Wide mass range trapping using a 7-T internal source matrix-assisted laser desorption/ionization Fourier transform mass spectrometer

A wide mass range trapping experiment using internal source matrix-assisted laser desorption–Fourier transform mass spectrometry (MALDI–FTMS) was evaluated. In this method, the front trap plate potential is ramped up and the rear trap plate potential is simultaneously decreased using a cubic cell to trap ions over a wide range of mass-to-charge ratios. To apply this to MS/MS experiments, a second ion ejection procedure would remove unwanted ions, with the selected remaining ions then fragmented by collision-induced dissociation. In measurements using a 7.2-T unshielded magnet presented here, an approximately equimolar mixture of a set of poly(ethylene glycol) (PEG) species for the ramped measurements had peak areas of 1.0:1.0:1.0:1.0, as did the previously described integral method which gave peak areas of 1.0:1.1:1.0:1.0, in good agreement with the known composition of the samples deposited on the MALDI probe tip. Comparative MALDI–TOF in reflectron mode results were of similar quality for the equimolar mixture, giving a ratio of 1.0:1.0:1.2:0.9. All methods failed to varying degrees when individual PEG compositions of the trial mixture were changed. However, the previously described integral method showed relatively better results for all but the PEG 8000 doubled mixture.     

Laser desorption/ionization fourier transform mass spectrometry of thin films deposited on silicon by plasma polymerization of acetylene

Thin films deposited on silicon substrate by three different methods of plasma polymerization of acetylene were analyzed by direct laser desorption/ionization Fourier transform mass spectrometry. High-resolution mass spectra showed the presence of carbon clusters and hydrocarbon oligomers in different relative abundances. During unipolar and continuous discharge polymerization of acetylene-hydrogen gas mixtures, quadrupole mass spectra of the plasma constituents showed the presence of molecular species with m/z lower than 100 — mainly peaks of C₄H₂ and C₆H₂. Films produced had smooth surfaces and the corresponding LDI-FTMS spectra displayed only carbon cluster signals in the positive ion mode and both hydrocarbon and carbon cluster signals (with much higher relative abundance of carbon cluster signals) in the negative ion mode. Alternatively, during bipolar discharge with either higher acetylene gas flux (>40 cm³/min) or longer deposition times (>10 min), quadrupole mass spectra of the plasma constituents showed signals corresponding to polycyclic aromatic hydrocarbons (PAH) with m/z higher than 100. SEM pictures of the bipolar thin films demonstrated the presence of “flower” structures and nanoparticles developed on the surface. LDI-FTMS spectra of such thin films showed either total absence or lower relative abundance of carbon cluster signals, compared with hydrocarbon signals.     

Identification of volatile (micro) biological compounds from household waste and building materials by thermal desorption–capillary gas chromatography–mass spectroscopy

Volatile compounds from biodegradable household waste and infected building materials have been studied by dynamic or equilibrium headspace sampling and concentration on Tenax TA followed by thermal desorption and HRGC-MS. Equilibrium headspace sampling was also used to study vegetables stored for 14–18 days at ambient temperature. Over 200 compounds were tentatively identified. The concentration of organic sulfur compounds from garden waste was high enough to contribute to respiratory problems of waste handling personnel. Nitriles, alkyl nitro compounds, and alkyl nitrates were isolated from radish and carrot samples at low concentrations (10–50 ppb). Air monitoring in waste handling working environments may be required to ensure the safety of personnel. Branched aliphatic aldehydes, carboxylic acids, esters, and 2-alkanones were found in the headspace of the infected building materials, indicating that volatile compounds may be useful for detection of microbial growth in buildings.     

Fluorinated polyimide nanocomposites for CO2/CH4 separation

The purpose of this project was to synthesize fluorinated polyimide (PI) nanocomposite membranes in order to study the gas permeation rates and selectivity of carbon dioxide and methane. PIs were synthesized from 2,2‐bis(3,4‐anhydrodicarboxyphenyl)hexafluoropropane (6F dianhydride, 6FDA) and 4,4′‐diaminodiphenyl ether (oxydianiline, ODA) into which were incorporated nanoparticulate additives as follows: in situ TiO_2, both plain and treated with dodecyl sulfate surfactant, and organo‐clay (Cloisite®‐10 Å) at loads of 1, 3, and 5 wt% to the polyamic acid. Polyamic acid films were solvent cast, cured at 200°C then post‐cured at 300°C and measured for permeation data and for thermal properties. Glass transition temperatures ranged from 124 to 140°C for the cured PIs and from 142 to 147°C for the post‐cured materials, the nano‐inclusions having little discernable effect on this property. Thermogravimetric analysis (TGA) data show that the inclusion of Cloisite® or TiO₂ caused a small decrease of thermal stability from 555°C to about 532 to 541°C. The inclusion of clay causes a decreased permeation rate while the addition of TiO₂ improves the rate and selectivity. Treating the nanofillers with surfactant decreases selectivity and marginally increases rate of permeation of CO₂. Post‐curing caused a darkening of the composites, but not the neat PI. This heat treatment also resulted in a significantly decreased permeation rate, but a significantly increased selectivity. The resulting material shows superior gas separation properties to the commercially available PI, Matrimid® produced by Ciba‐Geigy. Copyright © 2008 John Wiley & Sons, Ltd.     

