Why define atoms in real space?

The physics of a system is determined by a variation of the action integral, i.e., by a variation of the space–time volume integral of the Lagrange function. If one demands that the properties of an atom in a molecule be derived from physics, the atom must generate its own space–time volume, requiring that its boundaries be defined in real space. The variations in the action are related to the actions of generators of infinitesimal unitary transformations. In the general case, the action integral is altered by generators acting in both the spacelike and timelike surface bounding the space–time volume, whereas for a total isolated system, the physics is totally determined by their action in just the spacelike surfaces at the two time endpoints. It is shown and illustrated for a one-dimensional system that the definition of an atom corresponds to the possibility of choosing a subsystem in such a way that the contributions to the change in action resulting from the evolution in time of its spatial boundaries vanishes identically. The properties of these subsystems and of the total system of which they are a part are, therefore, determined by one and the same action principle. This choice of subsystem corresponds to the possibility of augmenting the Lagrange function by the divergence of the gradient of the electron density a step that, while leaving the equations of motion unchanged, modifies the generating operators in the required manner. © 1994 John Wiley & Sons, Inc.     

Three-dimensional atom probe study of the segregation behaviour of Ni91Pt9 alloy after sputtering

To investigate local ordering and segregation phenomenon in a Ni91Pt9-alloy after sputtering and annealing a 3D optical atom probe (OAP) has been used. The specimen tips have been prepared from polycrystalline samples. To sputter the samples a separate preparation chamber with a scannable Ar-sputter-gun is connected to the OAP vessel. When necessary, the sample can be electrically heated to induce segregation and cure the altered layer. After a heat treatment of a Ni91 at. %Pt 9 at.% specimen at 1100 K the surface of a (111)-oriented specimen is enriched in platinum by a factor of two in relation to the bulk. The phenomenon of short-range ordering has been investigated on the surface and in the subsurface volume. A 3D reconstruction of this annealed NiPt specimen shows regions with high concentration of platinum that gives an indication at short-range ordering. Uniform sputtering of the tip without a heat treatment induces a decisive depletion of Pt on the surface and the following subatomic layers. The atom-probe results of specimens in thermal equilibrium are in close agreement to further surface sensitive results obtained from Ion Scattering Spectroscopy (ISS) and Auger Electron Spectroscopy (AES).     

Spin effects in instanton models

Nonperturbative nolocal structure of QCD vacuum is well described by instanton model. Specific helicity and flavor structure of zero modes of quarks, in instanton field allows simultaneously to explain some important features of low-and high-energy hadron phenomemology. The basic characteristics of hadron spectrum, partonic sum rules, heavyquark potential etc within the instanton liquid model are briefly discussed.     

Study of the charge-exchange reactions\pi ^ - p \to (\pi ^0 ,\eta ,\eta \prime )n at 63 GeV

Muon electron pairs were detected in an Al multiplate spark chamber, exposed to a neutrino beam from the CERN PS. The leptons were not accompanied by other particles, except occasionally by protons. The background came mainly from muon associated π⁰ production, with one decay gamma lost. It was determined empirically, together with the small contribution from υ _e reactions. For electron energies above 2 GeV the background is 5.7±1.5 events, whereas 18 (μe)-candidates have been observed. Hence the effect is established, with a rate of about 10^?4 as compared to the muonic reactions above 3 GeV. Charm creation as the origin of this (μe)-production process is excluded; heavy neutral lepton production does not fit the kinematics observed. Instead the events are compatible with the two-body decay of an object with variable invariant mass of order 1 GeV, possibly resulting from axion interactions.     

A comparison of steady-state evoked potentials to modulated tones in awake and sleeping humans.

Steady-state evoked potential responses were measured to binaural amplitude-modulated (AM) and combined amplitude- and frequency-modulated (AM/FM) tones. For awake subjects, AM/FM tones produced larger amplitude responses than did AM tones. Awake and sleeping responses to 30-dB HL AM/FM tones were compared. Response amplitudes were lower during sleep and the extent to which they differed from awake amplitudes was dependent on both carrier and modulation frequencies. Background EEG noise at the stimulus modulation frequency was also reduced during sleep and varied with modulation frequency. A detection efficiency function was used to indicate the modulation frequencies likely to be most suitable for electrical estimation of behavioral threshold. In awake subjects, for all carrier frequencies tested, detection efficiency was highest at a modulation frequency of 45 Hz. In sleeping subjects, the modulation frequency regions of highest efficiency varied with carrier frequency. For carrier frequencies of 250 Hz, 500 Hz, and 1 kHz, the highest efficiencies were found in two modulation frequency regions centered on 45 and 90 Hz. For 2 and 4 kHz, the highest efficiencies were at modulation frequencies above 70 Hz. Sleep stage affected both response amplitude and background EEG noise in a manner that depended on modulation frequency. The results of this study suggest that, for sleeping subjects, modulation frequencies above 70 Hz may be best when using steady-state potentials for hearing threshold estimation.     

Estimation of multivariate binary density using orthogonal functions

In this paper, the authors studied certain properties of the estimate of Liang and Krishnaiah (1985, J. Multivariate Anal. 16, 162–172) for multivariate binary density. An alternative shrinkage estimate is also obtained. The above results are generalized to general orthonormal systems.     

A New Distribution Function for Risk Analysis

This paper presents an alternative to the beta continuous probability distribution for risk analysis. Particular attention has been given to two major applications of distributions, namely project management risk and critical path analysis (PERT). In conjunction with the beta, the triangular and normal distributions are frequently employed in order to give sufficient robustness to risk analysis. The beta distribution, as used in PERT, has a major theoretical implementation flaw. The new distribution was developed to give a possible alternative method of assessing risk. It is shown that the requirement to estimate the most pessimistic variate may be replaced by the probability to exceed the mode. Proposals for other simplifications in risk analysis are discussed. Practical means to validate the most appropriate distributions for risk analysis are outlined, and a cost-data case study is included.     

Multicriteria decision making under uncertainty

Formalization for problems of multicriteria decision making under uncertainty is constructed in terms of guaranteed and weak estimates. A relevant definition of the vector maximinimax value is given. Parameterization and approximation of maximum, minimax, and maximinimax values based on the inverse logical convolution are suggested. An application for multicommodity networks is considered. Received: December 13, 2000 / Accepted: August 21, 2001?Published online May 8, 2002     

VIBRATION OF TWISTED AND CURVED CYLINDRICAL PANELS WITH VARIABLE THICKNESS

A numerical procedure, with an exact strain-displacement relationship of twisted and curved cylindrical panels having variable thickness derived by considering the Green strain tensor on general shell theory, is presented using the principle of virtual work and the Rayleigh-Ritz method with algebraic polynomials as in-plane and transverse displacement functions. The accuracy and applicability of the procedure are verified by comparing the present results with previous experimental and theoretical results for several panels. The effects of variation ratio of thickness in chordwise and lengthwise directions, twist, and curvature both in two directions aforementioned on vibrations of cylindrical panels are studied in detail, and typical vibration mode shapes are plotted to demonstrate the effects.