Using capillary electrophoresis for the determination of organic acids in Port wine

The simultaneous separation and determination of organic acids in several samples of white and red Port wines was performed by capillary zone electrophoresis using indirect UV detection with 2,6-pyridinedicarboxylic acid as a background electrolyte buffer. Operational parameters like migration time, temperature, voltage and capillary length were optimized. Sixteen samples of red wine and four samples of white wine were used to analyze for tartaric, malic, lactic, succinic and acetic acids using glyoxylic acid as the internal standard. The method is rapid, sensitive and quantitative, and time-consuming sample preparation, such as solid-phase extraction or liquid-liquid extraction procedure, is not required.     

Sol-gel ZrO2 coatings for chemical protection of stainless steel

ZrO₂ coatings deposited on 316 L stainless steel sheets were synthesized by sol-gel method using Zr(OC₃H₇)₄ as precursor and isopropanol, glacial acetic acid, and water as solvents for application with ultrasounds. Different solutions for dip-coating were prepared with compositions varying between 0.025 and 0.9 mol/dm³ of ZrO₂. X-ray diffraction shows that the films densified at 800°C are crystalline with a tetragonal structure. The thickness of the coatings varied from 0.35–0.75 m. The influence of the ZrO₂ coatings on the corrosion behavior of stainless steel substrates in aqueous NaCl was studied through potentiodynamic polarization curves at 1 mV/s. The values of the electrochemical parameters allow for an explanation of the role of the films in the increased resistance of steel against corrosion in moderately aggressive environments.     

Copper determination in biological materials by ETAAS using W-Rh permanent modifier

A tungsten-rhodium treatment on the integrated platform of a transversely heated graphite atomiser was used as a permanent chemical modifier for the determination of copper in biological materials by using digested samples as well as slurry sampling in electrothermal atomic absorption spectrometry. The W-Rh permanent modifier was as efficient as Pd+Mg(NO(3))(2) conventional modifier for obtaining good Cu thermal stabilisation in the digested and slurry samples. The permanent W-Rh modifier remained stable by approximately 300 and 250 firings when 20 mul of digested sample and 20 mul of slurry were delivered into the atomiser, respectively. In addition, the permanent modifier increased the tube lifetime up to 1370 and 744 analytical measurements in the digested and slurry samples, respectively. Also, when the W-Rh permanent modifier was employed, there was less variation of the slope of the analytical curves during the total atomiser lifetime, resulting in a decreased need of re-calibration during routine analysis, increasing the sample throughput, and consequently diminishing the variable analytical costs. Detection limits obtained with W-Rh permanent modifier were 0.64 and 0.33 mug g(-1) Cu for digested (dilution factor 100 ml g(-1)) and 1.0% m/v slurries of biological materials, respectively. Results for the determination of copper in the samples were in agreement with those obtained with decomposed sample solutions by using Pd+Mg(NO(3)), since no statistical differences were found after applying the paired t-test at the 95% level.     

Oxidation of Methanol on Pt,Pt–Ru,and Pt–Ru–Mo Electrocatalysts Dispersed in Polyaniline: An in situ Infrared Reflectance Spectroscopy Study

The electrochemical oxidation of methanol was investigated on a Pt–Ru–Mo catalyst with an in situ infrared reflectance spectroscopy. The electrocatalysts were prepared by an electrochemical deposition and dispersed in a conducting three-dimensional matrix of polyaniline (PAni). We observed that CO₂ is produced from methanol oxidation at 350 mV vs. RHE on PAni/Pt–Ru–Mo, which is 100 mV less negative than on PAni/Pt–Ru and 200 mV less than on PAni/Pt. The results suggest that Pt–Ru–Mo is less sensitive to CO_ADS poisoning than Pt–Ru and much more sensitive than Pt. Large differences are observed concerning the average wavenumber of _ADS between Pt–Ru–Mo, Pt–Ru, and Pt.     

