光电倍增管脉冲性能研究

采用外腔式电光开光,调制主动照相探测光源,使光电倍增管处于脉冲工作状态下,以提高光电倍增管的输出幅度和动态范围,改善信号的信噪比,同时避免样品和探测器受长时间强激光照射.对滨松H6780光电倍增管进行了调试,使其线性输出电流由静态的0.1mA提升到脉冲状态的4.4mA,信噪比提高4.5倍.该技术对其他光敏探测有借鉴意义.     

Giant shot-like voltage noise in high current density Nb–AlOx–Nb superconducting tunnel junctions

The flat voltage noise component of current biased, high-transparency Nb/AlO_x/Nb superconducting tunnel junctions has been investigated at frequencies up to 70 kHz. Several aspects of the analyzed phenomena suggest the presence of current noise effects induced by the discreteness of the charge carriers. At subgap voltages, where excess currents occur, a behavior coherent with a multiple Andreev reflection-assisted transport through the tunnel barrier has been found. However, the measured charge values exceed any theoretical prediction.     

Nuclear Resonant Scattering into the New Millennium

Hyperfine Interactions - The technique of nuclear resonant scattering has spread out in various fields during the previous years. Those fields, which have rapidly developed and attracted the...     

Preliminary design of high-power wave-guide/transmission system for multimegawatt CW requirements of 100 MeV proton LINAC

Development of a 100 MeV CW proton LINAC has been planned at CAT. This LINAC will be needing CW rf power in the frequency ranges of 350 MHz and 700 MHz for its RFQ and DTL/CCDTL/SFDTL structures respectively. The power to the accelerating structures will be produced by either 1 MW CW or 250 kW CW klystrons/inductive output tubes (HOM IOTs). The power needed by respective feed points in the structure is max. 250 kW which will be powered by splitting the power from 1 MW klystron/klystrode into four channels by using a wave-guide system. In case of using 250 kW tubes the power to the structures will be provided directly from each tube. Two types of wave-guide transmission system have been considered, viz, WR 2300 for 350 MHz rf needs and WR 1500 for 700 MHz rf needs. The typical wave-guide system has been designed using the 1 MW CW klystron followed by wave-guide filter, dual directional coupler, high-power circulator, three 3 dB magic TEE power dividers to split the main channel into four equal channels of 250 kW each. Each individual channel has dual directional couplers, flexible wave-guide sections and high power ceramic vacuum window. The circulator and each power divider is terminated into the isolated ports by high power CW loads. Out of the four channels three channels have phase shifters. Present paper describes the technological aspects and design specifications-considerations for these stringent requirements.     

Dynamic response of permalloy/Cu/Co magnetoresistive sandwiches

The dynamic response of trilayer magnetoresistive permalloy/Cu/Co films was studied by high-frequency permeability spectra measurements. The resonance frequency is shown to depend on the interlayer copper thickness. This dependence is related to exchange coupling between permalloy and cobalt and the interaction field is estimated using the Landau–Lifschitz–Gilbert model.     

Mode beating in spot-size converter lasers

An anomalous modulation in the wavelength spectrum has been observed in lasers with spot-size converters. This intensity modulation is shown to be caused by beating between the fundamental lasing mode and radiation modes in the taper. This results in a periodic modulation in the net gain spectrum, which causes wavelength jumps between adjacent net gain maxima, and a drive current dependent spectral width that is expected to affect system performance. The amplitude of this spectral modulation is reduced significantly by either using an angled rear-facet which reflects the beating radiation modes away from the laser axis, or by using a nonlinear, adiabatic taper.     

Potential for micromachined actuation of ultra-wide continuously tunable optoelectronic devices

Tailored scaling represents a principle of success that, both in nature and in technology, allows the effectiveness of physical effects to be enhanced. Mutation and selection in nature are imitated in technology, e.g. by model calculation and design. Proper scaling of dimensions in natural photonic crystals and our fabricated artificial 1D photonic crystals (DBRs, distributed Bragg reflectors) enable efficient diffractive interaction in a specific spectral range. For our optical microsystems we illustrate that tailored miniaturization may also increase the mechanical stability and the effectiveness of spectral tuning by thermal and electrostatic actuation, since the relative significance of the fundamental physical forces involved considerably changes with scaling. These basic physical principles are rigorously applied in micromachined 1.55-μm vertical-resonator-based devices. We modeled, implemented and characterized 1.55-μm micromachined optical filters and vertical-cavity surface-emitting laser devices capable of wide, monotonic and kink-free tuning by a single control parameter. Tuning is achieved by mechanical actuation of one or several air-gaps that are part of the vertical resonator including two ultra-highly reflective DBR mirrors of strong refractive index contrast: (i) Δn=2.17 for InP/air-gap DBRs (3.5 periods) using GaInAs sacrificial layers and (ii) Δn=0.5 for Si₃N₄/SiO₂ DBRs (12 periods) with a polymer sacrificial layer to implement the air-cavity. In semiconductor multiple air-gap filters, a continuous tuning of >8% of the absolute wavelength is obtained. Varying the reverse voltage (U=0–5 V) between the membranes (electrostatic actuation), a tuning range of >110 nm was obtained for a large number of devices. The correlation of the wavelength and the applied voltage is accurately reproducible without any hysteresis. In two filters, tuning of 127 and 130 nm was observed for about ΔU=7 V. The extremely wide tuning range and the very small voltage required are record values to the best of our knowledge. For thermally actuated dielectric filters based on polymer sacrificial layers, Δλ/ΔU=-7 nm/V is found. Received: 10 May 2002 / Published online: 8 August 2002     

Magnetic anisotropy of textured CrO2 thin films investigated by X-ray magnetic circular dichroism

Highly a-axis-textured CrO₂ films have been deposited on Al₂O₃ (0001) substrates by chemical vapor deposition. CrO₂ has been found to have highly a-axis (010)-oriented columnar growth on a Cr₂O₃ (0001) initial layer. The six-fold surface symmetry of the Cr₂O₃ initial layer leads to three equivalent in-plane orientations of the a-axis-oriented CrO₂ unit cell. We report Cr L_2,3 X-ray magnetic circular dichroism data along the surface normal and at 60° off-normal sample orientation. For a 60° sample alignment, a strong increase of the projected orbital moment could be observed for unoccupied majority t_2g states using moment analysis. Therefore, the c axis is identified as the intrinsic magnetic easy axis of CrO₂. In addition, a small spin moment and a very strong magnetic dipole term T_z have been found. Received: 8 January 2002 / Accepted: 8 January 2002