343 nm飞秒激光制备微孔阵列以增强聚氨酯合成革透湿性

为了提高聚氨酯(PU)合成革透湿性,分别使用343 nm飞秒激光和作为对比的1030 nm飞秒激光及1064 nm纳秒激光制备微孔阵列。采用扫描电镜(SEM)和3D激光扫描显微镜对比研究了微孔形貌。结果表明,343 nm飞秒激光可以制备出效果最佳的微孔。此外,分析了3种激光与PU涂层的作用机理,揭示了343 nm飞秒激光合成革微钻孔过程仅表现为光化学烧蚀,光化学和光热烧蚀同时发生于1030 nm飞秒激光钻孔过程,而1064 nm纳秒激光只显示了光热烧蚀。激光合成革表面钻孔后,测量其透湿性和抗张力。结果显示: 微孔密度越大,皮革透湿性(WVP)越大而抗张力越低,脉冲重叠的增加会导致WVP的增加和抗张力的下降;同时,随着脉冲重叠从91.7%降到50%,微孔直径从45 μm降低到30 μm,而微孔锥度从0.7°增加到12.1°;当脉冲重叠率为91.7%,微孔密度为2550/cm²时,最大的WVP增长率为306%。     

Broad band beam splitter based on the double-groove fused silica grating

In this paper, we propose a broad band 1 × 3 beam splitter operating in the telecommunication wavelength band under normal incidence, this device consisting of a double-groove fused silica grating layer is designed with using the inverse mathematical method and rigorous vector diffraction theory. It is shown from our calculations that the device presents excellent beam splitter ability for TE polarization light with the average diffraction efficiencies is more than 95% over ∼100 nm wavelength range, moreover, the uniformity of our beam splitter is better than 2% in the whole wavelength band. Furthermore, the physical understanding of the diffraction behaviors taking place inside the beam splitter gratings can be explained by the modal method.     

Improved l1-SPIRiT using 3D walsh transform-based sparsity basis

l1-SPIRiT is a fast magnetic resonance imaging (MRI) method which combines parallel imaging (PI) with compressed sensing (CS) by performing a joint l1-norm and l2-norm optimization procedure. The original l1-SPIRiT method uses two-dimensional (2D) Wavelet transform to exploit the intra-coil data redundancies and a joint sparsity model to exploit the inter-coil data redundancies. In this work, we propose to stack all the coil images into a three-dimensional (3D) matrix, and then a novel 3D Walsh transform-based sparsity basis is applied to simultaneously reduce the intra-coil and inter-coil data redundancies. Both the 2D Wavelet transform-based and the proposed 3D Walsh transform-based sparsity bases were investigated in the l1-SPIRiT method. The experimental results show that the proposed 3D Walsh transform-based l1-SPIRiT method outperformed the original l1-SPIRiT in terms of image quality and computational efficiency.     

All-angle broadband negative refraction of metal waveguide arrays in the visible range: theoretical analysis and numerical demonstration

In this Letter, we introduce a simple metal waveguide array for realizing all-angle wide frequency bandwidth negative refraction from the visible to infrared frequencies. Theoretical analysis from the rigorous coupled-wave theory reveals that the negative coupling constant resulting from the anomalous coupling of guided surface plasmon polariton modes contributes to the negative refraction. The analytical results are confirmed by finite-difference time-domain numerical simulations. Our result provides an alternative way to construct robust all-angle negative refractive materials operating in a wide range of frequency from the near-infrared to the visible range.     

GPS/LEO掩星正则变换反演方法

利用无线电全息方法, 如正则变换方法或全谱反演方法, 可以有效地解决大气多路径条件下GPS掩星信号的反演问题. 本文采用正则变换方法反演掩星资料, 模拟仿真反演结果显示正则变换方法可以准确地反演包含大气多路径效应的信号. 在模拟信号的相位中加入不同程度的高斯相位噪声后, 正则变换方法的反演结果会受到不同程度的影响. 用正则变换方法对2007年第71天至73天共约4500个COSMIC数据进行处理. 将其折射率反演结果和atmPrf资料 (利用全谱反演方法计算得到) 一起, 与对应的ECMWF 分析场资料进行统计比较, 结果表明: 在5 km以下, 正则变换方法计算的折射率的相对误差的平均值普遍大于atmPrf资料. 其原因可能为: 正则变换方法将信号从LEO轨迹后传播至辅助屏, 造成孔径缩小, 精度下降. 同时也讨论了信号截断对低对流层中反演精度和掩星个数的影响. 关键词： 无线电掩星 大气多路径 多相位屏技术 正则变换方法     

W波段回旋行波管输入输出段的改进设计

在回旋行波放大器的设计中,输入输出段的性能直接影响到整管输出功率、效率及增益。设计了一种采用渐变过渡段的输入耦合器来减少电子注在前端的截获,而且略微地提高了耦合特性,有效带宽达到4.06 GHz。采用二级切比雪夫渐变波导作为输出结构的耦合输出段,从仿真结果得到,在整个工作频段内,该结构中TE01工作模式的反射低于-20 dB,TE01模向杂模TE02和TE03的耦合分别在-20 dB和-30 dB以下。     

空间雷电探测实时采集定位系统

星载雷电探测定位系统是利用光学探测器探测闪电事件的地理位置和光脉冲波形,系统采用CPLD+DSP的数字图像处理方案,利用了CPLD复杂逻辑可编程特性将系统的部分或全部功能集成在一片CPLD上,减小了系统硬件复杂程度,节省了印制版空间.利用DSP高速数字信号处理特性完成实时处理图像数据的功能.系统用CPLD完成图像信号的采集、编码和存储控制,缩小了星载设备体积,简化了电路结构;用DSP完成大量图像数据处理工作,提高了系统工作的实时性.     

Study on scattering correction in fast neutron tomography at NECTAR facility

Fast neutron tomography has been established as an inspection and detection tool at the NECTAR facility at the FRM-II reactor.Scattered neutrons from the object become a major disturbance and bring in artifacts and deviations in reconstruction results,especially for hydrogenous material object.In this article,an iterative scattering correction method for fast neutron tomography was proposed.In each loop of iteration the scattering component of the projections will be simulated by Monte-Carlo program MCNPX based on the previous reconstruction result and then it will be subtracted from original projections.The differences between scattering components at different perspectives were quantitatively evaluated and an average scattering component image was used for all projections finally.Smooth and uniform slices with more clear edges were obtained and the new reconstructed attenuation coefficients are quite close to the real one compared to the results without scattering correction,in which case the relative error of the reconstructed attenuation coefficients is about 10%–30%.