Temperature effects on surface activity and application in oxidation of toluene derivatives of CTAB-SDS with KMnO4

The γ_cmc values of CTAB-SDS decrease from 63.67 mN/m at 10‡C to 36.38 mN/m at 90‡C, slightly lower than those of either CTAB or SDS. Correspondingly, the CMC of CTAB-SDS decreases almost by half. The increase of surface activity of CTAB-SDS can be attributed to the relatively weak electrostatic interaction at high temperature, which is supported by the increase of solubility of CTAB-SDS with rise in temperature. Catalytic effect on oxidation of toluene derivatives with potassium permanganate follows the order CTAB-SDS > SDS > CTAB. This is not caused by the dissociative effect of CTAB-SDS with low surface activity at low temperature, as seen from the fact that almost all oxidative products can be retrieved for different toluene derivatives and surfactants by mimicking the conditions of reaction. In the emulsifications of toluene derivatives at 90‡C, the time that turbid water layers of surfactant solutions take to become clear is the same as that of the catalytic effect on oxidation of toluene derivatives. Thus, it can be inferred that surfactants can improve the oxidation yields of toluene derivatives by increasing the contact between two reacting phases.     

扩宽OMA-Ⅵ同时谱宽的新方法

OMA－Ⅵ存在同时谱宽窄的缺点，本文用一种新方法大幅度地扩宽了它的同时谱宽，且不降低其系统分辨率，应用效果甚佳。     

Comparison of stimulated-emission-pumping fluorescence dip spectrometry and conventional fluorescence spectrometry in application to supersonic jet spectrometry

Summary A supersonic jet spectrum of 9,10-dichloroanthracene is measured by stimulated-emission-pumping fluorescence dip spectrometry and conventional fluorescence spectrometry. The performance obtained is compared for these spectrometric methods, providing same information concerned with the energy level of the ground state. The former is more preferential for measurement of a high-resolution spectrum, since the spectral resolution is determined by the linewidth of the dumping laser. On the other hand, the latter is more preferential for measurement with better sensitivity at the expense of the spectral resolution, since the fluorescence throughput can be improved by increasing the slit width of the monochromator.Dedicated to Professor Dr. Wilhelm Fresenius on the occasion of his 80th birthday     

Three-dimensional atom probe study of the segregation behaviour of Ni91Pt9 alloy after sputtering

To investigate local ordering and segregation phenomenon in a Ni91Pt9-alloy after sputtering and annealing a 3D optical atom probe (OAP) has been used. The specimen tips have been prepared from polycrystalline samples. To sputter the samples a separate preparation chamber with a scannable Ar-sputter-gun is connected to the OAP vessel. When necessary, the sample can be electrically heated to induce segregation and cure the altered layer. After a heat treatment of a Ni91 at. %Pt 9 at.% specimen at 1100 K the surface of a (111)-oriented specimen is enriched in platinum by a factor of two in relation to the bulk. The phenomenon of short-range ordering has been investigated on the surface and in the subsurface volume. A 3D reconstruction of this annealed NiPt specimen shows regions with high concentration of platinum that gives an indication at short-range ordering. Uniform sputtering of the tip without a heat treatment induces a decisive depletion of Pt on the surface and the following subatomic layers. The atom-probe results of specimens in thermal equilibrium are in close agreement to further surface sensitive results obtained from Ion Scattering Spectroscopy (ISS) and Auger Electron Spectroscopy (AES).     

A simple method improving the analyzing accuracy of circular groove guide

A simple method is introduced to improve the analysing accuracy of circular groove guide. With this method, the characteristic equation of circular groove guide is derived and its solution is given and discussed.The Project Supported by National Natural Science Foundation of P.R.China     

CONCEPTUAL DESIGN STUDIES OF AN 84 GHz, 500 kW, CW GYROTRON

The feasibility of an 84 GHz, 500 kW, CW gyrotron for ECRH on an experimental tokamak will be presented in this paper. Mode competition and mode selection procedures are carefully investigated by considering various candidate modes and the TE_10,4 mode is chosen as the operating mode. A conventional cylindrical cavity resonator with weak input and output tapers and parabolic roundings is considered for interaction studies. Self-consistent, both single mode and time-dependent, calculations are carried out and power and efficiencies are computed for a typical set of beam parameters. The results show that an output power of well over 500 kW, CW and efficiency around 40% can be reached without a depressed collector.     

激光等离子体2660紫外探针及干涉系统

成功地在六路高功率Nd玻璃激光装置上建立了2660紫外激光探针和适合紫外波段的Normaski干涉仪,首次将可见波长的连续激光应用于紫外干涉仪中靶成像调整和光路准直。利用该紫外光干涉仪,在铜柱状靶(φ500μm)上测量了厚等离子体中高达0.6n。的电子密度。     

Error analysis: a tool for selecting travel demand models

In developing travel demand models it is generally assumed that the base-year data used in developing the parameters, as well as the forecasted data to be used as independent variables for the design year, are of acceptable quality. The purpose of this paper is to present the application of error propagation theory in assesing the predictive quality of one type of travel demand forecasting model (multinomial logit models) and to demonstrate how error considerations can be used as a tool for identifying the optimal model. The general conclusions of this study are that: (1) it is indeed possible to quantify errors in dependent variables in logit models as a consequence of errors in independent variables; and (2) error consideration can be used as a tool for identifying the optimal model from a set of candidate models. Further research is recommended to develop better insights into the phenomenon of error propagation so that the consideration of errors can be a factor in decisions on model selection.