Crystalline titanium dichloride—an active catalyst in ethylene polymerization. II. Polymer structure,polymerization variables,and scope

Polymerization of ethylene with ball-milled titanium dichloride leads to a completely linear polymer with terminal unsaturation corresponding to approximately one carbon–carbon double bond per molecule. Polymerization rate is first-order in both monomer and catalyst concentration at 140°C. Due to a thermal deactivation of the catalyst, the polymerization rate falls sharply with temperature above 180°C. Propylene and butene-1 will copolymerization with ethylene in this system, propylene more efficiently than butene-1. Evidence for copolymerization of trans-2-butene, but not of the cis-isomer or of isobutene, in trace concentrations is presented. Propylene is homopolymerized to a product low in isotactic content. The significance of the structural and (limited) kinetic data in terms of the mechanism of polymerization are discussed.     

Instrumental neutron activation analysis of large samples: A pilot experiment

A large sample INAA (LS-INAA) was conducted based on available experimental conditions. Four different materials, e.g., a quartz-sand and three wastes from an incineration plant were analyzed on sample size of 1 kg. The neutron flux spatial distribution was determined by irradiation of flux monitors in the sample. The gamma-ray apparent counting efficiency was evaluated based on the effective-solid angle concept, using linear attenuation coefficients calculated from an iteration process. The k ₀- and the modified monostandard methods were modified for the LS-INAA. To check the LS-INAA performance, a conventional small sample INAA was carried out for the quartz sand and a waste. All detected elements in the LS-INAA are presented and the discussion is conducted to explore the sources of errors in the LS-INAA. As a pilot experiment, the information from this work will be used in constructing irradiation and counting devices for the new FRM-II neutron source in Garching, Germany.     

Direct injection of plasma to determine pseudoephedrine by high performance liquid chromatography with column switching

An HPLC method has been developed for the determination of pseudoephedrine in plasma using column switching. Preparation of the sample was simple in that only 1000 microL of water was added to 200 microL of plasma before injection. A 900 microL aliquot was injected onto the precolumn. Double distilled water was used to elute and remove proteins and polar components in the sample. The components retained on the precolumn were flushed forward onto the analytical column by the mobile phase (acetonitrile-0.2 mol/L ammonium sulphate, 10:90 v/v) with automated column switching. The limit of determination of pseudoephedrine in plasma was 12 ng/mL. The relative standard deviations of intra- and inter-assay for the determination of pseudoephedrine in plasma were 1.2-9.8% over the concentration range 1020-21.8 ng/mL. The mean recovery by on-line solid phase extraction was 94.76% (RSD = 1.1%).     

Differential determination of arsenic (III) and total arsenic with L-cysteine as prereductant using a flow injection non-dispersive atomic absorption device

Speciation of arsenic in environmental samples gains increasingly importance, as the toxic effects of arsenic are related to its oxidation state. A method was developed for the determination of trace amounts of arsenic (III) and total arsenic by flow injection hydride generation coupled with an in-house made non-dispersive AAS device. The total arsenic is determined after prereduction of arsenic (V) to arsenic (III) with L-cysteine in a low concentration of hydrochloric, acetic or nitric acid. The conditions for the prereduction, hydride generation and atomization were systematically investigated. A quartz tube temperature of 800 degrees C was found to be optimum in view of peak shape and baseline stability. Pb(II), Ni(II), Fe(III), Cu(II), Ag(I), Al(III), Ga(II), Se(IV), Bi(III) were checked for interfering with the 2 microg/L As(V) signal. A serious signal depression was only observed for Se(IV) and Bi(III) at a 150-fold excess. With the above system, arsenic was determined at a sampling frequency of about 1/min with a detection limit (3sigma) of 0.01 microg/L using a 0.5 mL sample. The reagent blank was 0.001+/-0.0003 absorbance units and the standard deviation of 10 measurements of the 2 microg/l As signal was found to be 1.2%. Results obtained for standard reference materials and water samples are in good agreement with the certified values and those obtained by ICP-MS     

An immune algorithm for resolution of multicomponent overlapping chromatograms

A novel immune algorithm for resolution and quantitative determination of the components in overlapping chromatograms was proposed by imitating biological immune systems. The algorithm takes an overlapping chromatogram as its input and subtracts the chromatograms of standard samples from the input by iteration of a network. When the residual does not change, the network will converge and chromatographic information of the components in overlapping chromatogram will be obtained. Both simulated and experimental data sets were investigated by the method. Results showed that both resolved results and recoveries of quantitative determination are satisfactory. Comparing with conventional least-square method, the immune algorithm is fast in calculation.     

