Validation and application of an LC-MS/MS method for the simultaneous quantification of 13 pharmaceuticals in seawater

Knowledge of the presence of micropollutants such as pharmaceuticals, in coastal areas, is very limited; therefore, the main objective of this study was to optimize and validate a new analytical method for the quantitative analysis of 13 multiclass pharmaceuticals in seawater. Target compounds included antibiotics, non-steroidal anti-inflammatory drugs, β-blockers, lipid regulators and one psychiatric drug. A combination of solid-phase extraction and liquid chromatography coupled with multiple mass spectrometry enabled their detection at the low nanogram per litre level. The limits of quantification varied between 1 and 50 ng L^-1, for most components the linearities were more than 0.99 and the recoveries obtained in seawater (95–108%) were satisfactory. This method was applied to seawater and estuarine water samples collected in the Belgian coastal zone, to assess the prevalence of common pharmaceuticals in this marine environment. Seven pharmaceuticals, including compounds of which the presence in marine environments had not been reported earlier, were detected, with salicylic acid and carbamazepine being the most abundant, in concentrations up to 855 ng L^-1.     

Sunbed radiation provokes cutaneous vitamin D synthesis in humans--a randomized controlled trial

We wanted to investigate whether the use of sunbeds with sunlamps emitting mainly UVA and only 0.5% or 1.4% UVB will increase the level of serum 25-hydroxyvitamin D (25(OH)D). In a randomized, controlled, open study on healthy, Caucasian females (> 50 years) sunbed radiation was given as follows: four 6-min sunbed sessions (days 0, 2, 4 and 7) and four 12-min sunbed sessions (days 9, 11, 14 and 16 ) with sunlamps emitting 0.5% UVB (n = 20) or with sunlamps emitting 1.4% UVB (n = 15). The controls (n = 21) had no intervention. Serum levels of 25(OH)D were measured on days 0, 9 and 18 in all three groups. The average increase in serum 25(OH)D from day 0 to day 9 was 12 nmol L(-1) (SD 11 nmol L(-1), P = 0.0002) in the 0.5% UVB group and 27 nmol L(-1) (SD 9 nmol L(-1), P < 0.0001) in the 1.4% UVB group. From day 9 to day 18 a further but not significant increase in serum 25(OH)D of 3 nmol L(-1) (SD 9 nmol L(-1), P = 0.2) in the 0.5% UVB group and 0.6 nmol L(-1) (SD 18 nmol L(-1), P = 0.9) in the 1.4% UVB group was seen. No significant changes were found in the control group. Increasing with UVB dose and exposure time, 37-64% of the sunbed sessions resulted in side effects such as erythema or polymorphic light eruption. The results showed that sunbeds emitting 0.5% and 1.4% UVB increased 25(OH)D serum levels. The increases were dose dependent but reached a plateau after few sessions. Sunbed use as vitamin D source is, however, not generally recommendable due to the well-known carcinogenicity and high frequency of acute side effects.     

PLLA Coating of Active Implants for Dual Drug Release

Cochlear implants, like other active implants, rely on precise and effective electrical stimulation of the target tissue but become encapsulated by different amounts of fibrous tissue. The current study aimed at the development of a dual drug release from a PLLA coating and from the bulk material to address short-term and long-lasting release of anti-inflammatory drugs. Inner-ear cytocompatibility of drugs was studied in vitro. A PLLA coating (containing diclofenac) of medical-grade silicone (containing 5% dexamethasone) was developed and release profiles were determined. The influence of different coating thicknesses (2.5, 5 and 10 µm) and loadings (10% and 20% diclofenac) on impedances of electrical contacts were measured with and without pulsatile electrical stimulation. Diclofenac can be applied to the inner ear at concentrations of or below 4 × 10⁻⁵ mol/L. Release of dexamethasone from the silicone is diminished by surface coating but not blocked. Addition of 20% diclofenac enhances the dexamethasone release again. All PLLA coatings serve as insulator. This can be overcome by using removable masking on the contacts during the coating process. Dual drug release with different kinetics can be realized by adding drug-loaded coatings to drug-loaded silicone arrays without compromising electrical stimulation.     

Computation of the Coupled Dynamics of Fibers in a Spray

The PUR-fiber-spray molding technology is a manufacturing process which produces polyurethane-based (PUR) composites by spraying the matrix together with reinforcing fibers in a tool form or on a substrate. Thereby chopped fibers are laterally (sidewise) injected in the polyurethane-air spray cone for wetting before the entire composite is spread on the substrate, where it starts curing. To investigate and compute the fiber orientation and density distribution in the final composites manufactured by this process, a new approach simplifying the multiply coupled interaction of the three phases is presented in this paper. Hereby it is presumed that the final position and orientation of a fiber on a substrate results from its dynamics and coupled interactions with air, PUR-droplets and other fibers within the spray cone. Thus, a model of the process is built, that computes the transient behavior of the air-liquid droplets mixture by the CFD code ANSYS Fluent and its influence on the dynamics of the fibers by an extra code called FIDYST. For this multiphase problem two approaches are presented for the droplet-fiber coupling using a concept called “homogenization” of the liquid phase (droplets in the continuous phase). (© 2010 Wiley-VCH Verlag GmbH & Co. KGaA, Weinheim)     

Experimental Evidence for the Existence of Neutral P(6): A New Allotrope of Phosphorus

High-energy collisions of Cp*P(6)(+) cations yield neutral P(6) molecules (see reaction), thus providing the first experimental evidence for the existence of this new allotrope of phosphorus.     

Determination of (13)C natural abundance of amino acid enantiomers in soil: methodological considerations and first results

The application of a combined gas chromatography-combustion/isotope ratio mass spectrometry (GC-C/IRMS) method for stable carbon isotope analysis of amino acid enantiomers in soil samples is presented. Triplicate delta(13)C analyses of pentafluoropropionyl (PFP) isopropyl ester derivatives of 27 amino acid enantiomers revealed that discrimination of (13)C during derivatization is different for different amino acid enantiomers and different amounts. Injection of increasing amounts of amino acid derivatives showed that the isotopic signal varied up to 10 per thousand for D-aspartic acid. Correction for the delta(13)C signal of underivatized amino acid enantiomers is possible for all investigated amino acid enantiomers using logarithmic functions. Operating the GC-C/IRMS system in the split-mode (split ratio 1:12) is possible but resulted in a higher isotopic discrimination. The detection limit approached 3 ng for some amino acid enantiomers in the splitless mode, while the lower limit of routine determination exceeded 10 ng injection amount. The upper limit at which accurate stable isotope values were obtained was 200 ng injection amount. Compound-specific delta(13)C analysis of alanine, valine, aspartic and glutamic acid showed that the D-forms were enriched in (13)C relative to the L-forms, suggesting that microbes significantly contributed to the formation of the D-enantiomers in soil.