变形镜部分驱动器断电失效对校正性能的影响

变形镜在长期工作的过程中,压电陶瓷驱动器因累积疲劳效应会导致其失效,从而导致校正性能的降低.从变形镜的影响函数出发,将失效驱动器的电压置零,采用有限元方法建立变形镜疲劳失效模型,重点分析畸变波前的形态分布、入射光束的类型和驱动器的排布方式等对校正能力的影响.实验结果表明,在部分驱动器失效的情况下,变形镜应当根据高斯型随...     

随机双指数记忆耗散系统的非马尔可夫扩散

针对具有双指数耗散记忆核函数的两自由度耦合系统, 本文利用Laplace变换导出了热宽带噪声激励下该系统响应二阶矩的解析表达式. 并观察到位移二阶矩不同于单自由度情形下的反常扩散:<x²(t)> ∝ t^α (0<α<2, α≠1), 而是随时间及噪声等参数变化呈现普遍的振荡扩散现象.分析可得, 阻尼耦合因子B使粒子远离简谐势场的束缚, <x²(t)>随B的增大扩散加剧而摩擦系数增大却使其趋于平稳状态.进一步, 若两热噪声互关联时, 较小的互关联时间对二阶矩的影响较大, 反之作用较小. 伴随互关联强度递增, 位移二阶矩的扩散加剧, 位移间的相关性加强, 与物理直观相符. 关键词： 热噪声 非马尔可夫扩散 广义朗之万方程 关联性     

不同磁场环境下Heisenberg XXZ自旋链中的热量子失协

本文研究了不同磁场环境下一维Heisenberg XXZ自旋链中两量子比特的热量子失协特性. 在四种不同的磁场环境下: 1) B₁=B₂=0 (无磁场); 2) B₁≠0, B₂=0 (磁场只作用于其中一个量子比特); 3) B₁=B₂ (均匀磁场); 4) B₁=-B₂ (非均匀磁场), 对分别作用在每个量子比特上的磁场B₁和B₂对其量子关联的影响作了详细的讨论, 且数值计算和比较了其量子失协和量子纠缠的异同. 结果显示: 在有限温度下, 量子失协相比于量子纠缠更普遍, 且非均匀磁场相比于均匀磁场对量子失协和量子纠缠更有用, 更有利于量子通讯和量子信息处理过程. 关键词： 量子关联 纠缠 量子失协     

铀的结构相变及力学性能的第一性原理计算

基于密度泛函理论, 分别计算了α, γ铀的晶格常数、平衡态体积、体弹模量及其导数等, 与实验和其他第一性原理计算结果符合较好; 并根据焓-压强曲线得到了两相的相变压强～111GPa. 通过体心立方结构理想拉伸强度的计算, 分析其在极端加载条件下的结构行为. 另外, 计算了小应变情况下U-Nb (6.25at.%) 的能量-应变关系, 发现对应于剪切模量c’的应变会使得该结构的能量降低, 揭示了该结构的力学不稳定性. 关键词： 铀 相变 理想强度 结构稳定性     

Scholte波与含泥沙两相流介质属性关系的分析及仿真验证

基于四种超声悬浮液模型Urick, Urick-Ament, HT, Mcclements分析了Scholte波在两相流体与多孔介质固体界面处的传播特性. 结合各模型的复波数表达式建立含泥沙流体-多孔介质固体界面波特征方程, 分析了Scholte波速与两相流体积含量、粒径等介质属性的关系. 通过仿真实验获得界面波信号, 运用时延估计获得Scholte波速与泥沙含量、粒径的关系, 发现所得的波速与Urick-Ament和HT理论有相对好的一致性. 关键词： Scholte波 两相流体 多孔介质 泥沙含量     

