Novel silver‐tubing method for quantitative introduction of water into high‐temperature conversion systems for stable hydrogen and oxygen isotopic measurements

A new method to seal water in silver tubes for use in a TC/EA (thermal conversion/elemental analyzer) reduction unit using a semi‐automated sealing apparatus can yield reproducibilities (1 standard deviation) of δ²H and δ¹⁸O measurements of 1.0‰ and 0.06‰, respectively. These silver tubes containing reference waters may be preferred for the calibration of H‐ and O‐bearing materials analyzed with a TC/EA reduction unit. The new sealing apparatus employs a computer‐controlled stepping motor to produce silver tubes identical in length. The reproducibility of the mass of water sealed in tubes (in a range of 200–400 µg) can be as good as 1%. Approximately 99% of the sealed silver tubes are satisfactory (leak free). Although silver tubes sealed with reference waters are robust and can be shaken or heated to 110°C with no loss of integrity, they should not be frozen because the expansion during the phase transition of water to ice will break the cold seals and all the water will be lost. The tubes should be shipped in insulated containers. This new method eliminates air inclusions and isotopic fractionation of water associated with the loading of water into capsules using a syringe. The method is also more than an order of magnitude faster than preparing water samples in ordinary Ag capsules. Nevertheless, some laboratories may prefer loading water into silver capsules because expensive equipment is not needed, but users of this method are cautioned to apply the necessary corrections for evaporation, back exchange with laboratory atmospheric moisture, and blanks. Copyright © 2010 John Wiley & Sons, Ltd.     

Improved laser-induced forward transfer of organic semiconductor thin films by reducing the environmental pressure and controlling the substrate–substrate gap width

Laser-induced forward transfer (LIFT) has been investigated for bilayer transfer material systems: silver/organic film (Alq₃ or PFO). The LIFT process uses an intermediate dynamic release layer of a triazene polymer. This study focuses on the effect of introducing a controlled donor–receiver substrate gap distance and the effect of doing the transfer at reduced air pressures, whilst varying the fluence up to ∼200 mJ/cm². The gap between ‘in-contact’ substrates has been measured to be a minimum of 2–3 μm. A linear variation in the gap width from ‘in contact’ to 40 μm has been achieved by adding a spacer at one side of the substrate–substrate sandwich. At atmospheric pressure, very little transfer is achieved for Alq₃, although PFO shows some signs of successful doughnut transfer (with a large hole in the middle) in a narrow fluence range, at gaps greater than 20 μm. For the transfer of Ag/PFO bilayers at atmospheric pressure, the addition of a PFO layer onto the receiver substrate improved the transfer enormously at smaller gaps and higher fluences. However, the best transfer results were obtained at reduced pressures where a 100% transfer success rate is obtained within a certain fluence window. The quality of the pixel morphology at less than 100 mbar is much higher than at atmospheric pressure, particularly when the gap width is less than 20 μm. These results show the promise of LIFT for industrial deposition processes where a gap between the substrates will improve the throughput.     

Evaluation of aerosol lead measurement techniques using laboratory generated super-micrometer particles

High levels of lead in some occupational environments still exist. These include lead paint abatement sites, smelting operations, small arms firing ranges, and other construction scenarios. New emerging technologies provide the capability to provide an on-site alternative to conventional laboratory methods for airborne lead. In this paper we describe the evaluation of two such technologies using laboratory prepared lead-laden super-micron aerosol particles. Size measurements by TSI Aerodynamic Particle Sizer™ indicated the fluctuation of the peak particle sizes varying less than 1% among different runs for a given solution concentration. The content of lead embedded in the particles varied from 14 to 18% between runs of three different lead solution concentrations. A commercially available instrument for airborne lead measurement, AeroLead™, showed promise of becoming fully validated with the addition of design enhancements, although not fully validated by the end of the research program. Some of these areas being reworked by the manufacturer include working electrode issues, such as a more uniform surface area. Once these have been addressed, the manufacturer plans to complete the field and laboratory validation procedures. In a subsequent study, the ABF-LIPS results shown in this paper indicated that the technology could be used to quantify lead in aerosol form with a signal-to-noise ratio of three or larger of approximately 100 μg m⁻³ or higher quantity in a few minutes of measurement interval. The estimated detection limit for Pb using the ABF-LIPS prototype was approximately 60 μg m⁻³. In comparison the Resource Conservation and Recovery Act (RCRA) limit for Pb emission is 250 μg m⁻³.     

Growth of Betti numbers

We discuss growth rates of Betti numbers in a family of coverings of a compact cell complex X, when the corresponding L² Betti number of X is zero. We show that the Betti numbers are bounded by a function, sub-linear in the order of the covering. If the appropriate Novikov-Shubin invariant of X is positive, the rate bounds are improved. For well behaved families (such as congruence covers of symmetric spaces), if the L² spectrum of X? has a gap at zero then the growth rate is bounded by the order of the covering raised to a power less than one.     

Estimating a Resource Selection Function With Line Transect Sampling

A resource selection probability function is a function that gives the probability that a resource unit (e.g., a plot of land) that is described by a set of habitat variables X1 to Xp will be used by an animal or group of animals in a certain period of time. The estimation of a resource selection function is usually based on the comparison of a sample of resource units used by an animal with a sample of the resource units that were available for use, with both samples being assumed to be effectively randomly selected from the relevant populations. In this paper the possibility of using a modified sampling scheme is examined, with the used units obtained by line transect sampling. A logistic regression type of model is proposed, with estimation by conditional maximum likelihood. A simulation study indicates that the proposed method should be useful in practice.     

Laser Machined Plastic Laminates: Towards Portable Diagnostic Devices for Use in Low Resource Environments

Despite significant progress in development of bioanalytical devices cost, complexity, access to reagents and lack of infrastructure have prevented use of these technologies in resource‐limited regions. To provide a sustainable tool in the global effort to combat infectious diseases the diagnostic device must be low cost, simple to operate and read, robust, and have sensitivity and specificity comparable to laboratory analysis. In this mini‐review we describe recent work using laser machined plastic laminates to produce diagnostic devices that are capable of a wide variety of bioanalytical measurements and show great promise towards future use in low‐resource environments.     

Functionalization of closo‐Borates via Iodonium Zwitterions

A simple method for the functionalization of closo‐borates [closo‐B₁₀H₁₀]^2? ( 1 ), [closo‐1‐CB₉H₁₀]^? ( 2 ), [closo‐B₁₂H₁₂]^2? ( 3 ), [closo‐1‐CB₁₁H₁₂]^? ( 4 ), and [3,3′‐Co(1,2‐C₂B₉H₁₁)₂]^? ( 5 ) is described. Treatment of the anions and their derivatives with ArI(OAc)₂ gave aryliodonium zwitterions, which were sufficiently stable for chromatographic purification. The reactions of these zwitterions with nucleophiles provided facile access to pyridinium, sulfonium, thiol, carbonitrile, acetoxy, and amino derivatives. The synthetic results are augmented by mechanistic considerations.