Time-dependent conformational changes in adsorbed albumin and its effect on platelet adhesion

Recent studies have shown that platelets can adhere to adsorbed albumin (Alb) through a receptor-mediated mechanism, but only if the Alb undergoes more than a critical degree of adsorption-induced unfolding. The objectives of this research were to investigate whether Alb that was initially adsorbed in a manner that induced unfolding that was less than this critical level would undergo further unfolding with time and, if so, whether this would induce the onset of platelet adhesion once this critical level was exceeded. To address these questions, CD spectropolarimetry was used to monitor the structure of Alb on OH- and CH(3)-functionalized alkanethiol self-assembled monolayer surfaces, with the Alb initially adsorbed under conditions resulting in degrees of unfolding that were below this critical level, and then the adsorbed Alb layers were aged over 6 months in sterile physiological saline at 37 °C. Platelet adhesion to Alb was quantified at selected time points via a lactate dehydrogenase (LDH) assay. The results indicate that an adsorbed Alb layer does undergo further structural changes with increasing residence time and supports platelet adhesion once it unfolds beyond the previously determined critical level. These results may be relevant to the clinically observed problem of the onset of late-thrombosis, which occurs on cardiovascular implants such as drug-eluting stents.     

Propagation of Alfvén surface waves along the ionospheric plasma slab with the effect of gravity

Ionospheric regions connecting the neutral gas atmosphere have been considered to be an incompressible plasma slab surrounded by incompressible plasma on one side and neutral gas on the other side. The effect of gravity on Alfvén surface waves in the slab geometry is studied. As a special case, the propagation of ASW along the plasma-neutral gas interface is also discussed. The existence of two modes of surface waves has been identified and their characteristic behaviour affected by the gravity has been discussed.     

Separation of lanthanides using ion-interaction chromatography with HDEHP coated columns

A rapid and high resolution separation of lanthanides by HPLC technique has been developed using Di-(2-ethylhexyl) phosphoric acid (HDEHP) coated reverse phase column and a-hydroxy isobutyric acid as the complexing reagent for elution. A gradient elution technique has been developed for achieving the separation of the entire lanthanide series. Isocratic elution procedure has also been developed for the separation of lighter (La to Gd) as well heavier lanthanides (Lu to Tb). This paper describes the separation methods developed and their application for the determination of lanthanides in a fission product mixture.     

Energy‐induced polymorphic changes in poly(vinylidene fluoride): How ultrasonication results in polymer with predominantly γ phase

Self‐polarized poly(vinylidene fluoride) (PVDF) films were prepared via solution crystallization technique wherein the polymorphism of the films was controlled from α phase (>85%) to γ phase (>90%) by varying the time of ultrasonication. On increasing ultrasonication time up to 60 min, γ phase crystallites were found to be self‐aligned in the matrix while an equal proportion of α and γ phases coexist in the PVDF films ultrasonicated for 120 min. The phase conversion as well as inversion was evident from Fourier transform infrared, X‐ray diffraction, and differential scanning calorimetry analyses. Microscopic images of films ultrasonicated for 60 min showed a scrolled lamellar morphology while those sonicated for 120 min showed mixture of scrolled lamellar and spherulitic morphology. With the help of computational studies, it is explained that a large amount of energy is required for transforming trans‐gauche‐trans‐gauche into trans‐trans‐trans‐gauche conformation which is provided by ultrasonication. The mechanism of γ phase formation is proposed based on the experimental and theoretical approaches. Our studies show that just by tuning the time of ultrasonication, PVDF films with various morphologies can be processed; either one with predominantly electroactive γ phase with superior electrical properties or one with equal proportion of α and γ phases with superior mechanical properties. © 2018 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2019 , 57, 40–50     

Kinetic Evidence for the Influence of Subsurface Oxygen on Palladium Surfaces Towards CO Oxidation at High Temperatures

Transient state kinetics of the catalytic oxidation of CO with O₂ on Pd‐surfaces has been measured under isothermal conditions by using a molecular beam approach. Systematic studies were carried out as a function of reaction temperature and CO+O₂ composition. With sufficient kinetic evidence, we have demonstrated the positive influence of subsurface oxygen towards CO‐adsorption and oxidation to CO₂ at high temperatures (600–900 K) on Pd‐surfaces, and the likely electronic nature of the surface changes with oxygen in the subsurface. These studies also provide a direct proof for CO‐adsorption with a significantly reactive sticking coefficient at high temperatures on Pd‐surfaces exhibiting a significant subsurface O‐coverage.     

Isothermal kinetic study of nitric oxide adsorption and decomposition on Pd(111) surfaces: molecular beam experiments

The kinetics of NO adsorption and dissociation on Pd(111) surfaces and the NO sticking coefficient (s(NO)) were probed by isothermal kinetic measurements between 300 and 525 K using a molecular beam instrument. NO dissociation and N2 productions were observed in the transient state from 425 K and above on Pd(111) surfaces with selective nitrogen production. Maximum nitrogen production was observed between 475 and 500 K. It was found that, at low temperatures, between 300 and 350 K, molecular adsorption occurs with a constant initial s(NO) of 0.5 until the Pd(111) surface is covered to about 70-80% by NO. Then s(NO) rapidly decreases with further increasing NO coverage, indicating typical precursor kinetics. The dynamic adsorption - desorption equilibrium on Pd(111) was probed in modulated beam experiments below 500 K. CO titration experiments after NO dosing indicate the diffusion of oxygen into the subsurface regions and beginning surface oxidation at > or = 475 K. Finally, we discuss the results with respect to the rate-limiting character of the different elementary steps of the reaction system.     

Synthesis and characterization of polyurethane–polyvinylbenzyl chloride multiblock copolymers and their cationomers using a polyurethane macroiniferter

Polyurethane iniferter prepared from isocyanate end capped prepolymer and 1,1,2,2-tetraphenyl-1,2-ethanediol, has been used to polymerize vinylbenzyl chloride to obtain polyurethane-polyvinylbenzyl chloride multiblock copolymers. Formation of the block copolymers proceeds with increase in both molecular weight and conversion with increasing polymerization time showing that the polymerization proceeds via a “living” radical mechanism. The block copolymers so obtained were converted into their cationomers by the treatment of triethylamine. The block copolymers and their cationomers have been characterized by FTIR, FTNMR, TGA, and DSC studies. The effect of thermal energy on the molecular weight of the macroiniferter in the absence of monomer has been studied in order to understand the mechanism of formation of the block copolymers. © 1997 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 35: 1237–1244, 1997     

In situ synthesis of cobalt nanocrystal hierarchies in a transmission electron microscope

We report a versatile electron beam (e-beam) synthesis method for the local fabrication of ferromagnetic nanocrystals “on demand”. A localized irradiation in a transmission electron microscope (TEM) is used to convert a raw cobalt fluoride material into ferromagnetic metal by means of formation of a short-range ordered distribution of well-defined faceted three-dimensional (3D) cobalt nanocrystals on the carbon substrate. A range of sizes and morphologies can be obtained, depending on the size, intensity, and acceleration voltage of the e-beam and on the initial size/thickness of the 3D raw fluoride materials, with 300 kV acceleration voltage and thermionic LaB₆ emission found most favorable. The nanofabrication of locally quasi-monodispersed, small sized, and well-distributed 3D nanocrystals opens up the possibility to generate particle arrays on demand with desirable magnetic properties.