Optical fiber acoustic sensing multiplexing system based on TDM/SFDM

We propose a system of time-division multiplexing(TDM) and spatial frequency-division multiplexing(SFDM). Extrinsic Fabry–Perot interferometric sensors are applied to detect weak acoustic signals. The broadband source is employed, the light from it is modulated by a pulse signal sequence and is efficiently amplified by semiconductor optical amplifiers. Experimental results show that the equivalent noise pressure spectrum level is-97.2 d B re 1 rad/√Hz below 1250 Hz, and the cross talk between two sensors in one TDM channel is-32.7 d B with a cavity length difference of 60 μm. The number of sensors in this multiplexing system can theoretically reach 160.     

Boundedness of semilinear Duffing equations at resonance in a critical situation

In this paper, we propose a sufficient and necessary condition for the boundedness of all the solutions for the equation $\ddot{x}+n^{2}x+g(x)=p(t)$ with the critical situation that $|{\int }_0^{2\pi }p(t)e^{?int}dt|=2|g(+\infty )?g(?\infty )|$ on g and p, where $n\in {\mathbb{N}}^{+}$, $p(t)$ is periodic and $g(x)$ is bounded.     

DFT mechanistic study of the H2‐assisted chain transfer copolymerization of propylene and p‐methylstyrene catalyzed by zirconocene complex

DFT computations have been performed to investigate the mechanism of H₂‐assisted chain transfer strategy to functionalize polypropylene via Zr‐catalyzed copolymerization of propylene and p‐methylstyrene (pMS). The study unveils the following: (i) propylene prefers 1,2‐insertion over 2,1‐insertion both kinetically and thermodynamically, explaining the observed 1,2‐insertion regioselectivity for propylene insertion. (ii) The 2,1‐inserion of pMS is kinetically less favorable but thermodynamically more favorable than 1,2‐insertion. The observation of 2,1‐insertion pMS at the end of polymer chain is due to thermodynamic control and that the barrier difference between the two insertion modes become smaller as the chain length becomes longer. (iii) The pMS insertion results in much higher barriers for subsequent either propylene or pMS insertion, which causes deactivation of the catalytic system. (iv) Small H₂ can react with the deactivated [Zr]?pMS?PP_n facilely, which displace functionalized pMS?PP_n chain and regenerate [Zr]? H active catalyst to continue copolymerization. The effects of counterions are also discussed. © 2014 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2015 , 53, 576–585     

Facile fabrication of fast recyclable and multiple self‐healing epoxy materials through diels‐alder adduct cross‐linker

A reversibly cross‐linked epoxy resin with efficient reprocessing and intrinsic self‐healing was prepared from a diamine Diels‐Alder (DA) adduct cross‐linker and a commercial epoxy oligomer. The newly synthesized diamine cross‐linker, comprising a DA adduct of furan and maleimide moieties, can cure epoxy monomer/oligomer with thermal reversibility. The reversible transition between cross‐linked state and linear architecture endows the cured epoxy with rapid recyclability and repeated healability. The reversibly cross‐linked epoxy fundamentally behaves as typical thermosets at ambient conditions yet can be fast reprocessed at elevated temperature like thermoplastics. As a potential reversible adhesive, the epoxy polymer with adhesive strength values about 3 MPa showed full recovery after repeated fracture‐thermal healing processes. The methodology explored in this contribution provides new insights in modification of conventional engineering plastics as functional materials. © 2015 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2015 , 53, 2094–2103