图像的自动采集分析和实现

文章针对焊件检测过程中需大量采集和分析实时图像的要求 ,利用小波分析的特点 ,相关跟踪识别视频图像运动状态 ,实现自动采集、分析处理和储存一并完成 ,解决了视频图像连续捕获不能得到高像质的问题。     

C-V法提取SiC隐埋沟道MOSFET沟道载流子浓度

本文对用C-V法提取SiC隐埋沟道MOSFET沟道载流子浓度的方法进行了理论和实验分析. pn结的存在所造成的埋沟MOS结构C-V曲线的畸变为沟道载流子浓度的提取带来一些问题. SiC/SiO₂界面上界面态的存在也会使提取出的数值与实际数值产生偏差. 本文首先从理论上分别分析了沟道深度和界面态对沟道载流子浓度提取结果的影响，然后对两种沟道深度的埋沟MOS结构C-V曲线进行了测试，提取出了沟道掺杂浓度. 在测试中，采用不同的扫描速率，分析了界面态对提取结果的影响. 理论分析结果和实验测 关键词： C-V法 SiC 隐埋沟道MOSFET 沟道载流子浓度     

测量冷原子温度的理论与近似拟合公式的误差分析

对短程飞行时间法(tim e-of-flight,TOF)中推算冷原子温度的理论拟合公式与近似拟合公式进行了误差分析与比较。研究表明:对于使用短程飞行吸收光谱信号推测冷原子团温度,当探测光光斑半径与冷原子团高斯半径之比k小于0.2时,理论拟合公式和近似拟合公式能很好的相符,随着探测光光斑半径与冷原子团高斯半径比值的逐渐增大,用近似拟合公式所得TOF吸收信号与用理论拟合公式所得TOF吸收信号的误差也将逐渐增大,当比值为0.5时,用近似拟合公式所得TOF吸收信号的误差将增大到20%。     

A Convenient Synthetic Method of Metal Dendritic Porphyrins

Metal porphyrins are natural antioxidant reagent1-3. However, due to the characteristics of structures, they are only soluble in inorganic acids and part of polar organic solvents. Thus, it is limited to be used as effective pharmaceutical preparations. T…     

二维非正交坐标斜方格金属光子带隙结构

金属光子带隙结构在高能加速器、微波真空电子器件和太赫兹波源等方面具有重要的应用前景.基于实空间传输矩阵理论，详细研究了非正交坐标系下二维斜方格金属光子带隙结构，给出了计算横电模、横磁模完全带隙结构的一般公式，并分析了填充系数、任意斜角及金属柱横截面对带隙结构的影响.计算结果在退化为正方格情况下时，与其他方法的计算结果取得很好的一致. 关键词： 光子晶体 金属光子带隙 传输矩阵法 微波真空电子器件     

AnUV-algorithm for semi-infinite multiobjective programming

In this paper, we give an application ofUV-decomposition method of convex programming to multiobjective programming, and offer a new algorithm for solving semi-infinite multiobjective programming. Finally, the superlinear convergence of the algorithm is proved.     

考虑材料熔化潜热的高温高压本构

本文在修正的SCG模型基础上，提出了一种考虑了熔化潜热的高温高压本构.该本构所给出的铝的剪切模量的变化分为三个阶段：加工硬化，温度软化和熔化，并在完全熔化点处变为零.并且在前两个阶段，计算的结果与修正的SCG模型所给出的剪切模量的差别不超过4%，这一差别是在动高压实验误差范围之内的，在熔化区所给出的剪切模量与现有的实验数据相符合. 关键词： 剪切模量 熔化潜热 修正的SCG模型 动高压实验     

Simulation of a turbulent premixed open V-shaped flame using contour advection with surgery

Despite its capability of high spatial resolution, simulation of turbulent flows with traditional Lagrangian (front tracking) scheme is often discouraged by numerical instability caused by clustering of marker nodes and topological changes of fronts. Contour advection surgery (CAS), being a robust front tracking scheme, can limit the growth of front complexity during simulation without jeopardizing accuracy or efficiency. This allows it to open up an advantage over traditional front-tracking schemes. It has already been demonstrated that CAS, with incorporation of the reaction sheet model, can accurately simulate the propagation and advection of a turbulent premixed V-shaped flame. In this study, it is further tested with 10 values of vortex circulation. A range of upstream turbulence levels of 1.8–19.8% was obtained. Results indicate that upstream turbulence increase the average flame length, flame zone area and the overall burning rate. Flame surface density Σ was also estimated. Maximum values of Σ obtained lie in the range 0.1–1.4 mm⁻¹. Skewness towards the burnt region was observed in all profiles of Σ. Similar to results from laboratory experiments, it was found that Σ values decreases with upstream turbulence. From this study, the ability of CAS to cope with intense turbulence is demonstrated and a better quantitative understanding on the scheme has also been acquired.