Zur Ermittlung der Äthylen-Sequenzlängenverteilung und der chemischen Uneinheitlichkeit in Copolymeren mit Propylen durch Pyrolyse-Gas-Chromatographie

Pyrolysis coupled with gas chromatography has been applied to investigate the sequence distribution in copolymers of ethylene and propylene. The copolymers analyzed have been prepared with soluble Ziegler-Natta-catalysts and show different degrees of crystallinity. In one series of samples the methyl group of the propylene units has been labeled with tritium. It was then possible to detect carbons by flame ionization detector and simultaneously the methyl groups by the radio-detector in parallel. Within the errors of these methods the results from both detectors are consistent with the calculations from kinetics. The accuracy of the data is best in copolymers with long ethylene sequences. By GPC fractionation a heterogeneity in the chemical composition can be observed. One component of the copolymers is of high molecular weight, while the other has a molecular weight of less than 1000 and is very rich in ethylene. The influence of chemical heterogeneity on sequence distribution derived from kinetics and pyrolysis has been discussed. A mechanism in which chains with different chemical composition are growing from different species of the catalyst has been proposed. The experimental results show that the heterogeneity is not critical for the sequence analysis by kinetics and pyrolysis.     

Simultaneous determination of neodymium, erbium and holmium in rare earth mixtures with 2-phenyltrifluoroacetone and octylphenol poly(ethyleneglycol) ether by third-derivative spectrophotometry

The complexes of the rare earth metals with 2-phenyltrifluoroacetone in the presence of TX-100 are reported. The characteristic absorbances of neodymium, holmium and erbium complexes can be increased by factors of 8.5, 31 and 15 respectively, compared to those of the cholrides. The third-derivative spectra have been used to eliminate the interference of cerium, and the sensitivities are increased again by factors of 7.4, 5.5 and 6.5. A method for the direct determination of neodymium, erbium and holmium in rare earth mixtures is proposed.     

Color Displays with Gel-Glass Dispersed Liquid Crystals

Liquid crystal microdroplets trapped into silica gel-glasses by sol-gel processes may be used for display applications. Gel-glass dispersed liquid crystals (GDLC) are switched between opaque and transparent states by applying external AC-voltage signals; no polarizers are required. The feasibility of applying these materials to colored displays has been explored. A comparative study of different dyes for GDLC color displays, which were either embedded in the sol-gel matrix or dissolved in the liquid crystal microdroplets is presented.     

Adsorption configuration and local ordering of silicotungstate anions on Ag(100) electrode surfaces

X-ray reflectivity, cyclic voltammetry, and scanning tunneling microscopy (STM) are used to examine the structure of alpha-SiW12O4(4-) or silicotungstic acid (STA) adsorbed on Ag(100) in acid solution. The voltammetry shows that STA passivates the Ag surface relative to electron transfer to a solution redox species. STM images reveal the formation of a series of lattice structures, one of which can be associated with a commensurate ( radical13x radical13)R33.69 degrees structural model. X-ray reflectivity measurements show uniquely that STA orients with its four-fold axis perpendicular to the Ag(100) surface and that the center of the STA molecule is 4.90 A above the top layer of the Ag substrate. Analysis of bond lengths leads to a footprint of STA on Ag(100), in which the four terminal O atoms are located near the hollow sites and have a Ag-O bond length of 2.06 A. This bond length is consistent with a strong covalent interaction between STA and the Ag surface.     

Synthesis and Characterization of Ag2S Nanocrystals in Hyperbranched Polyurethane at Room Temperature

Ag₂S nanoparticles in hyperbranched polyurethane matrix were prepared through the in situ reaction with thioacetamide as the sulfur source at room temperature. Transmission electron microscopic analysis revealed a uniform spherical shape for Ag₂S nanoparticles, with an average size of about 4-10 nm and a narrow size distribution. X-ray powder diffraction and UV-vis spectroscopy were also used to characterize the obtained nanoparticles