Coercivity analysis in R17Fe83−χBχ magnets

We studied the coercivity in magnets of composition R₁₇Fe_83−χB_χ (R = Nd, Pr and χ = 8, 30), using measurements of the coercive field H_c, its angular dependence, and the magnetic viscosity coefficient S_v, for temperatures between 4.2 and 500 K. The results are discussed in relation to a model which does not specifically consider the detailed mechanisms involved in magnetization reversal, but which provides information about the magnetic properties in the activation volume v where magnetization reversal is initiated. It is concluded that the ordering temperature in v tends to be slightly smaller than in the bulk and that the room temperature anisotropy in v is not strongly reduced with respect to the bulk value. Finally, a direct evaluation of the dipolar interactions is in good agreement with results obtained from H_c(T).     

Ferroelectric polarization switching in nylon-11

Cold-drawn Nylon-11 films, which were prepared by stretching the melt-quenched films to a draw ratio of 2.8: 1 at room temperature, were found to exhibit an electric displacement versus electric field hysteresis loop. The results confirmed that the Nylon-11 film exhibited ferroelectric behavior at or below room temperature. The coercive fields were 65, 98, 125, 160, and 215 MV/m at 20, 0, ?20, ?40, and ?60°C and the remanent polarization at ?20°C (where there was considerably less dc conduction) was 56 mC/m². Switching of the polarization was almost completed within 20 ms.     

AUTOMATED WIND TUNNEL MEASUREMENTS

It is common practice in power transmission to use bundled overhead electrical conductors because the lower rate of corona discharge, compared with single conductors, makes the bundle attractive for high voltages. However, secondary problems may arise from the vibrations induced by the aerodynamic forces which act on the leeward conductors as a result of their immersion in the wake of a windward conductor. Thus, in addition to possible aeolian and galloping oscillations observed for a single conductor, bundle conductors may also be subjected to wake-induced oscillations. ^1,2 Although extensive research has been done on the aeroelastic behavior of single and bundled conductors which are bare, little is known about the galloping or wake oscillation characteristics of given bundle conductors which, depending upon the environmental conditions during the formation of ice, may have five or so representative shaped cross-sections. One important task involves the aerodynamic quasi-static force and moment measurements in a wind tunnel using full scale conductor cross-sections each of which must be rotated through many angles at different spacings. Such measurements are repetitive as well as tediously time consuming and, hence, are beneficially automated. A reliable, accurate and inexpensive automated apparatus is described in this paper which permits the aerodynamic measurements to be performed efficiently and without intervention. Most importantly, it relieves the operator of the usual responsibility for manually controlling the separation and orientation of the sections as well as the need to manually compensate fluctuations in the free stream air speed. For simplicity, the apparatus is detailed in the context of a twin bundle conductor.     

Fiber formation via solution spinning of the cellulose/ammonia/ammonium thiocyanate system

Fiber formation via the cellulose/ammonia/ammonium thiocyanate system by wet spinning has been investigated. This report presents a characterization of the structure and tensile properties of fibers spun under various coagulation conditions. Microscopic observations showed that the molecular size of coagulant was the dominant factor governing the crosssectional shape of the fibers. Density, birefringence, and crystallinity data indicated that a higher cellulose concentration and lower coagulation temperature favored development of a fiber with a denser and more oriented structure. Under optimum conditions, a welldefined fibrillar structure was obtained. Fiber tensile property measurements suggested the existence of a linear relationship between the fiber breaking tenacity and the product of the square of the Hermans' orientation factor and the infrared crystallinity index.     

Identification of peroxyacetic acid uroporphyrin I in the urine of patients with congenital erythropoietic porphyria by liquid chromatography and mass spectrometry

A new porphyrin, peroxyacetic acid uroporphyrin I, has been isolated from the urine of patients with congenital erythropoietic porphyria by reversed phase high performance liquid chromatography. The porphyrin was characterized by high resolution mass spectrometry and by typical chemical reactions of a peroxyacid.     

Low-energy ion-assisted control of interfacial structures in metallic multilayers

A molecular dynamics method has been used to simulate the argon ion-assisted deposition of Cu/Co/Cu multilayers and to explore ion beam assistance strategies that can be used during or after the growth of each layer to control interfacial structures. A low-argon ion energy of 5–10 eV was found to minimize a combination of interfacial roughness and interlayer mixing (alloying) during the ion-assisted deposition of multilayers. However, complete flattening with simultaneous ion assistance could not be achieved without some mixing between the layers when a constant ion energy approach was used. It was found that multilayers with lower interfacial roughness and intermixing could be grown either by modulating the ion energy during the growth of each metal layer or by utilizing ion assistance only after the completion of each layers deposition. In these latter approaches, relatively high-energy ions could be used since the interface is buried and less susceptible to intermixing. The interlayer mixing dependence upon the thickness of the over layer has been determined as a function of ion energy.