Swelling-shrinking behavior of a polyampholyte gel composed of positively charged networks with immobilized polyanions

Polyampholyte gels were prepared by free radical polymerization of aqueous monomer solutions with the following composition: 69% N-isopropylacrylamide (thermosensitive neutral monomer), 1% N,N'-methylenebisacrylamide (cross-linker), 15% 1-vinylimidazole (cationic monomer), and either 15% acrylic acid (AAc, anionic monomer) or poly(acrylic acid) (PAAc, polyanion). We thus obtained two sorts of polyampholyte gels; that is, G1 with immobilized PAAc and G2 with randomly copolymerized AAc. The equilibrium swelling ratio (Qe) was studied as a function of the pH, NaCl concentration, and temperature. Also studied was the kinetics of swelling and shrinking in response to a sudden pH change. The significant results obtained were as follows: (i) A fully collapsed state was observed at pH 4.5-9.0 for G1 and at pH 4.5-7.0 for G2. (ii) Below and above these pH ranges, both gels were in a swollen state; therefore, an isoelectric point (pI) appeared in a wide pH range. (iii) At alkaline pH regions where a hysteresis was observed in the Qe versus pH curves of G1 and G2 as the pH was first increased then decreased, G1 exhibited very slow swelling-shrinking kinetics. (iv) An increase in the NaCl concentration allowed the gel to swell at pH approximately pI (antipolyelectrolyte behavior) but to shrink at pHs below and above the pI range (polyelectrolyte behavior). (v) The magnitude of the salt-induced shrinking of G1 is smaller than that of G2 at pH 10 and at NaCl concentrations > 0.01 M. (vi) At pH 10, an increase in the temperature from 35 to 50 degrees C led to a shrinking change of G1 but not of G2. These results were found to be explicable in terms of a different distribution of negative charges within the polyampholyte gel network.     

Leaching behavior of metal-containing species in residual oils with different organic solvents

The leaching behavior of two different residual oils is investigated with 24 organic solvents including alkanes, aromatics, esters, ethers ketones, alcohols and nitrogen compounds. A 2-g portion of sample oil is shaken with 20 ml of the organic solvent. The leaching of the organic matrix of the oil is determined by weighing the dissolved organic matrix after removal of solvent. The leaching of vanadium, iron and nickel was determined by flame atomic absorption spectrophotometry after ashing of the dissolved fraction. The leaching of those metals depends strongly on the solvent used; for example, vanadine is almost completely leached into toluene, but only slightly into methanol. The leaching of iron is poor compared with that of vanadium or nickel. In most solvents, leaching of those metal-containing species is poorer than that of organic material. Exceptionally, N,N-dimethylformamide is more efficient in leaching vanadium species than organic material.     

X-ray diffraction analysis of nonequilibrium states in crystals: observation of an unstable conformer in flash-cooled crystals

Some molecules with a molecular skeleton similar to that of stilbenes and azobenzenes show orientational disorder in the crystals. If the disorder is dynamic, a conformational interconversion takes place through a pedal motion. In this study X-ray diffraction analyses of (E)-stilbene (1) and azobenzene (2) were carried out at various temperatures. We succeeded in observing thermodynamic nonequilibrium states that were generated by fast freezing of the conformational interconversion at low temperatures. The populations of the two conformers in crystals of 1 at 90 K varied with the cooling rate. Flash cooling of a crystal of 2 from room temperature to 90 K made it possible to observe the minor unstable conformer that does not exist in the equilibrium state at the same temperature.     

Synthesis of porphyrin-introduced silica gels by sol-gel process

Using a hydroxyl group appended free base porphyrin derivative (HP), porphyrin-introduced silica gels were synthesized by a sol-gel process. The HP content in the materials linearly increased with increasing the HP concentration. Meanwhile, free base tetraphenylporphyrin (TPP) with no hydroxyl groups were almost not incorporated into the silica gels. These facts suggested that the interaction between hydroxyl groups of the HP molecules and silica network is considerably strong. The UV-vis characters of HP-introduced materials were almost the same as pure HP molecules. The Beer's plot indicated that the HP molecules in the materials are dispersed.     

