A microporous membrane-based continuous generation system for trace-level standard mixtures of atmospheric gases.

A reliable and convenient system to generate accurate and stable standard gas mixtures of various atmospheric compounds at parts-per-billion levels has been developed. The system is of simple design; the generator is a coil consisting of an inner tube of microporous polytetrafuluoroethylene (PTFE) membrane tubing and an outer tube of silicone tubing. An aqueous solution of the given compound continuously flows through the inner microporous tube and the purge gas flows through the annulus between the inner and outer tubes. In addition to the generation of gas mixtures based on Henry's law, the proposed flow-type system offers generation based on chemical reactions, leading to a distinct advantage of the availability of continuous sources of various compounds. The generation system was tested for preparing standard gas mixtures of HCHO and H2O2 on the basis of Henry's law, and those of HNO2, NO, and SO2 on the basis of chemical reactions. A stable generation of the desired low concentrations of various kinds of gas mixtures can be readily achieved by adjusting the concentration of the solution without the use of high-dilution flow.     

Vibrational properties of hexagonal boron nitride: inelastic X-ray scattering and ab initio calculations

The phonon dispersion relations of bulk hexagonal boron nitride have been determined from inelastic x-ray scattering measurements and analyzed by ab initio calculations. Experimental data and calculations show an outstanding agreement and reconcile the controversies raised by recent experimental data obtained by electron-energy loss spectroscopy and second-order Raman scattering.     

Rapid determination of fumagillin residues in honey by liquid chromatography-tandem mass spectrometry using the QuEChERS method

A new, rapid, and efficient method for determining the fumagillin residues in honey was developed. The samples extracted were analyzed using LC/MS/MS. Chromatographic separation of fumagillin was performed in gradient mode on a C8 column (100 x 2.0 mm, 5 microm) at 40 degrees C. The mobile phase consisted of a mixture of 2 mM ammonium formate-0.01% formic acid solution and methanol; the flow rate was set to 0.2 mL/min. Under these conditions, it was possible to measure fumagillin and its isomers as a single peak. The sample preparation procedure used is based on the QuEChERS (quick, easy, cheap, effective, rugged, and safe) method, which is fast (approximately 30 min) and uses less organic solvent. The fumagillin was extracted with acetonitrile containing 0.1% formic acid, then purified using a solid-phase extraction method with an Oasis mixed-mode weak anion-exchange cartridge. The overall recovery of fumagillin ranged from 88.1 to 99.4%; the intra- and interassay CVs were <4.5% and <4.9%, respectively. The LOQ was 0.1 microg/kg. LC/MS/MS coupled with the QuEChERS method showed strong potential as a method for determining fumagillin residues in honey.     

Study of γ d → π + π − d Reaction in an Energy Region of 0.67 ≤ E γ ≤ 1.08 GeV

Double charged pion photoproductions from the deuteron have been studied at Research Center for Electron Photon Science (ELPH), Tohoku University. Tagged photon beams in an energy range of 0.67 ≤ E _γ ≤ 1.08 GeV were impinged on the liquid deuteron target. Produced charged particles were observed with the Neutral Kaon Spectrometer2 (NKS2). The γ d → π ⁺ π ^? d process was clearly separated among the three charged tracks. We obtained the photon energy dependence of the normalized yields of this process.     

Study of Strangeness Photoproduction on the Neutron in the Threshold Region

Photoproduction of the neutral kaon on the deuteron has been investigated at the Research Center for Electron Photon Science, Tohoku University. We constructed the Neutral Kaon Spectrometer-2 for the detection of charged particles from the decay of the neutral kaon and the hyperon. We obtained a momentum distribution of K ⁰ with the inclusive measurement. It was consistent with the previous measurement. The total cross section of γ + d → K ⁰ + Λ + p was estimated from the measured integral cross section of γ + d → Λ + X. The total cross section with respect to the photon energy was compared with the theoretical calculations. It favored the Saclay-Lyon A model calculation with the ratio of the neutral to charged coupling constants of the axial-vector meson, K ₁, as ~ ?1.5. The energy dependence and the magnitude of the total cross section were similar to the total cross section of γ + p → K ⁺ Λ.     

