Buckling of a stiff thin film on a compliant substrate in large deformation

A finite-deformation theory is developed to study the mechanics of thin buckled films on compliant substrates. Perturbation analysis is performed for this highly nonlinear system to obtain the analytical solution. The results agree well with experiments and finite element analysis in wavelength and amplitude. In particular, it is found that the wavelength depends on the strain. Based on the accurate wavelength and amplitude, the membrane and peak strains in thin films, and stretchability and compressibility of the system are also obtained analytically.     

Multi-layer thin films/substrate system subjected to non-uniform misfit strains

Current methodologies used for the inference of thin film stress through curvature measurement are strictly restricted to stress and curvature states that are assumed to remain uniform over the entire film/substrate system. These methodologies have recently been extended to a single layer of thin film deposited on a substrate subjected to the non-uniform misfit strain in the thin film. Such methodologies are further extended to multi-layer thin films deposited on a substrate in the present study. Each thin film may have its own non-uniform misfit strain. We derive relations between the stresses in each thin film and the change of system curvatures due to the deposition of each thin film. The interface shear stresses between the adjacent films and between the thin film and the substrate are also obtained from the system curvatures. This provides the basis for the experimental determination of thin film stresses in multi-layer thin films on a substrate.     

从像上提取非旋转对称系统的传递函数制作解卷空间滤波器

本文提出从高分辨电子显微像中,利用光学、全息和部分相干等方法,提取传递函数,制作相位和振幅滤波器,实现解卷,提高高分辨电子显微像的分辨率.     

A novel methodology for the synthesis of 1-desoxy-Δ-tetrahydrocannabinol (THC) analogues

A versatile and efficient sequence was developed for the synthesis of 1-desoxy-Δ⁸-THC analogues and is demonstrated by the synthesis of sulfonamide analogues with an acetylene group at the C-2^′ position in the side chain. In this procedure the 1-desoxy-Δ⁸- THC ring structure is built first and the synthesis of the side chain is then developed.     

Assessment of two‐equation turbulence modelling for high Reynolds number hydrofoil flows

This paper presents an evaluation of the capability of turbulence models available in the commercial CFD code FLUENT 6.0 for their application to hydrofoil turbulent boundary layer separation flow at high Reynolds numbers. Four widely applied two‐equation RANS turbulence models were assessed through comparison with experimental data at Reynolds numbers of 8.284×106 and 1.657×107. They were the standard k–εmodel, the realizable k–εmodel, the standard k–ωmodel and the shear‐stress‐transport (SST) k–ωmodel. It has found that the realizable k–εturbulence model used with enhanced wall functions and near‐wall modelling techniques, consistently provides superior performance in predicting the flow characteristics around the hydrofoil. Copyright © 2004 John Wiley & Sons, Ltd.     

Experimental investigation and theoretical modeling of liquid entrainment in a horizontal tee with a vertical-up branch

This article describes a comprehensive literature review of liquid entrainment in horizontal pipes with vertical-up branches. Deficiencies in the available data and correlations were identified. The Air–water Test Loop for Advanced Thermal–hydraulic Studies (ATLATS) was constructed and entrainment onset and steady-state data were collected for a wide range of flow conditions. Using new insights gained from experimental testing, the authors developed a model for predicting the onset of entrainment and steady-state entrainment rate. Previously published correlations, along with the new model, are compared against all available data. The new model shows very good agreement with the onset data, but is not very good at predicting branch quality at high liquid flow rates.     

The glow curve structure for the LiF:Mg,Cu,Na,Si TL detector with dopants concentrations and sintering temperatures

The glow curve structures for LiF:Mg,Cu,Na,Si TL detectors with various dopant concentrations and sintering temperatures were investigated for the improvement of the glow curve structure and sensitivity of the TL detector. The dopant concentrations were varied over the following ranges: Mg (0–0.25 mol%), Cu (0–0.07 mol%), Na and Si (0–1.5 mol%). With increasing Cu concentration, the intensity of the main peak was intensified and reached a maximum at a concentration of 0.05 mol%. The high-temperature peak was reduced. The dependency of the main peak intensity on the Mg concentration exhibits a sharp maximum at 0.2 mol%. The intensity of the high-temperature peak tends to rise slightly with increasing Mg concentration. It was found that the optimum concentrations of the dopants in the LiF:Mg,Cu,Na,Si TL material are Mg: 0.2 mol%, Cu: 0.05 mol%, Na and Si: 0.9 mol%. The dependency of the main peak intensity on sintering temperature exhibits a very sharp maximum at 830°C. The high-temperature peak was rapidly reduced after 825°C.     

Plasmon-induced terahertz absorption and photoconductivity in a grid-gated double-quantum-well structure

The terahertz absorption spectra of plasmon modes in a grid-gated double-quantum-well field-effect transistor structure is analyzed theoretically and numerically using the scattering matrix approach and is shown to faithfully reproduce strong resonant features of recent experimental observations of terahertz photo-conductivity in such a structure.     

Atom transfer radical polymerization of methyl methacrylate by copper(I)‐pyridine‐2‐carboximidate catalysts

Pyridine‐2‐carboximidates [methyl ( 1a ), ethyl ( 1b ), isopropyl ( 1c ), cyclopentyl ( 1d ), cyclohexyl ( 1e ), n‐octyl ( 1f ), and benzyl ( 1g )] were prepared from the reaction of 2‐cyanopyridine with the corresponding alcohols. Cyclopentyl‐substituted 1d was found to be a highly effective ligand for copper‐catalyzed atom transfer radical polymerization (ATRP) of methyl methacrylate (MMA). For example, the observed rate constant for a CuBr/ 1d catalytic system was found to be nearly twice as high as the cyclohexyl‐substituted CuBr/ 1e catalytic system [k_obs = (1.19 vs 0.56) × 10^?4 s^?1). The effects of the solvents, temperature, catalyst/initiator, and solvent/monomer ratio on the ATRP of MMA were studied systematically for the CuBr/ 1d catalytic system. The optimum condition for the ATRP of MMA was found to be a 1:2:1:400 [CuBr]_o/[ 1d ]_o/[ethyl 2‐bromoisobutyrate]_o/[MMA]_o ratio at 60 °C in veratrole solution, which yielded well‐defined poly(MMA) with a narrow molecular weight distribution of 1.14. The catalytically active copper complex 2d was isolated from the reaction of CuBr with 1d . Narrow molecular weight distributions as low as 1.06 were achieved for the CuBr/ 1d catalytic system by employing 10% of the deactivator CuBr₂. © 2004 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 2747–2755, 2004