A microfluidic chip integrated with a microoptical lens fabricated by femtosecond laser micromachining

We report on the integration of microlens and microfluidic channels in fused silica glass chip using femtosecond laser micromachining. The main process includes three procedures: (1) femtosecond laser scanning for forming a hemispherical surface and a Y-shaped channel in the fused silica glass; (2) chemical etching of the sample for removal of the modified areas; and (3) oxyhydrogen (OH) flame polish for smoothening the surface of the microlens. In addition, we demonstrate that the fabricated microlens exhibits good imaging performance with a 5× magnification, showing great potential in future lab-on-a-chip applications.     

Reduction of thermal fluctuations in a cryogenic laser interferometric gravitational wave detector

The thermal fluctuation of mirror surfaces is the fundamental limitation for interferometric gravitational wave (GW) detectors. Here, we experimentally demonstrate for the first time a reduction in a mirror's thermal fluctuation in a GW detector with sapphire mirrors from the Cryogenic Laser Interferometer Observatory at 17 and 18 K. The detector sensitivity, which was limited by the mirror's thermal fluctuation at room temperature, was improved in the frequency range of 90 to 240 Hz by cooling the mirrors. The improved sensitivity reached a maximum of 2.2×10(-19) m/√Hz at 165 Hz.     

Optimization of the surface texture for silicon carbide sliding in water

Surface texturing has been recognized as an effective means to improve the tribological performances of sliding surfaces. Usually, generation additional hydrodynamic pressure to increase the load carrying capacity is regarded as the most significant effect of surface texture. In the case of silicon carbide sliding against identical material in water, the experimental results indicate that surface texture is also helpful to improve the running-in progress to smooth the contact surfaces, showing another reason to result in low friction. Based on the consideration of enhancing the generation of hydrodynamic pressure and improving running-in progress, a surface texture pattern, which was combined with large (circle, 350 μm in diameter) and small (rectangular, 40 μm in length) dimples, was designed to maximize the texture effect on the load carrying capacity of SiC surfaces sliding in water. The friction coefficient of such textured surface was evaluated and compared with that of untextured and those only with large or small dimples only. The friction reduction mechanisms of the patterns with different dimples in size are discussed.     

χ polarization induced in molecular glass of conjugated compound by all-optical poling

The paper presents the first report on χ⁽²⁾ polarization induced in molecular glass of conjugated compound by all-optical poling. Transparent thin film of molecular glass of 1,4-bis[2-[4-[N,N-di(p-tolyl)amino]phenyl]vinyl]benzene (BTAPVB) was prepared using a spin-cast technique. Dipolar as well as octupolar components in BTAPVB contributed to the formation of photoinduced χ⁽²⁾ polarization. Growth rate of χ⁽²⁾ polarization has good linear relation with E_ω⁴E_2ω, which suggested that the simultaneous processes of two-photon (ω + 2ω) and three-photon (ω + ω + ω) excitation on the same electronic level contributed to the formation of photoinduced χ⁽²⁾ polarization.     

Studies on adhesion characteristics and corrosion behaviour of vinyltriethoxysilane/epoxy coating protective system on aluminium

The corrosion stability of vinyltriethoxysilane/epoxy coating protective system on aluminium is strongly related to the strength of bonds forming at the metal/organic coating interface. This article is a study of adhesion, composition, electrochemical and transport properties of epoxy coatings electrodeposited on bare aluminium and aluminium pretreated by vinyltriethoxysilane (VTES) during exposure to 3% NaCl. The VTES film was deposited on aluminium surface from 2% vinyltriethoxysilane solution during 30 s. From the values of adhesion strength (pull-off test), time dependence of pore resistance and coating capacitance of epoxy coating (impedance measurements) and diffusion coefficient of water through epoxy coating (gravimetric liquid sorption measurements), the influence of VTES sublayer on the corrosion stability of the electrodeposited epoxy coating was shown.The work discusses the role of the VTES pretreatment in the enhanced adhesion and corrosion stability of epoxy cataphoretic coating. The electrochemical results showed that the aluminium pretreatment by VTES film improved barrier properties of epoxy coating (greater pore resistance and lower coating capacitance). The lower value of diffusion coefficient of water through epoxy coating indicates the lower porosity, while the smaller adhesion reduction points to better adhesion of epoxy coating on aluminium pretreated by VTES film. The composition of the deposited coatings investigated by XPS enabled the clarification of the bonding mechanism.     

Jet ejection from droplets near the Leidenfrost temperature

Abstract  

Droplets impinging on a hot surface that is near the Leidenfrost temperature were experimentally investigated. Ejection of jets from the top of the droplet was observed during the transient interaction between the droplet and a hot wall. We term this phenomenon jet ejection from droplets. When the bottom of the droplet initially impacts the hot surface, a jet is to be ejected from the top of the droplet. The jet ejection occurred only at low impact velocities and around the wetting limit temperature. It was not observed when droplets were dropped from large heights or when the surface was at a high temperature.     

Visualization of Magnetization Transfer Effect in Polyethylene Glycol Impregnated Waterlogged Wood

To visualize the condition of impregnation of polyethylene glycol (PEG) in waterlogged wood, we demonstrated magnetic transfer (MT) magnetic resonance imaging (MRI) through a series of process of PEG impregnation. Three different samples were examined; reference wood, 10 cm cut wood, and 5 cm cut wood. During this study, the upper section sample was kept immersed in water, for the middle and lower sections the concentration of PEG solution was changed at 20 wt% intervals from 20 to 100 wt%. The impregnated periods of each PEG solution concentration were 14 days. Then, MR imaging were performed with/without MT pulse. The MTR value for both 10 cm- and 5 cm-samples were shown to decrease at 20 wt% PEG at peak concentration. When the sample volume was large, e.g., 10 cm-sample, the MTR value decreased to 100 wt% PEG concentration. In contrast, when a sample volume was small, e.g., 5 cm-sample, MTR value decreased to 60 wt% PEG concentration. In conclusion, MTR analysis makes it possible to nondestructively visualize and evaluate the inner condition concerning the PEG impregnation method for waterlogged wood.     

Complexability of o-bisguanidinobenzenes with arsenic and phosphoric acids in solution and solid states, and the potential use of their immobilized derivatives as solid base ligands for metal salts and arsenic acid

The role of o-bisguanidinobenzenes (BGBs) as new Brønsted base ligands for arsenic and phosphoric acids was examined. In solution state, complexation was evaluated by Job’s plot in ¹H NMR experiment, indicating a 1:1 complex formation, whereas in solid state crystalline structures of complexes obtained were addressed by X-ray crystallographic analysis and/or solid state ¹³C NMR experiment, in which 1:2 complexes between the BGB and the acid components were normally formed. Based on these results, Merrifield and Hypogel^® resin-anchored BGBs were designed and prepared as the corresponding polymer-supported host ligands. Evaluation of their coordination ability with metal salts (ZnCl₂ and CoCl₂) and arsenic acid in aqueous media by ICP-MS showed that the latter Hypogel^® resin-anchored BGBs acted as effective immobilized base ligands.