Determination of arsenic compounds in beverages by high-performance liquid chromatography-inductively coupled plasma mass spectrometry

Arsenic compounds including arsenous acid (As(III)), arsenic acid (As(V)), dimethylarsinic acid (DMA) and monomethylarsonic acid (MMA) were separated by high-performance liquid chromatography (HPLC) and detected by inductively coupled plasma mass spectrometry (ICP-MS). A Hamilton PRX-100 anionic-exchange column and a pH 8.5 K₂HPO₄/KH₂PO₄ 5.0 × 10⁻³ mol L⁻¹ mobile phase were used to achieve arsenic speciation. The separation of arsenic species provided peaks of As(III) at 2.75 min, DMA at 3.33 min, MMA at 5.17 min and As(V) at 12.5 min. The detection limits, defined as three times the standard deviation of the lowest standard measurements, were found to be 0.2, 0.2, 0.3 and 0.5 ng mL⁻¹ for As(III), DMA, MMA and As(V), respectively. The relative standard deviation values for a solution containing 5.0 μg L⁻¹ of As(III), DMA, MMA and As(V) were 1.2, 2.1, 2.5 and 3.0%, respectively. This analytical procedure was applied to the speciation of arsenic compounds in drinking (soft drink, beer, juice) samples. The validation of the procedure was achieved through the analysis of arsenic compounds in water and sediment certified reference materials.     

Development of a rapid and specific assay for detection of busulfan in human plasma by high-performance liquid chromatography/electrospray ionization tandem mass spectrometry

A sensitive and specific assay for detection of busulfan in human plasma was developed. The assay is based on rapid isolation of busulfan by liquid-liquid extraction with ethyl acetate, and detection by high-performance liquid chromatography with electrospray ionization and tandem mass spectrometry. 1,6-Bis(methanesulfonyloxy)hexane, a synthesized analogue of busulfan, was used as the internal standard (IS). The acquisition was performed in the multiple reaction monitoring mode; busulfan and the IS were detected with no interferences from plasma matrix. The method was linear over the range 5-2500 ng mL(-1), with r2 > 0.99 and a run time of only 3.5 min. The intra- and inter-assay precisions were in the ranges 2.1-11.9% and 3.2-10.1%, respectively, and the intra- and inter-assay accuracies were 92.2-107.6% and 94.7-104.1%, respectively. The absolute recoveries were 82.0% (20 ng mL(-1)), 90.6% (1000 ng mL(-1)) and 80.0% (2000 ng mL(-1)) for busulfan, and 89.1% for the IS (1000 ng mL(-1)). The limits of detection and quantification were 2 and 5 ng mL(-1), respectively. The validated method was successfully applied to analyze plasma samples obtained from six adults receiving doses of 1 mg kg(-1) in a conditioning regimen prior to bone marrow transplantation. A marked intra-patient variation in busulfan concentrations during the steady state was observed, which limits the application of pharmacokinetic modeling and suggests that continuous therapeutic monitoring is necessary for adequate individualized dosing. In this regard, the present assay brings important advantages relative to other methods described in the literature, i.e., it is highly specific and simple to perform, with a rapid chromatographic run time (3.5 min), and the whole procedure can be completed in 4-5 h, which would permit dose corrections after the third dose allowing earlier and better dosing adjustments towards the target level of busulfan.     

Stereoselective conjugate addition of benzyl phenylsulfonyl carbanions to enoates derived from d-mannitol

