An axial flow cyclone to remove nanoparticles at low pressure conditions

In this study, the axial flow cyclone used in Tsai et al. (2004) was further tested for the collection efficiency of both solid (NaCl) and liquid (OA, oleic acid) nanoparticles. The results showed that the smallest cutoff aerodynamic diameters achieved for OA and NaCl nanoparticles were 21.7 nm (cyclone inlet pressure: 4.3 Torr, flow rate: 0.351 slpm) and 21.2 nm (5.4 Torr, 0.454 slpm), respectively. The collection efficiencies for NaCl and OA particles were close to each other for the aerodynamic diameter ranging from 25 to 180 nm indicating there was almost no solid particle bounce in the cyclone. The 3-D numerical simulation was conducted to calculate the flow field in the cyclone and the flow was found to be nearly paraboloid. Numerical simulation of the particle collection efficiency based on the paraboloid flow assumption showed that the collection efficiency was in good agreement with the experimental data with less than 15% of error. A semi-empirical equation for predicting the cutoff aerodynamic diameter at different inlet pressures and flow rates was also obtained. The semi-empirical equation is able to predict the cutoff aerodynamic diameter accurately within 9% of error. From the empirical cutoff aerodynamic diameter, a semi-empirical square root of the cutoff Stokes number, , was calculated and found to be a constant value of 0.241. This value is useful to the design of the cyclone operating in vacuum to remove nanoparticles.     

Mesoporous nanotube aggregates obtained from hydrothermally treating TiO2 with NaOH

Nanotube aggregates with high porosity were prepared from hydrothermal treatment of TiO₂ particles in NaOH at 130 °C, followed by HCl rinsing to different pH values. Pore structure of the aggregates, which were mainly mesoporous, was characterized by analyzing the N₂ sorption isotherm with different methods including the t-plot and density function theory. The surface area, pore volume and mean pore size of the aggregates increased with the rinsing acidity to reach a maximum (e.g. 400 m²/g in surface area) at pH 1.6 and then decreased with further increase of the acidity. The crystalline phase and composition of the aggregates were, as well, significantly affected by the acidity of the post-treatment rinsing. Large-surface area aggregates were of loosely-attached nanotubes, composed of both anatase TiO₂ and H₂Ti₂O₅·H₂O, obtained under a mildly acidic rinsing condition, while basic or highly acidic conditions resulted in the formation of closely coagulated dense structures consisting of different crystalline phases.     

Magnetic,structural and electrical properties of ordered and disordered Co50Fe50 films

Co₅₀Fe₅₀ films with thickness varying from 100 to 500 Å were deposited on a glass substrate by sputtering process, respectively. Two kinds of CoFe films were studied: one was the as-deposited film, and the other the annealed film. The annealing procedure was to keep the films at 400 °C for 5 h in a vacuum of 5×10⁻⁶ mbar. From the X-ray study, we find that the as-deposited film prefers the CoFe(1 1 0) orientation. Moreover, the body-centered cubic (bcc) CoFe(1 1 0) line is split into two peaks: one corresponding to the ordered body-centered tetragonal (bct) phase, and the other, the disordered bcc phase. After annealing, the peak intensity of the ordered bct phase becomes much stronger, while that of the disordered bcc phase disappears. The annealing has also caused the ordered CoFe(2 0 0) line to appear. When the amount of the ordered bct phase in Co₅₀Fe₅₀ is increased, the saturation magnetization (M_s) and coercivity (H_c) become larger, but the electrical resistivity (ρ) decreases. From the temperature coefficient of resistance (TCR) measurement, we learn that the bct grains in the CoFe film start to grow at temperature 82 °C.     

A Revisit on the Derivation of the Particular Solution for the Differential Operator ∆2 ± λ2

In this paper, we applied the polyharmonic splines as the basis functions to derive particular solutions for the differential operator ∆² ± λ². Similar to the derivation of fundamental solutions, it is non-trivial to derive particular solutions for higher order differential operators. In this paper, we provide a simple algebraic factorization approach to derive particular solutions for these types of differential operators in 2D and 3D. The main focus of this paper is its simplicity in the sense that minimal mathematical background is required for numerically solving higher order partial differential equations such as thin plate vibration. Three numerical examples in both 2D and 3D are given to validate particular solutions we derived.     

