Degradation of ZnS:Cu,Al,Au phosphor powder in different gas mixtures

The ZnS:Cu,Al,Au (P22G) phosphor powder was bombarded by an electron beam in an O₂ ambient, Ar ambient and other mixture of gases. These gases consisted of mixtures of O₂ and CO_x, and O₂, CO_x and Ar gas. Auger electron spectroscopy (AES) was used to monitor changes in the surface composition of the P22G phosphor during electron bombardment. When the P22G phosphor powder was exposed to the electron beam in a water-rich O₂ ambient, a chemically limited ZnO layer was formed on the surface. The electron beam degradation of the P22G phosphor powder was also performed in a dry O₂ ambient and a layer of ZnSO₄ was formed on the surface. The ZnSO₄ formation decayed exponentially with time and it is postulated that this was due to the diffusion of the charge reactants through the ZnSO₄ film to the reaction interfaces. The P22G phosphor exposed to the electron beam in an Ar ambient and to the other gas mixtures degraded at a lower rate than in the case of the O₂ ambient. This suggests that Ar and CO_x may suppress the degradation of the P22G phosphor powder.     

Viscoelastic properties of nanostructured natural rubber/polystyrene interpenetrating polymer networks

The effects of the blend ratio and initiating system on the viscoelastic properties of nanostructured natural rubber/polystyrene‐based interpenetrating polymer networks (IPNs) were investigated in the temperature range of ?80 to 150 °C. The studies were carried out at different frequencies (100, 50, 10, 1, and 0.1 Hz), and their effects on the damping and storage and loss moduli were analyzed. In all cases, tan δ and the storage and loss moduli showed two distinct transitions corresponding to natural rubber and polystyrene phases, which indicated that the system was not miscible on the molecular level. However, a slight inward shift was observed in the IPNs, with respect to the glass‐transition temperatures (T_g's) of the virgin polymers, showing a certain degree of miscibility or intermixing between the two phases. When the frequency increased from 0.1 to 100 Hz, the T_g values showed a positive shift in all cases. In a comparison of the three initiating systems (dicumyl peroxide, benzoyl peroxide, and azobisisobutyronitrile), the dicumyl peroxide system showed the highest modulus. The morphology of the IPNs was analyzed with transmission electron microscopy. The micrographs indicated that the system was nanostructured. An attempt was made to relate the viscoelastic behavior to the morphology of the IPNs. Various models, such as the series, parallel, Halpin–Tsai, Kerner, Coran, Takayanagi, and Davies models, were used to model the viscoelastic data. The area under the linear loss modulus curve was larger than that obtained by group contribution analysis; this showed that the damping was influenced by the phase morphology, dual‐phase continuity, and crosslinking of the phases. Finally, the homogeneity of the system was further evaluated with Cole–Cole analysis. © 2003 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 41: 1680–1696, 2003     

Microwave‐improved polymerization of ϵ‐caprolactone initiated by carboxylic acids

The ring‐opening polymerization of ε‐caprolactone (ε‐CL), initiated by carboxylic acids such as benzoic acid and chlorinated acetic acids under microwave irradiation, was investigated; with this method, no metal catalyst was necessary. The product was characterized as poly(ε‐caprolactone) (PCL) by ¹H NMR spectroscopy, Fourier transform infrared spectroscopy, ultraviolet spectroscopy, and gel permeation chromatography. The polymerization was significantly improved under microwave irradiation. The weight‐average molecular weight (M_w) of PCL reached 44,800 g/mol, with a polydispersity index [weight‐average molecular weight/number‐average molecular weight (M_w/M_n)] of 1.6, when a mixture of ε‐CL and benzoic acid (25/1 molar ratio) was irradiated at 680 W for 240 min, whereas PCL with M_w = 12,100 and M_w/M_n = 4.2 was obtained from the same mixture by a conventional heating method at 210 °C for 240 min. A degradation of the resultant PCL was observed during microwave polymerization with chlorinated acetic acids as initiators, and this induced a decrease in M_w of PCL. However, the degradation was hindered by benzoic acid at low concentrations. © 2002 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 41: 13–21, 2003     

Synthesis and characterization of isotopically enriched methylmercury (CH3201Hg+)

A simple procedure for the synthesis of an important standard, isotopically enriched methylmercury, which is not commercially available, has been established successfully. The isotopically enriched standard synthesized is utilized in conventional isotope dilution mass spectrometry (IDMS), as well as in speciated IDMS (SIDMS), for determination of the true concentration of methylmercury in environmental samples. The CH₃²⁰¹Hg⁺ standard has been synthesized from commercially available ²⁰¹HgO and tetramethyltin. The synthesis time required is 1 h at 60°C. The product is highly pure, yielding more than 90% as ²⁰¹Hg in CH₃²⁰¹Hg⁺. Hazardous dimethylmercury does not occur during this synthesis procedure. The product synthesized was analyzed using high‐performance liquid chromatography coupled with inductively coupled plasma mass spectrometry (ICP‐MS) and ICP‐MS alone in order to determine its concentration, isotopic composition and purity. The stability of the product was also evaluated for over 6 months and found to be stable at 4°C in the dark. The isotopically enriched methylmercury synthesized can be used in SIDMS and IDMS analyses as a standard. Copyright © 2003 John Wiley & Sons, Ltd.     

Lower bounds for sums of Barban-Davenport-Halberstam type (supplement)

This article was processed by the author using the IATEX style filecljourl from Springer-Verlag.     

Crystallographic report: Bis(norfloxacin)dilead(II) tetranitrate, [Pb2(H‐Norf)2(ONO2)4]

The centrosymmetric binuclear structure of [Pb₂(H‐Norf)₂(ONO₂)₄]shows the geometry around each lead(II) atom to be distorted trigonal bipyramidal with Pb–O distances ranging from 2.357(3) to 2.769(4) Å. Copyright © 2003 John Wiley & Sons, Ltd.     

Numerical study of simultaneous natural convection heat transfer from both surfaces of a uniformly heated thin plate with arbitrary inclination

 Numerical studies were conducted to investigate the natural convection heat transfer around a uniformly heated thin plate with arbitrary inclination in an infinite space. The numerical approach was based on the finite volume technique with a nonstaggered grid arrangement. For handling the pressure–velocity coupling the SIMPLE-algorithm was used. QUICK scheme and first order upwind scheme were employed for discretization of the momentum and energy convective terms respectively. Plate width and heating rate were used to vary the modified Rayleigh number over the range of 4.8×10⁶ to 1.87×10⁸. Local and average heat transfer characteristics were compared with regarding to the inclination angle. The empirical expressions for local and average Nusselt number were correlated. It has been found that for inclination angle less than 10^∘, the flow and heat transfer characteristics are complicated and the average Nusselt number can not be correlated by one equation while for inclination angle larger than 10^∘, the average Nusselt number can be correlated into an elegant correlation. Received on 18 April 2001 / Published online: 29 November 2001     

On path lengths modulo three

We show that between any two nodes of a cubic, planar, three-connected graph there are three paths whose lengths are 0, 1, and 2 modulo 3, respectively. The proof is by a rather extensive case analysis. Counterexamples show that all three hypotheses (i.e., planarity, degree-three, and three-connectivity) are necessary.