Temperature dependence of excitonic luminescence from nanocrystalline ZnO films

The properties of the excitonic luminescence for nanocrystalline ZnO thin films are investigated by using the dependence of excitonic photoluminescence (PL) spectra on temperature. The ZnO thin films are prepared by thermal oxidation of ZnS films prepared by low-pressure metalorganic chemical vapor deposition (LP-MOCVD) technique. The X-ray diffraction (XRD) indicates that ZnO thin films have a polycrystalline hexagonal wurtzite structure with a preferred (0 0 2) orientation. A strong ultraviolet (UV) emission peak at 3.26 eV is observed, while the deep-level emission band is barely observable at room temperature. The strength of the exciton-longitudinal-optical (LO) phonon coupling is deduced from the temperature dependence of the full-width at half-maximum (FWHM) of the fundamental excitonic peak, decrease in exciton-longitudinal-optical (LO) phonon coupling strength is due to the quantum confinement effect.     

LIDAR mapping of ozone-episode dynamics in Paris and intercomparison with spot analyzers Supplementary material available at http://link.springer.de/journals/apb

Continuous mapping of an ozone episode in Paris in June 1999 has been performed using a differential absorption lidar system. The 2D ozone concentration vertical maps recorded over 33 h at the Champ de Mars are compiled in a video clip that gives access to local photochemical dynamics with unprecedented precision. The lidar data are compared over the whole period with point monitors located at 0-, 50-, and 300-m altitudes on the Eiffel Tower. Very good agreement is found when spatial resolution, acquisition time, and required concentration accuracy are optimized. Sensitivity to these parameters for successful intercomparison in urban areas is discussed. Received: 11 February 2002 / Published online: 14 March 2002     

Thermal conductivity of poly(vinyl chloride)/polycaprolactone blends

Thermal diffusivity, heat capacity, and density of polyvinyl chloride/polycaprolactone (PVC/PCL) blends were measured by the laser flash method, DSC, and pycnometry, respectively. The thermal conductivity of the PVC/PCL blends was determined from the results. The miscibility of the blend and crystallinity of PCL were determined by DSC. The effect of blend structure on thermal conductivity is discussed. The phase compositions of the PVC/PCL blends are of three types depending on PCL content: i.e., up to 33%, from 33 to 70%, and above 70% PCL by weight. Thermal conductivity, thermal diffusivity, and heat capacity of the PVC/PCL blends are strongly affected by the phase composition of the blend, which changes in a complicated way with PCL content. © 1994 John Wiley & Sons, Inc.     

Matrix representation of three-dimensional astigmatic resonators

Three-dimensional astigmatic resonators, typical examples of which are the resonators bounded by cylindrical-spherical mirrors and cylindrical-cylindrical mirrors oriented at an arbitrary crossed angle, are investigated in detail by using a complex curvature tensor concept and generalized tensor ABCD law. Computerized numerical calculations illustrate some interesting characteristics of these astigmatic resonators.     

Efficacy of the accent method of voice therapy

The management of voice disorders may follow one of four approaches: surgical, pharmacological, technical aid, and/or voice therapy. The latter approach offers a wide variety of techniques, each based on certain theoretical beliefs. One of these techniques is the Smith Accent Method. The principles and goals of the Accent Method are presented. The results of its application are discussed. This technique proved effective for cases of functional voice disorders, vocal nodules, and some degrees of vocal fold paralysis.     

A novel detection scheme for vibration monitoring using optical techniques

An all-fibre interferometer which allows the measurement of the movement (speed and distance) of a vibrating body is presented. An electronic signal processing scheme is used and this is contrasted with the measurement of velocity through an optical processing technique, which is however, more complex and expensive to implement. The overall simplicity of the electronic technique, the low cost of components and the use of an all-fibre arrangement make this an attractive system to implement where the more limited information available is sufficient for monitoring purposes.     

Dynamic behavior classification of a model for a continuous bio-reactor subject to product inhibition

The dynamic behavior of the continuous biological reactor subject to product inhibition is analysed and classified in terms of multiplicity and stability of steady states and existence and stability character of limit cycles. Various boundary conditions are derived which delineate the parameter space into regions of dynamically different behavior. The predicted types of behavior are then illustrated by numerical computation of cells and product concentration trajectories.     

High-quality hydroxyapatite coating on biocompatible materials by laser-assisted laser ablation method

A new method for high-quality hydroxyapatite (HAp) coating is developed, the laser-assisted laser ablation method. In this method, two lasers are used. One is used for ablation of a HAp target. The other, the assist laser, is used to irradiate a Ti substrate surface. The effects of the assist laser irradiation are to anneal the HAp coating and to improve its adhesive strength to the Ti substrate. The quality of the HAp coating depends on the delay time of the assist-laser irradiation. HAp coatings obtained at a delay time of 10 microseconds or more are more amorphous. It was confirmed that the amorphous part of a coating dissolves in simulated body fluid, while the crystalline part does not. The value of the Ca/P ratio in a coating obtained at a delay time of a few microseconds is close to the stoichiometric value. PACS 81.16.Mk     

Morphology of Nylon-6 blends with styrenic polymers

The morphology of blends of styrenic polymers in a matrix of 75% Nylon-6 prepared in a Brabender Plasti-Corder was examined by scanning electron microscopy. Styrene/acrylonitrile copolymers (SAN) form smaller particles as the AN level increases owing to the corresponding decrease in the SAN–polyamide interfacial tension. Various styrenic polymers containing functional groups, maleic anhydride or oxazoline type, that can react with Nylon-6 during melt processing were added to the SAN phase which also led to a decrease in the particle size owing to the graft copolymer formed in situ. The effects of functional group type, amount of functional groups per chain, amount of functional polymer added, and the miscibility of the styrene/maleic anhydride (SMA) and SAN copolymers on the morphology of the styrenic phase in the Nylon-6 matrix are described. © 1992 John Wiley & Sons, Inc.