Surface and interfacial properties of PVDF/acrylic copolymer blends before and after UV exposure

Morphological and chemical properties of both the surface and interface of poly(vinylidene fluoride)/poly(methyl methacrylate)-co-poly(ethyl acrylate) (PVDF/PMMA-co-PEA) blend films have been investigated before and after the samples were exposed to ultraviolet (UV) irradiation using a xenon arc lamp at 50 °C and 9% relative humidity (RH) for 7 months. Surface and interfacial morphologies were studied by atomic force microscopy (AFM). Chemical composition information was obtained by confocal Raman microscopy, attenuated total reflection-FTIR spectroscopy (ATR-FTIR), X-ray photoelectron spectroscopy (XPS), and contact angle measurements. Results show an enrichment of the PVDF material at the air surface, while the acrylic copolymer enriches the interface. Blends having greater than 50% mass fraction of PVDF show little change in the surface morphology after UV exposure for 7 months. However, for a lower PVDF content, blends exhibit significant degradation of PMMA-co-PEA copolymer and a much rougher surface after UV exposure. Microstructural changes in the PVDF spherulites are also observed after UV degradation. It is found that the surface and interfacial morphologies are correlated with the chemical properties.     

X-ray photoelectron spectroscopy characterization of oxidated Si particles formed by pulsed ion-beam ablation

X-ray photoelectron spectroscopy (XPS) is used to probe oxidation states of Si species in particles deposited using a pulsed ion-beam evaporation method. The effects of He ambient gas, ion beam intensity and post-treatments on the oxides composition and oxygen content have been studied. It is found that presence of He ambient gas led to a profound oxidation of Si species as compared to that prepared in vacuum at the same ion-beam ablation energy, i.e. both increase of SiO₂ component and oxygen concentration in the oxides coverage. The deposition in He also resulted in an increase of oxygen concentration even under lower ablation intensity, but a higher Si suboxides concentration. It is revealed that the reaction between Si and O was controlled by the ion beam intensity (temperature of Si plasma) and the gas ambient (collision probability of Si and O species). The difference in structure of oxide layers for samples obtained under various conditions is discussed based on the results of XPS analyses.     

Schottky metal library for ZNO-based UV photodiode fabricated by the combinatorial ion beam-assisted deposition

A binary alloy Schottky barrier diode on zinc oxide (ZnO) was developed using the combinatorial ion beam-assisted deposition system. The compositional fraction of the binary alloy was continuously varied using the composition-spread technique, to control the Schottky barrier height. After metal deposition, patterned Schottky diodes were fabricated on a ZnO single-crystal substrate. Pt-Ru alloy was selected from the work function viewpoint. Our experiments showed that the compositional fraction of the Schottky binary alloys changed continuously as designed and the Schottky barrier heights measured by current-voltage (I-V) measurements increased with increasing Pt content. Maximum barrier height difference for ZnO was 137 meV. Using ion beam deposition in parallel with the combinatorial system showed that the Schottky barrier heights for ZnO can be controlled by binary metal alloying.     

Investigations of He implantation and subsequent annealing effects in InP

The influence of 70 keV He⁺ ion implantation and subsequent annealing of Cz-indium phosphide (InP) samples has been investigated using a slow positron beam-based Doppler broadening spectrometer. Three samples with ion fluences of 1 × 10¹⁶, 5 × 10¹⁶ and 1 × 10¹⁷ cm⁻² were studied in the as-implanted condition as well as after annealing at 640 °C for times between 5 and 40 min. It was found that the line-shape parameter of the positron-electron annihilation peak in the implanted layer increases after 5 min annealing, then after longer annealing times it starts to decline gradually until it reaches a value close to the value of the as-grown sample. This implies that vacancy-like defects can be created in InP by He implantation followed by short-thermal annealing at T > 600 °C. Comparison of the results with a study where cavities were observed in He-implanted InP has been carried out.     

