Identification of degradation products in loxoprofen sodium adhesive tapes by liquid chromatography-mass spectrometry and dynamic pressurized liquid extraction-solid-phase extraction coupled to liquid chromatography-nuclear magnetic resonance spectroscopy

Rapid and unambiguous identification of three degradation products (DP-1, DP-2 and DP-3) found in heat-stressed loxoprofen sodium adhesive tapes (Loxonin tapes) was achieved by LC-MS and dynamic pressurized liquid extraction (PLE)-solid-phase extraction (SPE) coupled to LC-NMR without complicated isolation or purification processes. The molecular formulae of the degradation products were determined by accurate mass measurements and product ion analyses and on-line hydrogen/deuterium (H/D) exchange experiments provided information about changes in the degradation of loxoprofen. To compensate for the low sensitivity of NMR, on-line dynamic PLE-SPE was employed and higher concentrations of degradation products trapped on the SPE column were afforded in a shorter time than they would be in such time-consuming sample preparations as pre-concentration after extraction. The loop-storage procedure was used in the LC-NMR analysis to allow the acquisition of the (1)H spectra of the three degradation products in one chromatographic run without affecting the peak separation and to avoid the carry-over of previously eluted DP-1 of high concentration by washing the NMR detection cell prior to the measurement of the DP-2 spectrum. Based on the resulting (1)H NMR spectra in combination with the MS results, DP-1 was successfully identified as an oxidation product having an oxodicarboxylic acid structure formed by the cleavage of the cyclopentanone ring of loxoprofen, DP-2 as a cyclopentanone ring-hydroxylated loxoprofen and DP-3 as a loxoprofen l-menthol ester.     

Excited-state structure and dynamics of 1,3,5-tris(phenylethynyl)benzene as studied by Raman and time-resolved fluorescence spectroscopy

Excited-state structure and dynamics of 1,3,5-tris(phenylethynyl)benzene (TPB) have been studied in n-hexane and n-heptane solutions. Time-resolved fluorescence spectra, fluorescence anisotropy, and lifetime of TPB were recorded with femtosecond to nanosecond time resolution. Raman depolarization ratio was also measured to elucidate a nonplanar structure of the ground state. Two fluorescence components, the short-lived component with 150 fs lifetime and the long-lived component with 10 ns lifetime, were observed. The analysis of the fluorescence anisotropy values combined with the Raman depolarization data has led to a conclusion that TPB is primarily excited to a short-lived excited singlet state with a nonplanar structure, and then it relaxes to a long-lived excited singlet state with a 3-fold axis. A rapid structural change from a nonplanar to a planar structure is suggested to take place in the process of relaxation.     

Grid-based energy density analysis: implementation and assessment

Grid-based energy density analysis (grid-EDA) that decomposes the total energy into atomic energies by a space-partitioning function is proposed. The kinetic energy, nuclear attraction, and exchange-correlation functional are evaluated on grid points and are split into atomic contributions. To reduce numerical errors in the conventional scheme of numerical integration, the electronic Coulomb and HF exchange interactions are evaluated by the pseudospectral method, which was first applied to an ab initio method by Friesner [Chem. Phys. Lett. 116, 39 (1985)], and are decomposed into atomic contributions. Grid-EDA using the pseudospectral method succeeds in ensuring less than 1 kcalmol error in total energies for small molecules and providing reliable atomic energy contributions for the problematic lithium cluster, which exhibits a strong basis-set dependence for Mulliken-type EDA. Also, site-dependent atomization energies are estimated by grid-EDA for cluster models such as Li(48), C(41)H(60), and Mg(32)O(32). Grid-EDA reveals that these models imitate crystal environments reasonably because atomization energies estimated from the inner atoms of the models are close to the experimental cohesive energies.     

Stimulated Raman scattering and four-wave Raman mixing seeded by a supercontinuum generated in dibromomethane using picosecond and femtosecond laser sources

Stimulated Raman emission from liquid dibromomethane (vibrational Raman shift frequency, 588 cm⁻¹) is introduced into hydrogen gas (rotational Raman shift frequency, 587 cm⁻¹) as a seed beam, in order to generate numerous rotational lines by four-wave Raman mixing. Unexpectedly, a supercontinuum, which is generated by self-phase modulation in dibromomethane, acted as a seed beam to exclusively generate vibrational lines; the rotational lines are generated only when the supercontinuum is minimal. The former is explained by a competition between the high-gain vibrational and low-gain rotational Raman effects when strongly seeded by a supercontinuum. The latter is explained by stimulated Raman gain under the seed effect exclusively to the first-Stokes rotational line.     

Color adjustment algorithm adapted to the spectral reflectance estimation method

We are developing a daily health monitoring system that uses mobile phones with cameras and analyzes physiological conditions from R, G, and B intensity levels. However, since it is affected by various imaging conditions of the image input, color correction is required for accurate health monitoring. Therefore, we developed and validated a colorcorrection algorithm to derive reliable color information by correcting the spectral reflectance using the Wiener estimation and a color chart.     

Exact diagonalization studies on two-band minimal model for iron-based superconductors

In order to explore a superconducting mechanism on iron-based superconductors, we numerically study a two-band minimal model considering two degenerate d_xz and d_yz orbitals on Fe atom. We perform exact diagonalization on a two-band and two-leg square ladder totally composed of 10 lattice sites, which is computationally equivalent to 4-leg 20-sites square-Hubbard-ladder. Consequently, we find that a robust pairing occurs in a wide parameter range when the intra-orbital repulsive interaction becomes smaller than the inter-orbital one. Moreover, the obtained binding energy can grow into much larger value than that obtained in the single band Hubbard model depending on the parameter range.     

Modified ion exchange separation for tungsten isotopic measurements from kimberlite samples using multi-collector inductively coupled plasma mass spectrometry

Tungsten isotope composition of a sample of deep-seated rock can record the influence of core-mantle interaction of the parent magma. Samples of kimberlite, which is known as a carrier of diamond, from the deep mantle might exhibit effects of core-mantle interaction. Although tungsten isotope anomaly was reported for kimberlites from South Africa, a subsequent investigation did not verify the anomaly. The magnesium-rich and calcium-rich chemical composition of kimberlite might engender difficulty during chemical separation of tungsten for isotope analyses. This paper presents a simple, one-step anion exchange technique for precise and accurate determination of tungsten isotopes in kimberlites using multi-collector inductively coupled plasma mass spectrometry (MC-ICP-MS). Large quantities of Ca and Mg in kimberlite samples were precipitated and removed with aqueous H(2)SO(4). Highly pure fractions of tungsten for isotopic measurements were obtained following an anion exchange chromatographic procedure involving mixed acids. That procedure enabled efficient removal of high field strength elements (HFSE), such as Hf, Zr and Ti, which are small ions that carry strong charges and develop intense electrostatic fields. The tungsten yields were 85%-95%. Advantages of this system include less time and less use of reagents. Precise and accurate isotopic measurements are possible using fractions of tungsten that are obtained using this method. The accuracy and precision of these measurements were confirmed using various silicate standard rock samples, JB-2, JB-3 and AGV-1.