Preparation and certification of the new reference materials; plastics (disk form, JSAC 0621-0625) for determination of mercury using x-ray fluorescent analysis.

The Japan Society for Analytical Chemistry has developed some new plastic certified reference materials (CRMs) for the analysis of mercury in polyester disks using XRF analysis. These CRMs (named as JSAC 0621-0625) were prepared by casting polyesters including a toluene solution of organometallic compounds as a standard. Concentrations of the five levels of mercury ranged from 0 to 250 mg/kg. Homogeneity tests of prepared disks had shown excellent results. Interlaboratory comparison study for the certification was performed by 15 laboratory participants. The z-scores in robust statistical method was applied for the evaluation of outliers. The certified values were assigned after discarding outliers. The uncertainties of certified values were determined as the confidence levels of 95%.     

Viscoelasticity and birefringence of polyisoprene

The complex Young's modulus, E^*(ω), and the complex strain-optical coefficient, O^*(ω), which is the ratio of the birefringence to the strain, were measured for polyisoprene (PIP) over a frequency range of 1 ～ 130 Hz and a temperature range of 22 ～ ?100°C. The imaginary part of O^*, O″, was positive at low frequencies and negative at high frequencies. The real part, O′, was always positive and showed a maximum. The complicated behavior of O^* could be understood by the assumption that E^* = E_R^* + E_G^* and O^* = C_RE_R^* + C_GE_G^*, where E_R^* and E_G^* were complex quantities and C_R and C_G were constants. The C_R value, equal to the ordinary stress-optical coefficient measured in the rubbery plateau zone, was 2.0 × 10^?9 Pa^?1. The C_G value, defined as the ratio O″/E″ in the glassy zone, was ?1.1 × 10^?11 Pa^?1. The E_G^*, which was the major component of E^* in the glassy zone, showed almost the same frequency dependence as that of polystyrene and polycarbonate. The E_R^*, which was dominant in the rubbery zone, was described well by the bead-spring theory. The temperature dependence of the E_G^* was stronger than that of the E_R^*. This difference caused the breakdown of the thermorheological simplicity for E^* and O^* around the glass-to-rubber transition zone. © 1995 John Wiley & Sons, Inc.     

A study of corrosion on a rotating iron disk electrode

Corrosion of iron in slightly acidified sodium sulphate solutions (mainly pH 4.5) in the open air was studied with a rotating disk electrode method at room temperature.Microscopic observations of corroded iron disk surfaces in the pH 4.5 solution revealed that iron initially corrodes locally with the formation of round pits of 10–30 μm in diameter and of(0.6–1.3) × 10³ in number per apparent square centimetre followed by the U-shaped brown protective wall formation of precipitates (rust) outside the pits. Each protective wall is formed along the lines of flow of the solution adjacent to the iron surface and each pit is located near the upstream end of the wall. Steady state of corrosion sets in when the parts of surface area surrounded by the wall are completely covered with a microscopically non-porous rust film.The amount of iron in the rust film and the total amount of corrosion of iron including that in the film increase parabolically with the increase in the time of immersion. The amount of iron in the film increases in proportion to the total amount of corrosion independently of the speed of rotation of the disk electrode even in the steady state.The fraction of area of iron surface not covered with the film decreases with time and reaches a certain fixed value in the steady state: the value is smaller at higher rotational speed. The corrosion rate is proportional to the uncovered area, as the corrosion is near the steady state. The pH of the bulk solution increases as corrosion progresses.The corrosion rate of iron can be well interpreted by assuming that the rate is controlled by the diffusion of oxygen from the bulk solution to the surface of iron and that the rust film on iron impedes the diffusion of oxygen.     