单载流子传输的双异质结光敏晶体管探测器的研究

基于器件仿真器Atlas, 建立了InP/InGaAsP单向载流子传输的双异质结光敏晶体管(UTC-DHPT)的二维模型, 分析讨论了器件性能与外延结构参数的关系. 设计出同时具有高响应度(≥17.93 A/W)和高特征频率(≥121.68 GHz)的UTC-DHPT, 缓解了传统的异质结光敏晶体管光电探测器中探测效率和工作速度的矛盾. 关键词： 单向载流子 光敏晶体管 电流放大倍数 响应度     

High resolution dynamic cardiac MRI using partial separability of spatiotemporal signals with a novel sampling scheme

The partial separability (PS) of spatiotemporal signals has been exploited to accelerate dynamic cardiac MRI by sampling two datasets (training and imaging datasets) without breath-holding or ECG triggering. According to the theory of partially separable functions, the wider the range of spatial frequency components covered by the training dataset, the more accurate the temporal constraint imposed by the PS model. Therefore, it is necessary to develop a new sampling scheme for the PS model in order to cover a wider range of spatial frequency components. In this paper, we propose the use of radial sampling trajectories for collecting the training dataset and Cartesian sampling trajectories for collecting the imaging dataset. In vivo high resolution cardiac MRI experiments demonstrate that the proposed data sampling scheme can significantly improve the image quality. The image quality using the PS model with the proposed sampling scheme is comparable to that of a commercial method using retrospective cardiac gating and breath-holding. The success of this study demonstrates great potential for high-quality, high resolution dynamic cardiac MRI without ECG gating or breath-holding through use of the PS model and the novel data sampling scheme.     

TiO2 Nanotube Array/Monolayer Graphene Film Schottky Junction Ultraviolet Light Photodetectors

Schottky junctions made from a titanium dioxide nanotube (TiO₂NT) array in contact with a monolayer graphene (MLG) film are fabricated and utilized for UV light detection. The TiO₂NT array is synthesized by the anodization and the MLG through a simple chemical vapor deposition process. Photoconductive analysis shows that the fabricated Schottky junction photodetector (PD) is sensitive to UV light illumination with good stability and reproducibility. The corresponding responsivity (R), photoconductive gain (G), and detectivity (D*) are calculated to be 15 A W^?1, 51, and 1.5 × 10¹² cm Hz^1/2 W^?1, respectively. It is observed that the fabricated PD exhibits spectral sensitivity and a simple power‐law dependence on light intensity. Moreover, the height of the Schottky junction diode is derived to be 0.59 V by using a low temperature I–V measurement. Finally, the working mechanism of the TiO₂NT array/MLG film Schottky junction PD is elucidated.     

Effect of Injection Parameters and Addition of Nanoscale Materials on the Shrinkage of Polypropylene Copolymer

The effect of variation of injection conditions and addition of nano-calcium carbonate (CaCO₃), nano-silicon dioxide (SiO₂) and full-vulcanized nano-powdered styrene butadiene rubber (PSBR) on the shrinkage of injection-molded polypropylene-ethylene copolymer (90/10, co-PP) were investigated. The results showed that the shrinkage was different for different locations along the flow path. The shrinkage in the length direction of the injection-molded sample varied with the adjustment of the processing parameters, while the shrinkage in the width and thickness direction was almost unchanged. The addition of nano-CaCO₃ and PSBR decreased the shrinkage of co-PP, while the shrinkage of co-PP/ SiO₂ composite was almost unchanged.     

Essential Work of Fracture Parameters of Injection-Molded Polypropylene/Polyolefin Elastomer Blends

The influence of polyolefin elastomer (POE) content on the fracture behavior of injection-molded polypropylene (PP)/POE blends was evaluated by means of the essential work of fracture (EWF) method. The results indicated that the EWF approach worked well for the PP/POE blends when POE content was 0～7.5 wt% of the blends. The specific essential work of fracture (w _e) increased with increasing POE content, and the dominant factor that affected w _e was the necking and subsequent fracture process. The specific nonessential work of fracture (βw _p) slightly decreased with increasing POE content, while the specific plastic work (w _p) showed an increasing trend with the decrease of the shape factor (β) of the specimen. Finally, it was shown that w _e could be predicted reasonably well via the COD values.