Removal and regeneration of aqueous divalent cations by boehmite

Boehmite (Al(OH)O) was employed for the removal of aqueous Mg(2+), Cu(2+), Cd(2+), Pb(2+), and Co(2+) at 298 K. Although boehmite was able to remove these divalent cations, the greater removal rate with boehmite of Pb(2+) (28.7%) than with Mg(2+), Cu(2+), Cd(2+), and Co(2+) (5.6, 25.3, 10.9, and 13.3%, respectively) was observed under acidic conditions. Under stronger alkaline conditions, in which the lead species was completely dissolved, a greater removal rate of Pb(2+) (more than 80%) was observed under the corresponding conditions employed for the acidic conditions. The removed lead species could not be dissolved from boehmite in an acidic solution while an evident dissolution of lead species was detected using an aqueous NaOH solution. The results shown in the present study reveal that boehmite can be employed as a reagent for the removal and regeneration of aqueous metal cations.     

Sequential stir bar sorptive extraction for uniform enrichment of trace amounts of organic pollutants in water samples

A novel extraction procedure for stir bar sorptive extraction (SBSE) termed sequential SBSE was developed. Compared to conventional SBSE, sequential SBSE provides more uniform enrichment over the entire polarity/volatility range for organic pollutants at ultra-trace levels in water. Sequential SBSE consists of a SBSE performed sequentially on a 5-mL sample first without modifier using one stir bar, then on the same sample after addition of 30% NaCl using a second stir bar. The first extraction with unmodified sample is mainly targeting solutes with high Kow (logKow>4.0), the second extraction with modified sample solution (containing 30% NaCl) is targeting solutes with low and medium Kow (logKow<4.0). After extraction the two stir bars are placed in a single glass desorption liner and are simultaneously desorbed. The desorbed compounds were analyzed by thermal desorption and gas chromatography-mass spectrometry (TD-GC-MS). Recovery of model compounds consisting of 80 pesticides (organochlorine, carbamate, organophosphorus, pyrethroid, and others) for sequential SBSE was evaluated as a function of logKow (1.70-8.35). The recovery using sequential SBSE was compared with those of conventional SBSE with or without salt addition (30% NaCl). The sequential approach provided very good recovery in the range of 82-113% for most of the solutes, and recovery less than 80% for only five solutes with low Kow (logKow<2.5), while conventional approaches (with or without salt addition) showed less than 80% recovery for 23 and 41 solutes, respectively. The method showed good linearity (r2>0.9900) and high sensitivity (limit of detection: <10ngL(-1)) for most of the model compounds even with the scan mode in the MS. The method was successfully applied to screening of pesticides at ngL(-1) level in river water samples.     

Energy-saving drying technology for porous media using liquefied DME gas

Process design and energy requirement for a practical plant are investigated for an energy-saving drying (dewatering) process invented by the authors in 2002 for high-moisture porous materials. The basic concept of the process involves the extraction of water from a high-moisture porous material by bringing it in physical contact with liquefied dimethyl ether (DME) at room temperature. Water content of DME asymptotically increases to the saturation value and the high-moisture porous material is dried almost perfectly. DME from the DME-water mixture is vaporized by decompression. DME and water are separated by flash distillation. DME vapor is compressed and cooled in a heat exchanger, and the latent heat of condensation is reused to vaporize the DME in the heat exchanger. Multistage compression and multistage flash distillation are employed. After compression, the temperature of DME is less than 50?°C. Because specific heat ratio of DME is only 1.11, the energy consumption of the compressor is reduced. Considering the adiabatic efficiency of the compressor and the net thermal efficiency, the total energy for dewatering is about 1100 kJ per 1-kg-water-content of the material being dewatered This process has significant potential and is compact than the existing dewatering processes.