Preparation and certification of JAC river water reference material for trace element analysis

 The Japan Society for Analytical Chemistry has recently issued a river water-certified reference material (CRM) for use in the ultratrace analysis of elements in fresh water. The river water CRM consists of a set of two (natural and spiked) 500-ml samples. The natural water is certified for Pb, Cr, As, Cu, Fe, Mn, Zn, B and Al at their sub-μg/l levels, while the spiked water is intended for use in the regulatory analysis of tap water and fresh water. Key words River water · Trace element analysis · Regulatory analysis · Reference materials     

Second-order nonlinear optical properties from poled silicate channel-waveguide

Thin film waveguides of germanosilicate glass are fabricated byrf-sputtering. Second-order nonlinearity ofd ₃₃=3.2 pm/V is obtained from electrically poled film, and the lifetime of the nonlinearity is found to be310 years. The poled channel-waveguide is prepared and the Cerenkov-type phase-matched frequency doubling is successfully observed.     

Salting-in of alcohols in aqueous solutions by tetraalkylammonium bromides at the freezing temperature

The freezing-point depression of the ternary systems tetraalkylammonium bromides-t-butanol-water for the first five homologs of R₄NBr was measured. In the case of Bu₄NBr, the effect of size of the alcohol (methahol ton-butanol) was also investigated. From the corresponding freezing-point data for the binary systems the apparent salting constants were calculated. The true salting constantsk _s were obtained by extrapolation to infinite dilution. These are all very close to zero at the freezing temperature. From the corresponding thermochemical data the temperature dependence ofk _s was calculated, and above 5°C all the R₄NBr salts int-butanol; the salting-in increases with temperature and with the size of the hydrophobic cations. The scaled-particle theory is at present the only one which can account semiquantitatively for the temperature dependence of the salting-in effect. On leave of absence from Chemistry Department, The University, Sheffield S3 7HF, England To whom correspondence should be addressed.     

Two novel dicoumaro-p-menthanes from Gerbera piloselloides (L.) CASS

Two new type dicoumarins (dicoumaro-p-menthanes), named dibothrioclinins I (1) and II (2) were isolated from the roots and rhizomes of Gerbera piloselloides (L.) CASS., collected in Yunnan Province, China. Their structures were elucidated on the basis of MS, 1D ((1)H-NMR, (13)C-NMR, DEPT and NOE) and 2D ((1)H-(1)H COSY, HMQC, HMBC) NMR spectral analyses. The relative structures of the two compounds were established by NOE difference spectroscopy and further confirmed by single-crystal X-ray diffraction studies.     

Preparation of octadecyl modified column gels using heat-treated silicas and their retention behaviour in high-performance liquid chromatography

Summary The effect of silanol groups on three types of octadecylmodified column gels using heat-treated silicas by calcination has been studied by high-performance liquid chromatography. After heat-treating at 180°C, 500°C and 950°C, the silicas treated with octadecyldimethylchlorosilane were used for the measurement of physical and chemical analysis. From elemental carbon analysis data, the reactive silanol group concentrations, _OH(s), were determined to be 2.0 in the 180°C treated silica, 2.1 in the 500°C treated silica and 1.6 in the 950°C treated silica, respectively (original silica: mean pore diameter 116 Å, specific surface area 298 m²/g, pore volume 1.22 ml/g, particle size 5.0 m). The separation factors, , of pyridine versus phenol were measured to be 0.79 on 180°C treated silica, 0.91 on 500°C treated silica and 1.98 on 950°C treated silica, using acetonitrile-water mixtures as the eluent. And then, on the basis of the physico-chemical and chromatographic data, the three types of octadecyl modified column gels using heat-treated silicas by calcination have been compared.     

Some aspects of plasma copolymerization of acetylene with N2 and/or water

Plasma polymerizations of mixture of acetylene-N₂, acetylene-H₂O, were investigated by using an electrodeless glow discharge from a 13.5-MHz radiofrequency source. Properties of plasma polymers were examined as functions of mole ratios of N₂ and/or H₂O to acetylene. The concentration of trapped free radicals and the internal stress in a plasma polymer decreased as the mole ratio of N₂ or H₂O increased. Water showed the most pronounced effects in those properties at the mole ratio of 0.3. Gas permeabilities increased by the copolymerization of N₂ and/or H₂O. Surface energies were also investigated by analysis of contact angles of liquids. Copolymerization of N₂ caused a remarkable increase in polar contribution of surface energy. Some fundamental aspects of flow-rate pressure relationship of mixed gases are presented.