Improvement of photoluminescence mechanism of CTA-treated Si-implanted SiO2 films by using RTA

In this paper, a shift in the photoluminescence (PL) peak from blue to near-infrared region was observed in the Si⁺-implanted 400-nm-thick SiO₂ films with the rapid thermal annealing (RTA) method only. As the Si⁺-fluence was 1×10¹⁶ ions/cm², a blue band was observed in the films after RTA at 1050 °C for 5 s in dry-N₂ atmosphere; then, the band shifted from blue to orange upon increasing the holding temperature of RTA to 1250 °C in the films after the isochronal RTA in dry N₂. Furthermore, while the fluence was increased to 3×110¹⁶ ions/cm² and the holding temperature was at the same range between 1050 and 1250 °C, the PL peak occurred between red and near-infrared regions. Although the RTA and conventional thermal annealing (CTA) methods produce a similar mechanism, the CTA method needs a much longer annealing-time and a higher Si⁺-implanted dose than the RTA method for producing the same shift and intensity of PL peak from the as-implanted sample. Therefore, the RTA method can produce the mechanism in the Si⁺-implanted sample with the PL energy between blue and near-infrared band in place of the CTA method.     

Using photoelectron emission microscopy with hard-X-rays

We present several successful test cases of using photoelectron emission microscopy (PEEM) for photon energy up to 25 keV. First, the full extended X-ray absorption fine structure analysis was implemented in areas as small as 100 μm² for transition-metal K edge absorption spectra and, therefore, demonstrated the feasibility of combining structural and chemical analysis with hard-X-ray absorption spectroscopy with high lateral resolution. We also show that PEEM can be used in a transmission (radiography) mode as an imaging detector for hard-X-ray. This approach again leads to the unprecedented 0.3 μm lateral resolution, particularly critical for the use of coherence-based phase contrast techniques in real time X-ray radiology.     

Euler calculations with embedded Cartesian grids and small-perturbation boundary conditions

This study examines the use of stationary Cartesian mesh for steady and unsteady flow computations. The surface boundary conditions are imposed by reflected points. A cloud of nodes in the vicinity of the surface is used to get a weighted average of the flow properties via a gridless least-squares technique. If the displacement of the moving surface from the original position is typically small, a small-perturbation boundary condition method can be used. To ensure computational efficiency, multigrid solution is made via a framework of embedded grids for local grid refinement. Computations of airfoil wing and wing-body test cases show the practical usefulness of the embedded Cartesian grids with the small-perturbation boundary conditions approach.     

Determination of 129I in cement-solidified radwastes using neutron activation

The purpose of this study is to develop a neutron activation method to determine trace amounts of ¹²⁹I in cement-solidified radwastes. The radwaste samples were alkaline fused using KOH and then ¹²⁹I and iodine carrier were chemically separated by solvent extraction before and after neutron irradiation. Both stable iodine (¹²⁷I) and ¹²⁹I can be activated by neutrons through ¹²⁷I (n, 2n) ¹²⁶I and ¹²⁹I (n, γ) ¹³⁰I reactions; their activated radionuclides were counted together with a high-purity germanium detector. The chemical recovery yields ranged from 30 to 60 %, and it was found that more than 99.9 % of interfering radionuclides can be removed using solvent extraction after neutron irradiation. The minimum detectable amounts can be lowered to less than 1 mBq g^?1, which is superior to low energy γ-ray spectrometry by a factor of >10², on average. The established technique can be applied to re-evaluation of ¹²⁹I content in radwastes that can be re-classified to lower classes, and the cost for designing a final disposal facility can be significantly reduced.     

Fused-ring and linking group effects of proton donors and acceptors on simple H-bonded liquid crystals

Two fused-ring structures, 6-decyloxy-2-naphthoic acid C₁₀ONA (3) and 6-dodecyloxyisoquinoline IS (8), were synthesized and utilized as proton donor and acceptor moieties to construct a series of simple mesogenic supramolecules. The other complementary hydrogen-bonded (H-bonded) moieties are benzoic acids, thiophenecarboxylic acid and pyridines containing different alkyl chain lengths connected by ether and ester linkages, i.e. 4-alkoxybenzoic acid C _n OBA (1), terephthalic acid monoalkyl ester C _n COOBA (2), 2,5-thiophenedicarboxylic acid monodecyl ester C₁₀COOTHA (4), 4-alkoxypyridine C _n OP (6) and isonicotinic acid alkyl ester C _n COOP (7). Several series of simple mesogenic supramolecular dimers were constructed from 1:1 molar ratios of proton donors (C _n OBA, C _n COOBA, C₁₀ONA and C₁₀COOTHA) and proton acceptors (IS, C _n OP and C _n COOP), though the proton acceptor C _n COOP induced phase separation in all complexes. In order to investigate their fused-ring and linking group effects on the mesogenic properties of the H-bonded complexes, analogous simple supramolecular structures are compared. Supramolecular architecture and the distinct mesomorphism of these simple H-bonded liquid crystalline materials were confirmed by polarizing optical microscopy, DSC and powder X-ray diffraction experiments.