)₂ with small prandtl and high melting point was studied by using the in-situ observation system. According to the dynamic images and detailed information, there are two kinds of restriction effect on the dendrite growth, the competition between arms and branches and the convection in the melt. The dendrite growth rate was time dependent, and the rate of arm growth reached the maximum 5.8 mm/s in the diffusive-advective region and rapidly decreased in the diffusive-convective region. The growth rate of branch had the same change trends as the arm’s. Based on the EPMA-EDS data of solidification structure of quenched NaBi(WO₄)₂ melt, it was found that there were component differences from stoichiometric concentration in the melt near the interface during the growth process. Supported by the National Natural Science Foundation of China (Grant No. 50331040) and the Innovation Funds from Shanghai Institute of Ceramics, Chinese Academy of Sciences (Grant No. SCX0623)     

影响产生均匀等离子体状态的几个因素

 用数值模拟方法研究利用辐射加热来产生均匀等离子体状态,它可被用来测量元素的辐射不透明度,校验辐射不透明度理论。研究了在辐射加热铁的“三明治”型靶时影响生成均匀等离子体状态的几个重要因素（样品厚度、CH膜厚度和辐射源）所起的作用，研究发现，当铁等离子体通过热传导达到均匀状态时，其尺度必须与此时的传热距离相当，从而定出铁样品的厚度；低Z介质CH膜对铁等离子体有明显的箍束作用，调整CH膜的厚度可以调节所产生的等离子体状态；调整不同方向上的CH膜厚度，可以控制铁等离子体的膨胀方向，使它尽可能地达到一维膨胀，使得反推出的等离子体密度可以更加准确；样品的种类、厚度以及外面的低Z介质厚度决定了在某时刻能获得的等离子体状态，以及为产生此等离子体状态所需的最低辐射能。     

反向驱动的异质结有机薄膜电致发光

成功制备了结构为ITO／PDDOPV／PPQ／Al的异质结聚合物发光二极管。该器件在正反向偏压下均可发光。在正向偏压下的光发射主要来自PDDOPV，但在反向偏压下的光发射则包括来自PPQ的蓝光发射和PDDOPV的黄光发射。蓝光强度与黄光强度的比值随着反向偏压的增加而增加，当反向直流电压分别为22V、24V、26V、28V时，其电致发光光谱中PPQ与PDDOPV的峰高比IPPQ／IPDDOPV分别为1．092、1．329、1．605、2．046。换句话说，该器件的发光颜色是压控可调的，这对实现彩色显示是极为有利的。分析了在反向偏压下的发光机理以及IPPQ／IPDDOPV受电压控制的原因。     

Characterization of ceramic PVD thin films on AZ31 magnesium alloys

Ceramic thin films have been widely used to protect the metal substrate as coatings in the past years. In order to improve the poor corrosion resistance of AZ31 magnesium alloy, the study in this paper used the electron beam evaporation method to prepare ceramic PVD films on its surface with TiO₂ and Al₂O₃ as donors, respectively. Atomic force microscopy (AFM), scanning electron microscope (SEM), energy dispersive X-ray spectrometer (EDS), Auger electron spectroscopy (AES) and X-ray diffraction (XRD) were used to investigate the surface morphology, composition and microstructure of the thin films. Both films deposited on AZ31 took on compact top surface morphologies and grew as amorphous structures on substrate. AES test not only showed that films compositions deviated the standard stoichiometric ratios, but also found that element Mg diffused into films and existed as magnesium oxide in the TiO_x film as well as the AlO_x film. In the electrochemical corrosion test, the AlO_x coating on AZ31 exhibited the largest electrochemical impedance in a 3.5% NaCl solution. But it did not show better corrosion resistance than others for the poorer adhesion. Even if its thickness was small, the TiO_x coating on AZ31 exhibited the best corrosion resistance in this study. According to the observation and analysis, the damage of these films on AZ31 in aggressive solutions was mainly due to the existence of pores, microcracks, vacancies and poor adhesion between coating and substrate.