Abrasively immobilised multiwalled carbon nanotube agglomerates: a novel electrode material approach for the analytical sensing of pH.

We demonstrate for the first time that agglomerates of multiwalled carbon nanotubes (MWCNTs) can be formed in which the binder in the agglomerate is itself a redox-active molecular solid. Two separate agglomerates were formed by dissolving 9,10-phenanthraquinone (PAQ) or 1,2-napthaquinone (NQ) in acetone together with MWCNTs and adding an excess of aqueous solution to cause precipitation of agglomerates, approximately 10 microns in dimension, which consist of bundles of nanotubes running into and throughout the amorphous molecular solid that binds the agglomerate together. The nature of this structure, when immobilised on a substrate electrode and in contact with aqueous electrolyte solutions, gives rise to many three-phase boundaries, electrolyte|agglomerate|conductor, which is advantageous to the solid-state analytical electrochemistry of such a material as it imparts a larger electroactive surface area than other modified carbon electrodes. The two agglomerates each gave a voltammetrically measurable response to changes in pH; when abrasively immobilised on a basal plane pyrolitic graphite electrode a plot of peak potential against pH produced a linear response for both MWCNT-PAQ and MWCNT-NQ agglomerates over the pH range pH 1-12 and over the temperature range 20-70 degrees C.     

Quantitative comparison of preparation methodologies for x-ray fluorescence microscopy of brain tissue

X-ray fluorescence microscopy (XFM) facilitates high-sensitivity quantitative imaging of trace metals at high spatial resolution over large sample areas and can be applied to a diverse range of biological samples. Accurate determination of elemental content from recorded spectra requires proper calibration of the XFM instrument under the relevant operating conditions. Here, we describe the manufacture, characterization, and utilization of multi-element thin-film reference foils for use in calibration of XFM measurements of biological and other specimens. We have used these internal standards to assess the two-dimensional distribution of trace metals in a thin tissue section of a rat hippocampus. The data used in this study was acquired at the XFM beamline of the Australian Synchrotron using a new 384-element array detector (Maia) and at beamline 2-ID-E at the Advanced Photon Source. Post-processing of samples by different fixation techniques was investigated, with the conclusion that differences in solvent type and sample handling can significantly alter elemental content. The present study highlights the quantitative capability, high statistical power, and versatility of the XFM technique for mapping trace metals in biological samples, e.g., brain tissue samples in order to help understand neurological processes, especially when implemented in conjunction with a high-performance detector such as Maia.     

Evaluation of a Semi-Automated Multidimensional Gas Chromatography-Infrared-Mass Spectrometry System for Irritant Analysis

The use of a semi-automated, multidimensional gas chromatography (MDGC) Fourier transform infrared (FT-IR) mass spectrometry (MS) system in the determination of components causing contact dermatitis has been investigated. Fragrances are widely used in cosmetic and household products and are the leading cause of contact dermatitis. Such products contain numerous components such as emulsifiers, thickeners, solubilizers, pigments, antioxidants, and many other compounds, which can make it difficult to isolate the compound of interest. MDGC has the capability for component analysis in such complex matrices. A semi-automated MDGC system, which consists of a commercial instrument modified in our laboratory to include two computer controlled valves and a single trap which is manually controlled was evaluated for analysis of irritants in a total of thirteen soaps. Using heartcutting techniques, components causing dermatitis were identified in eight of the thirteen soaps by examining both the infrared and mass spectra obtained and matching them with computer spectral libraries. Results from these analyses show that a baby soap and three other mild soaps were free of irritants. Irritants were identified in the remaining eight soaps. In addition, to demonstrate the versatility of the semi-automated system, the enantiomeric composition of a chiral irritant in two soaps also was determined.     

N-acylsulfonamide linker activation by Pd-catalyzed allylation

N-Acylsulfonamide safety-catch linkers are versatile tools in solid-phase organic synthesis because of their stability. This stability necessitates linker activation prior to compound cleavage. Here, we demonstrate that the N-acylsulfonamide group can react with a pi-allyl palladium complex and that these mild and neutral conditions can be exploited for linker activation. The advantages of this process are illustrated by its use in the efficient synthesis of thioesters. We anticipate that this activation method will extend the utility of the N-acylsulfonamide group. [reaction: see text]