Ceric-ion-initiated grafting of methyl methacrylate onto (1 → 5)-α-D-ribofuranan and (1 → 5)-α-D-xylofuranan

We report herein studies of grafting of MMA onto (1 → 5)-α-D -ribofuranan and (1 → 5)-α-D -xylofuranan by ceric ion initiation both in water and in dimethyl sulfoxide (DMSO). In aqueous medium, the graft polymer having high grafting (%) can be obtained easily without adding any nitric acid. The degradation of polysaccharide by the acidic ceric ion solution is not serious; 73–82% of its original molecular weight remained after the polymerization. In DMSO, graft polymers having lower grafting (%) and lower molecular weight of grafts were obtained.     

Distribution of pirarubicin in human blood.

We investigated the distribution and stability of pirarubicin in human blood obtained from 12 healthy volunteers. The distribution of pirarubicin into blood cells showed marked temperature- and concentration-dependencies and the Arrhenius plot for pirarubicin uptake in blood was biphasic. Therefore, pirarubicin appears to be taken up into blood cells by a carrier-mediated system. Pirarubicin was mainly enzymatically metabolized to pirarubicinol in blood cells, but pirarubicin was not metabolized into doxorubicin in either blood or plasma. On the other hand, in plasma, pirarubicin was degraded to unknown inactive compounds instead of pirarubicinol. It is therefore suggested that blood cells serve to protect against the degradation of pirarubicin into inactive compounds in blood. Accordingly, when the monitoring of pirarubicin and its active metabolites is carried out in patients, both blood and plasma must be frozen immediately after blood collection.     

Regioselective synthesis and properties of novel [60]fullerene bisadducts containing a dibenzocrown ether moiety

The reactions of [60]fullerene with bis-o-quinodimethane precursors 3, 4, and 5 containing a dibenzo-18-crown-6, 24-crown-8 and 30-crown-10 moiety, respectively, were investigated. Both 3 and 4 provided trans-4 bisadducts 6a and 7a, respectively, as major product, though the selectivity in the latter was lower than that in the former. As minor product, 6b (cis-2) was produced from 3, while 7c (e) as well as 7b (cis-2) were produced from 4. Precursor 5 exclusively afforded e bisadduct 8 without any other regioisomers. These bisadducts showed different ionophoric properties from one another; for instance, 6a and 7b exhibited a high complexing ability toward the K+ ion, while 6b hardly showed complexation with any alkali metal ions. The selectivity coefficients (K(Na,K)(pot)) of 6a and 7b toward K+ over Na+ ion, determined with an ion-selective electrode, were much higher than that of dibenzo-18-crown-6.     

Monitoring nano-flow rate of water by atomic emission detection using helium radio-frequency plasma

Recently, high-performance nano-scale flow pumping systems have been developed for micro and miniaturized analysis systems. A novel device capable of measuring and monitoring nanoliter scale flow rates has been required for the further development of the pumping system. In this study, an atomic emission detector using helium radio-frequency plasma (RFP-AED) was used for the measurement of the nanoliter scale flow rate of water by quantitatively detecting the emission from hydrogen in the water molecules. Monitoring nano-flow rates of water in the range up to 1.0 microl min(-1), and the change in the flow rate by the indication of the ratio of the emissions of H (656.3 nm) and He (667.8 nm) were successful. At present, the lowest flow rate that could be determined reproducibly was 4 nl min(-1) calculated as five times the standard deviation of the background noise. Additionally, similar evaluations for the deviation of each flow rate by using the RFP-AED and a flow-injection system were produced.     

Diacetylene-containing polymers,II. Polyesters and polyurethanes containing m,m′-butadiynylenedibenzyl groups

Diacetylene-containing polyesters and polyurethanes were prepared by the reaction of m,m-butadiynylenedibenzyl alcohol with isophthaloyl chloride, sebacoyl chloride, hexamethylene diisocyanate and 2,4-tolylene diisocyanate. Their thermal behavior was studied by optical microscope and differential scanning calorimetry (DSC). The polyesters were crystalline. The polyurethane prepared from hexamethylene diisocyanate and polyphthalates crystallized on cooling from their melts. All turned a reddish brown color on heating at temperatures above 200°C, and prolonged heating led to a black resin, but thermal decomposition could not be avoided. Irradiation by γ-ray and UV light at room temperature deepened the color of the films, but the polymerization of the diacetylene groups was not appreciable. Simultaneous heating and irradiation was necessary to obtain transparent, amorphous, wine red colored films.