工作气压对磁控溅射ITO薄膜性能的影响

工作气压在ITO薄膜的制备过程中是一个重要的工艺参数,直接决定着薄膜的性能.本文利用射频磁控溅射方法,采用氧化铟锡陶瓷靶材,在衬底温度为175℃,工作气压范围为0.45～1.0 Pa条件下,制备了氧化铟锡透明导电薄膜.研究了工作气压对其微观结构、表面形貌和光电特性的影响.在衬底温度为175℃、纯氩气中制备的氧化铟锡薄膜电阻率为3.04 ×10-4 Ω·cm、可见光波段(400～800 nm)透过率为91.9;,适合用作异质结太阳电池的前电极和减反射膜.     

6H-SiC衬底片的表面处理

相比于蓝宝石,6H-SiC是制作GaN高功率器件更有前途的衬底.本文研究了表面处理如研磨、化学机械抛光对6H-SiC衬底表面特性的影响.用显微镜、原子力显微镜、拉曼光谱、卢瑟福背散射谱表征了衬底表面.结果表明经过两步化学机械抛光后提高了表面质量.经第二步化学机械抛光后的衬底具有优异的表面形貌、高透射率和极小的损伤层,其表面粗糙度RMS是0.12nm.在该衬底上用MOCVD方法长出了高质量的GaN外延膜.     

香花石形态所反映的一种可能的孪晶结构

香花石是我国发现的第一个新矿物,它的形态非常复杂.本文基于香花石形态上出现了左形与右形相聚的现象,对香花石形态进行了重新思考,认为同一单形的左形与右形不能相聚形成单晶体,只能形成孪晶,因此,对原香花石晶体图进行了一些修正,认为原香花石晶体图可能是一个孪晶图.这对深入认识晶体形态及晶体对称理论、澄清长期以来人们并没有足够重视的一些基本概念有重要意义.     

缓冲层ZnPc对有机电致发光器件特性的影响

本文研究了酞菁锌(ZnPc)薄膜的表面形貌及ZnPc薄膜作为缓冲层对有机电致发光器件(OLEDs)光电特性的影响.对比两组样品的AFM图像,ZnPc薄膜相比于ITO薄膜,其表面的岛面积较大,薄膜表面更连续平整,基本上覆盖了ITO膜表面针孔,减少了表面的缺陷.另外,ZnPc薄膜的岛分布均匀有序.使用ZnPc作为缓冲层的器件性能明显好于未使用ZnPc修饰的器件,在7.42V的驱动电压下的最大发光亮度达到1.428kcd/m2,在4.3V电压驱动下时,最大光功率效率为1.411m/W;而未使用缓冲层的器件在8V的驱动电压下达到最大发光亮度达到1.212kcd/m2,在5.5V电压驱动下时,最大光功率效率为0.931m/W.     

Decomposition Reaction of Zn-MPA（3-Mercaptopropionic Acid） Complex Under Microwave Irradiation

The thermal decomposition of Zn-MPA complex was investigated under microwave irradiation. ZnO and ZnS nanocrystals could be obtained by decomposing Zn-MPA（3-mercaptopropionic acid） complex under different reaction conditions. It was found that both the pH value of the solution and the molar ratio of Zn2＋ and MPA can play an important role in the formation of ZnO and ZnS nanocrystals. MPA mainly acts as an S source or as a complexing agent. This study provides a new route for the controllable preparation of semiconductor nanocrystals.     

Cloning, Expression and Purification of Wheat Acetyl-CoA Carboxylases CT Domain in E.coil

The entire gene of carboxyltransferase(CT) domain of acetyl-CoA carboxylase(ACCase) from Chinese Spring wheat(CSW) plastid was cloned firstly,and the 2.3 kb gene was inserted into PET28a+ vector and expressed in E.coil in a soluble state.The (His)6 fusion protein was identified by SDS-PAGE and Western blot.The recombinant protein was purified by affinity chromatography,and the calculated molecular mass(Mr) was 88000.The results of the sequence analysis indicate that the cloned gene(GeneBank accession No.EU124675) was a supplement and revision of the reported ACCase CT partial cDNA from Chinese Spring wheat plastid.The recombinant protein will be significant for us to investigate the recognizing mechanism between ACCase and herbicides,and further to screen new herbicides.     

A Novel Method for Pattern Recognition of GIS Partial Discharge via Multi-Information Ensemble Learning

Partial discharge (PD) is the main feature that effectively reflects the internal insulation defects of gas-insulated switchgear (GIS). It is of great significance to diagnose the types of insulation faults by recognizing PD to ensure the normal operation of GIS. However, the traditional diagnosis method based on single feature information analysis has a low recognition accuracy of PD, and there are great differences in the diagnosis effect of various insulation defects. To make the most of the rich insulation state information contained in PD, we propose a novel multi-information ensemble learning for PD pattern recognition. First, the ultra-high frequency and ultrasonic data of PD under four typical defects of GIS are obtained through experiment. Then the deep residual convolution neural network is used to automatically extract discriminative features. Finally, multi-information ensemble learning is used to classify PD types at the decision level, which can complement the shortcomings of the independent recognition of the two types of feature information and has higher accuracy and reliability. Experiments show that the accuracy of the proposed method can reach 97.500%, which greatly improves the diagnosis accuracy of various insulation defects.     

聚合物气体辅助注射成型制品的形态结构

作为一种由常规注射成型发展起来的聚合物加工技术,气体辅助注射成型具有节约原材料、缩短成型周期以及提高制品性能等优点,已得到广泛的应用.由于气辅成型过程是一个在刚、柔双重约束界面条件下进行的多相复杂体系的多次流动过程,因而其形态结构的形成、发展和演化要远比常规注塑成型复杂.然而在气辅成型的形态结构方面,国内外的研究一直以来开展得较少.近年来,作者在聚合物及其共混物、复合材料气辅成型制品的形态结构方面已开展了广泛的研究工作,本文对这些工作和一些重要结果作了总结,并简要分析了成型过程中剪切场对形态演化的影响,最后对该研究方向的发展趋势作了展望.     

HIGH-FREQUENCY VIBRATIONS OF CORRUGATED CYLINDRICAL PIEZOELECTRIC SHELLS

Coupled extensional and flexural cylindrical vibrations of a corrugated cylindrical piezoelectric shell consisting of multiple pieces of circular cylindrical surfaces smoothly connected along their generatrix are studied. To validate the results for the case of relatively thick shells or equivalently high-frequency modes with short wavelengths, existing analysis is extended by considering shear deformation and rotatory inertia. An analytical solution is obtained. Based on the solution, resonant frequencies and mode shapes are calculated.     

PVC/MBS/纳米 BaSO4 复合材料的制备及其性能

采用熔融共混法制备聚氯乙烯(PVC)/甲基丙烯酸甲酯-丁二烯-苯乙烯共聚物(MBS)/纳米重晶石(nano-BaSO4)三元复合材料,考察其力学性能和热稳定性能,并用扫描电镜观察冲击断面的形态.结果表明:MBS 与 nano-BaSO4 可协同增韧 PVC;当 MBS、nano-BaSO4 的含量分别为 10%、1%时,材料的韧性和刚性可同时得以改善,其冲击断面表现出典型的韧性断裂特征;热重分析显示添加 1%nano-BaSO4 可显著提高 PVC/MBS 的热稳定性能,其第一降解阶段的初始分解温度和最快分解温度分别提高了 10℃和14℃.