The conjugate addition of benzylic phenylsulfonyl carbanions (2a'-d') to enoates derived from d-(+)-mannitol (E- or Z-1a-c) was studied using THF and THF/HMPA as solvent. Under kinetic conditions (-78 degrees C), enoate E-1a,b led to a mixture of syn-(R,S) and anti-(S,S) adducts (55/45), and syn-(R,S) adducts were the main product obtained ( approximately 90/10) from enoate Z-1a. Under thermodynamic conditions (-78 degrees C to room temperature) syn-(R,S) adducts were also preferentially formed ( approximately 90/10), despite the geometry at the double bond in the acceptor. Enoate 1c (E/Z = 57/43), bearing an additional benzyl group at the alpha-position, also reacted with carbanions 2'a,b, under thermodynamic conditions, leading to syn-adducts in excellent de (control at the three newly generated stereogenic centers). The adducts were quantitatively transformed into the corresponding beta-gamma-disubstituted gamma-butyrolactones and alpha,beta,gamma-trisubstituted gamma-butyrolactones. (1)H NMR studies (NOE and J-coupling) of these lactones allowed us to determine their configuration at the newly generated chiral centers. The reduction of the C-S bond in adducts syn-(R,S) with Na/Hg, followed by treatment of the resulting products in aqueous acid media, led to enantioenriched beta-benzyl-gamma-hydroxymethyl-gamma-butyrolactones. The conformational equilibrium of enoates E- and Z-1b was evaluated by theoretical calculations (ab initio, MP2/6-31G), and a mechanistic rationale was proposed to explain the observed stereoselectivities.     

Hydrolysis of new phthalimide-derived esters catalyzed by immobilized lipase

The last step of the production of four phthalimide-derived acids, designed to act as antiasthma drugs, was performed by enzymatic hydrolysis of the respective methyl or ethyl esters. The esters 4-ethyl-[2-(1,3-dioxo-1,3-dihydro-2-isoindoylyl)]-phenoxyacetic methyl ester (PHT-MET), 4-ethyl-[2-(1,3-dioxo-1,3-dihydro-2-isoindoylyl)]-phenoxyacetic ethyl ester, 4-(1,3-dioxo-1,3-dihydro-2-isoindoylyl)-phenoxyacetic ethyl ester, and 2-(1,3-dioxo-1, 3-dihydro-2-isoindoylyl)-phenoxyacetic ethyl ester were hydrolyzed by immobilized lipase. The enzymatic reaction could be used only to produce the desired 4-substituted compounds. The best result that was found to hydrolysis of PHT-MET, and, therefore, that ester was selected for optimization experiments in a three-phase system. Reactions were performed with solid biocatalyst (Lipozyme® RM IM), organic solvent phase (ethyl acetate), and aqueous phase (saturated Na₂CO₃ solution). To optimize the reaction conditions, an experimental design optimization procedure was used. The variables studied were the amount of enzyme, the temperature, and the volume of the aqueous solution. Time course experiments were then performed for different initial enzyme concentrations (0.5, 0.9, and 1.4 U_H/mL of solvent). The optimized reaction conditions found were 20 mg of Lipozyme (0.9 U_H/mL_solvent) and 5.0 mL of Na₂CO_3(sat) at 40°C for 6 h.     

Comprehensive two-dimensional liquid chromatography for the characterization of functional acrylate polymers

Comprehensive two-dimensional liquid chromatography-size-exclusion chromatography (LC x SEC) was investigated as a tool for the characterization of functional poly(methyl methacrylate) (PMMA) polymers. Ultraviolet-absorbance and evaporative light-scattering detection (ELSD) were used. A simple method to quantify ELSD data is presented. Each data point from the ELSD chromatogram can be converted into a mass concentration using experimental calibration curves. The qualitative and quantitative information obtained on two representative samples is used to demonstrate the applicability of LC x SEC for determining the mutually dependent molar-mass distributions (MMD) and functionality-type distributions (FTD) of functional polymers. The influence of the molar mass on the retention behavior in LC was investigated using LC x SEC for hydroxyl-functional PMMA polymers. The critical conditions, at which retention is--by definition--independent of molar mass, were not exactly the same for PMMA series with different end-groups. Our observations are in close agreement with theoretical curves reported in the literature. However, for practical applications of LC x SEC it is not strictly necessary to work at the exact critical solvent composition. Near-critical conditions are often sufficient to determine the mutually dependent distributions (MMD and FTD) of functional polymers.