Phase transformation of ZrO2 nanoparticles produced from zircon

This article focuses on the phase transformation of zirconia (ZrO₂) nanoparticles produced from zircon using a bottom-up approach. The influence of mechanical milling and thermal annealing on crystalline phase transformation of ZrO₂ nanoparticles was explored. It was found that the iron oxide, as an inherent impurity present in ZrO₂ nanoparticles, produced from zircon stabilises the cubic phase after calcination at 600°C. The stabilised cubic phase of ZrO₂ nanoparticles was disappeared and transformed into partial tetragonal and monoclinic phases after mechanical milling. The phase transformation occurred on account of the crystal defect induced by high-energy mechanical milling. The destabilisation of cubic phase into monoclinic phase was observed after the thermal annealing of ZrO₂ nanoparticles at 1000°C. The phase transitions observed are correlated to the exclusion of iron oxide from the zirconia crystal structure.     

Growth and luminescence properties of large‐scale zinc oxide nanotetrapods

Large‐scale zinc oxide (ZnO) nanotetrapods have been grown on p‐type Si (111) substrate by oxidizing zinc pieces in air by thermal evaporation technique without the presence of any catalyst. The size and morphology of the nanostructures was found to depend on experimental parameters. The grown nanostructures were characterized by X‐ray Diffraction (XRD), Photoluminescence (PL), Scanning Electron Microscopy (SEM), Transmission Electron Microscopy (TEM), High Resolution TEM (HRTEM) and analysis of elemental composition was done by Energy Dispersive X‐ray analysis (EDX). The EDX spectrum shows that the grown product contains Zn and O only. The X‐ray diffraction pattern indicates that the microstructure of the obtained products is typical hexagonal wurtzite ZnO. The optical properties were studied using room temperature PL spectroscopy which indicates that the products are of high optical quality and the near band edge UV transition peak intensity increases with decrease in tetrapod size. (© 2008 WILEY‐VCH Verlag GmbH & Co. KGaA, Weinheim)     

Acidic peroxo salts. A new class of initiators for vinyl polymerization. I. Kinetics of polymerization of acrylonitrile initiated by potassium monopersulfate catalyzed by Ag(I)

The kinetics of polymerization of acrylonitrile initiated by KHSO₅ and catalyzed by Ag(I) have been investigated in an aqueous medium over the temperature range of 35–50°C. The rates of polymerization R_p have been calculated and studied with respect to monomer and initiator. The catalytic activity of various metal ions on the initiator has been determined from a comparison of R_p values. The effects of monomer, catalyst, neutral salts, various amines, and inhibitor (hydroquinone) on the initial rate as well as maximum conversion have been studied. From the kinetics results a suitable reaction scheme has been proposed.     

Palladium-catalyzed oxamidation of alkenes: A new approach to benzoxazolidines

A novel palladium catalyzed protocol for the synthesis of benzoxazolidine by the reaction sulfamidophenol and terminal alkene was developed. This oxamidation process is simple and does not require any ligand, base or inert atmosphere for the overall transformation. From control experiments, it is apparent that the cross-coupling reaction proceeds with initial formation of enesulfonamide which undergoes nucleopalladation by the intramolecular annulation and subsequent protodepalladation by TsOH to afford the benzoxazolidine.     

Characterization of non-polar aromatic hydrocarbons in crude oil using atmospheric pressure laser ionization and Fourier transform ion cyclotron resonance mass spectrometry (APLI FT-ICR MS)

We report on the successful application of the recently introduced atmospheric pressure laser ionization (APLI) method as a novel tool for the analysis of crude oil and its components. Using Fourier transform ion cyclotron resonance mass spectrometry, unambiguous determination of key compounds in this complex matrix with unprecedented sensitivity is presented.     

Validation of primary formaldehyde gas standards prepared by dynamic thermogravimetry through a tri-national comparison of gaseous formaldehyde amount fraction

A validation study for primary formaldehyde gas standards was performed at three National Metrology Institutes: the Korea Research Institute of Standards and Science (KRISS), the National Metrology Institute of Japan (NMIJ) and the National Institute of Metrology of China (NIM). The studied materials had a nominal amount fraction of 2 μmol/mol formaldehyde in nitrogen balance and were prepared in 10-L aluminum cylinders by KRISS. The impurities in the materials were analyzed using a gas chromatograph/atomic emission detector and a Fourier-transform infrared spectrometer (FTIR). The stability of the materials was assessed for 1 year by KRISS using paraformaldehyde as a source for the primary standard gas and a cavity ring-down spectrometer (CRDS) instrument as the measurement method. The amount fraction of formaldehyde in the materials decreased linearly by 0.74 % each month. The studied materials that exhibited similar linear rates of decline were distributed to the participants. After the measurement was completed by the participants, the materials were returned to KRISS and the stability analysis based on the primary standard maintained at KRISS was repeated. NMIJ analyzed the materials using paraformaldehyde as the source of the primary standard of formaldehyde and FTIR analysis, whereas NIM used trioxane as the primary standard gas source and CRDS analysis. The results of the comparison revealed good agreement between the results and were within the expanded uncertainty of 2 % although each of them used different combinations of methods in the generation of primary gas standards and measurements.     

Physicochemical studies on the micellization behavior of cetylpyridinium chloride and triton X-100 binary mixtures in aqueous medium

Physicochemistry of micellization of binary mixtures of cetylpyridinium chloride (CPC) and Triton X-100 (TX-100) have been investigated and the data collected have been analyzed and correlated. Tensiometric, conductometric, spectrophotometric, calorimetric and polarographic methods have been employed in the study. Parameters like critical micellar concentration (CMC), counter-ion binding, energetics of micellization, interfacial surfactant adsorption and minimum area of amphiphile head groups at CMC have been determined. The diffusion coefficients of pure and mixed micelles in solution have been determined by the polarographic method. The regular solution theory of Rubingh has been considered to get information on the micellar composition and their mutual interaction (synergistic for the studied system) in solution. The packing of the monomer in micelle has been estimated to witness spherical geometry for CPC and its mixtures with TX-100, whereas the later has been found to be spheroidal. Polarographic measurements have evidenced comparable diffusion coefficients of CPC and TX-100 micelles whereas their mixed micelles have shown lower values with a minimum, at equimolar composition.     

An EOQ model for perishable products with discounted selling price and stock dependent demand

A single item economic order quantity model is considered in which the demand is stock dependent. After a certain time the product starts to deteriorate and due to visualization effect and other aspects of deterioration the demand becomes constant. In that situation a discount on selling price provides significant increment in demand rate. In this paper we investigate how much discount on selling price may be given during deterioration to maximize the profit per unit time and whether a pre-deterioration discount affects the unit profit or not. A mathematical model is developed incorporating both pre- and post deterioration discounts on unit selling price, where analytical results reveal some important characteristics of discount structure. A numerical example is presented and sensitivity analysis of the model is carried out.     

One pot glucose detection by [Fe(III)(biuret-amide)] immobilized on mesoporous silica nanoparticles: an efficient HRP mimic

An [Fe(III)(biuret-amide)] complex has been immobilized onto mesoporous silica nanoparticles via Cu(I) catalyzed azide-alkyne click chemistry. This hybrid material functions as an efficient peroxidase mimic and was successfully used for the quantitative determination of hydrogen peroxide and glucose via a one-pot colorimetric assay.