Nano-tribological study on a super-hydrophobic film formed on rough aluminium substrates

A novel super-hydrophobic stearic acid (STA) film with a water contact angle of 166^o was prepared by chemical adsorption on aluminum wafer coated with polyethyleneimine (PEI) film. The micro-tribological behavior of the super-hydrophobic STA monolayer was compared with that of the polished and PEI-coated Al surfaces. The effect of relative humidity on the adhesion and friction was investigated as well. It was found that the STA monolayer showed decreased friction, while the adhesive force was greatly decreased by increasing the surface roughness of the Al wafer to reduce the contact area between the atomic force microscope (AFM) tip and the sample surface to be tested. Thus the friction and adhesion of the Al wafer was effectively decreased by generating the STA monolayer, which indicated that it could be feasible and rational to prepare a surface with good adhesion resistance and lubricity by properly controlling the surface morphology and the chemical composition. Both the adhesion and friction decreased as the relative humidity was lowered from 65% to 10%, though the decrease extent became insignificant for the STA monolayer. The project supported by the National Natural Science Foundation of China (50375151, 50323007, 10225209) and the Chinese Academy of Sciences (KJCX-SW-L2)     

Photorefractive Four-Wave Mixing Switches Utilizing Pockels Effect -Longitudinal and Lateral Switches-

We carried out detailed calculations for photorefractive wave-mixing switches based on one of three crystals with high electro-optic coefficients, namely, BaTiO₃, Strontium Barium Niobate (SBN (0.75)), and Potasium Sodium Strontium Barium Niobate (KNSBN). A comparison of results for the three crystals shows that a 0_-cut BaTiO³ crystal is suitable for a longitudinal switch and requires a voltage of about 80 for a 2-mm-thick crystal to induce sufficient phase mismatch. The electrodes must be transparent for the incident and diffracted beams. A 45_-cut SBN (0.75) crystal, however, is suitable for a lateral switch and requires a voltage of about 150 for a 1-mm-wide crystal. The electrodes do not need to be transparent.     

Errata: “Universality in Orthogonal and Symplectic Invariant Matrix Models with Quartic Potential”

The errata concern mainly the last computations for the universality of the local statistics of eigenvalues at the edge of the spectrum in parts (iii) of Theorems 2.3 and 2.4.     

Color Zone Map in Peripheral Vision at Various Illuminance Levels

We measured the entire region of mesopic and photopic vision to determine the color zone covering the visual field with unique red, yellow, green, and blue hue components. Eight kinds of test stimuli in the natural color system (NCS) color notation system were used. These stimuli were presented at horizontal and vertical meridians, and at meridians inclined at 45° angles. The illuminance level was set at six levels: 0.01 lx-1000 lx. The evaluation method measured chromatic, white, and black components as well as the hue component of the stimuli. Results show that the color zone of the retina extended further into the periphery with increasing illuminance; the response of opponent colors y-b was shown to be greater than that of the opponent colors r-g.     

A realistic coronary artery phantom for particle image velocimetry

Myocardial infarction results from the rupture of an atherosclerotic plaque, which occurs in response to both mechanical stress and inflammatory processes. In order experimentally observe flow into atherosclerotic coronary artery morphologies, a novel technique for molding realistic compliant phantom featuring injection-molded inclusions and multiple layers has been developed. This transparent phantom allows for particle image velocimetry (PIV) flow analysis and can supply experimental data to validate computational fluid dynamics algorithms and hypothesis.     

Real-time color holographic interferometry devoted to 2D unsteady wake flows

A new optical technique based on real time holographic interferometry in true colors has been implemented around the transonic wind tunnel of the ONERA-Lille center to analyze 2D unsteady wake flows. Tests realized in color interferometry, real time and double exposure, use simultaneously three wavelengths of a continuous waves laser (argon and krypton mixed) and holograms are recorded on silver-halide single-layer panchromatic Slavich PFG03c plates. The very principle of real-time true color holographic interferometry uses three primary wavelengths (red, green and blue) to record, under no-flow conditions, the interference among the three measurement beams and the three reference beams simultaneously on a single reference hologram. After the holographic plate is developed, it is placed on the test setup again in the position it occupied during exposure and the hologram is illuminated again by the three reference beams and three measurement beams. A flat, uniform color can then be observed behind the hologram. So a horizontal, vertical, or even circular fringe pattern can be formed and the achromatic central fringe can be made out very clearly. The single color is used to determine the path difference zero on the interferograms. The flow studied was the unsteady flow downstream of a cylinder placed crosswise in the test section. A sequence of hundred interferograms was recorded on the flow around the cylinder at Mach 0.37. The vortex formation and dissipation phases can be seen very clearly, along with the fringe beat to either side of the cylinder.     

Sorption of Zn(II) and Cd(II) by chelating resins: Comparison of three resins

Ion-exchange resins, especially chelating resins are used for pre-concentration of metal ions in trace analysis as well as for radiochemical separations following neutron activation of a variety of environmental samples. As part of a systematic study of the sorption characteristics of chelating resins, sorption of Zn(II) and Cd(II) by three chelating resins were studied for various acid conditions in nitrate and chloride media. Both Zn(II) and Cd(II) showed similar behavior. Under higher acid conditions, maximum sorption occurred in 3M HCl solutions. Under low acid conditions, the sorption increased with pH. Chelex 100 gave the highest sorption among the three resins. This revised version was published online in July 2006 with corrections to the Cover Date.     

Combined effects of clay modifications and compatibilizers on the formation and physical properties of melt‐mixed polypropylene/clay nanocomposites

The melt mixing technique was used to prepare various polypropylene (PP)‐based (nano)composites. Two commercial organoclays (denoted 20A and 30B) served as the fillers for the PP matrix, and two different maleated (so‐called) compatibilizers (denoted PP‐MA and SMA) were employed as the third component. The results from X‐ray diffraction (XRD) and transmission electron microscope (TEM) experiments revealed that 190 °C was an adequate temperature for preparing the nanocomposites. Nanocomposites were achieved only if specific pairs of organoclay and compatibilizer were simultaneously incorporated in the PP matrix. For example, PP/20A(5 wt %)/PP‐MA(10 wt %) and PP/30B(5 wt %)/SMA(5 wt %) composites exhibited nanoscaled dispersion of 20A or 30B in the PP matrix. Differential scanning calorimetry (DSC) results indicated that the organoclays served as nucleation agents for the PP matrix. Generally, their nucleation effectiveness increased with the addition of compatibilizers. The thermal stability enhancement of PP after adding 20A was confirmed with thermogravimetric analysis (TGA). The enhancement became more evident as a suitable compatibilizer was further added. However, for the 30B‐included composites, thermal stability enhancement was not evident. The dynamic mechanical properties (i.e., storage modulus and loss modulus) of PP increased as the nanocomposites were formed; the properties increment corresponded to the organoclay dispersion status in the matrix. © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 4139–4150, 2004