Slow positron beam study of corrosion-related defects in pure iron

Corrosion-related defects of pure iron were investigated by measuring Doppler broadening energy spectra (DBES) of positron annihilation and positron annihilation lifetime (PAL). Defect profiles of the S-parameter from DBES as a function of positron incident energy up to 30 keV (i.e. ∼1 μm depth) were analyzed. The DBES data show that S-parameter increases as a function of positron incident energy (mean depth) after corrosion, and the increase in the S-parameter is larger near the surface than in the bulk due to corrosion. Furthermore, information on defect size from PAL data as a function of positron incident energy up to 10 keV (i.e. ∼0.2 μm depth) was analyzed. In the two-state trapping model, the lifetime τ₂ = 500 ps is ascribed to annihilation of positrons in voids with a size of the order of nanometer. τ₁, which decreases with depth from the surface to the bulk, is ascribed to the annihilation of positrons in dislocations and three-dimensional vacancy clusters. The corroded samples show a significant increase in τ₁ and the intensity I₂, and near the surface the corroded iron introduces both voids and large-size three-dimensional vacancy clusters. The size of vacancy clusters decreases with depth.     

Preliminary studies on a variable energy positron annihilation lifetime spectroscopy system

There are many advantages in being able to perform positron annihilation lifetime spectroscopy (PALS) using a variable energy positron beam, the most obvious being the easy identification of different defect types at different depths. The difficulty in conducting variable energy (VE) PALS studies lies in the fact that a “start” signal is required to signal the entry of the positron into the target. Two methods have been used to overcome this problem, namely the bunching technique, which employs radio frequency (RF) cavities and choppers, and secondly the use of secondary electrons emitted from the target. The latter technique is in terms of experimental complexity much simpler, but has in the past suffered from poor time resolution (typically ∼500 ps). In this work, we present a series of computer simulations of a design based on the secondary electron emission from thin C-foils in transmission mode which shows that significant improvements in time resolution can be made with resolutions ∼200 ps being in principle possible.     

Molecular dynamics simulation of processing using AFM pin tool

A three-dimensional molecular dynamics (MD) model is utilized to investigate the effect of tool geometry on the deformation process of the workpiece and the nature of deformation process at the atomic-scale. Results show that different states exist between the atomic force microscope (AFM) pin tool and the workpiece surface, i.e. the non-wear state, the ploughing state, the state in which ploughing is dominant and the state in which cutting plays a key role. A relationship between the deformation process of the workpiece and the potential energy variation is presented. The potential energy variation of atoms in different deformed regions in the workpiece such as plastically deformed region, elastically deformed region and the mixed deformation region is different. The features of variations of potential energy are discussed.     

Surface functionalisation of polymer nanofibres by sputter coating of titanium dioxide

The surface properties of nanofibres are of importance in various applications. In this work, electrospun polyamide nanofibres were used as substrates for creating functional nanostructures on the nanofibre surfaces. A RF magnetron sputter coating was used to deposit the functional layer of titanium dioxide (TiO₂) onto the nanofibres. Atomic force microscopy (AFM), X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS) and environmental scanning electron microscopy (ESEM) were employed to study the topography, grain structure and wetting of the nanofibre surfaces, respectively. The AFM results indicated a significant difference in the morphology of the nanofibres before and after the TiO₂ sputter coating. The XRD analysis showed the amorphous structures of the TiO₂ deposition layer. XPS spectra reflected the chemical features of the deposited nanostructures. The ESEM observation revealed that the surface wettability of TiO₂ sputter coated nanofibres was significantly improved after UV irradiation.     

Magnetic and electrical transport properties of delta-doped amorphous Ge:Mn magnetic semiconductors

We report on the growth and characterization of delta-doped amorphous Ge:Mn diluted magnetic semiconductor thin films on GaAs (0 0 1) substrates. The fabricated samples exhibit different magnetic behaviors, depending on the Mn doping concentration. The Curie temperature was found to be dependent on both the Mn doping concentration and spacing between the doping layers. A sharp drop in magnetization and rise in resistivity are observed at low temperature in samples with high Mn doping concentrations, which is also accompanied by a negative thermal remanent magnetization (TRM) in the higher temperature range. The temperature at which the magnetization starts to drop and the negative TRM appears show a correlation with the Mn doping concentration. The experimental results are discussed based on the formation of ferromagnetic regions at high temperature and antiferromagnetic coupling between these regions at low temperature.     

Fabrication of magnetic composite nanofibers of poly(ε-caprolactone) with FePt nanoparticles by coaxial electrospinning

In this article, composite nanofibers of poly(ε-caprolactone) (PCL) with iron–platinum (FePt) nanoparticles were successfully fabricated via coaxial electrospinning. The structure and morphology of FePt/PCL composite nanofibers were observed using transmission electron microscope and scanning electron microscope, respectively. The magnetic behavior of FePt/PCL composite nanofibers was investigated by alternating gradient magnetometer at room temperature.