Emulsifier-free emulsion polymerization of tetrafluoroethylene by radiation. I. Effects of reaction conditions on the polymerization rate and polymer molecular weight

The radiation-induced emulsifier-free emulsion polymerization of tetrafluoroethylene was carried out at an initial pressure of 2–25 kg/cm², temperature of 30–110°C, and under a dose rate of 0.57 × 10⁴?3.0 × 10⁴ rad/hr. The rate of polymerization was shown to be proportional to 1.0 and 1.3 powers of the dose rate and initial pressure, respectively, and is maximal at about 70°C. The molecular weight of polytetrafluoroethylene (PTFE) lies in the range of 10⁵?10⁶, increases with reaction time in the early stage of polymerization, and is maximal at 70°C but is almost independent of the dose rate. An interesting discovery is that PTFE, a hydrophobic polymer, forms as a stable latex in the absence of emulsifier. When PTFE latex coagulates during polymerization under certain conditions, the polymerization rate decreases, probably because polymerization proceeds mainly on the polymer particle surface. The observed rate acceleration and successive increase in polymer molecular weight may be due to slow termination of propagating radicals in the rigid PTFE particles.     

Photo-induced dimerization of 1-naphthoxide anion: Electron transfer mechanism

Irradiation of sodium 1-naphthoxide in MeOH gave selectively 1,4-dihydro-4',8-dihydroxy-1,1'-binaphthyl 2. A similar reaction in PhH afforded the regioisomer 5, along with 6, Structural proof is presented for these hitherto unknown dimers. The reaction is completely quenched in the presence of naphthalene, a good electron scavenger. This new type of photodimerization was proved to be initiated by intermolecular electron-transfer from the excited 1-naphthoxide anion to the ground state one to give the oxidation-reduction dimers.     

Effect of dose rate on the radiation-induced polymerization of ethylene in tert-butyl alcohol

The dependence of the dose rate on the rate of radiation-induced polymerization of ethylene in tert-butyl alcohol containing 5 vol-% water was studied. The reaction was carried out by use of a reactor with a capacity of 100 ml under the following conditions: pressure, 200 kg/cm²; temperature, 24 ± 3°C; dose rate, 3.7 × 10⁴?1.6 × 10⁵ rad/hr; amount of medium, 70 ml. The dose rate exponents for rate of the polymerization, the molecular weight, and the number of polymer chain were found to be about 0.8, ?0.1, and 0.9, respectively. These results were well explained with kinetic results (obtained by a novel analytical method) for the polymerization which contain both first-order and second-order terminations for the concentrations of propagating radical. The individual values of the rate constants in each elementary reaction were also obtained.     

Optimization of the electrokinetic supercharging preconcentration for high-sensitivity microchip gel electrophoresis on a cross-geometry microchip

We developed a novel on-line preconcentration procedure for microchip gel electrophoresis (MCGE), which enables application of electrokinetic supercharging (EKS) for highly sensitive detection of DNA fragments on a cross-geometry microchip. In comparison with conventional pinched injection using the cross microchip, the present approach allows loading a much larger amount of the sample by taking advantage of a newly developed operational mode. In order to obtain high preconcentration effect and prevent splitting of an enriched sample into subchannels, i.e., off the detector range, effects of the voltage applied on the reservoirs and the time of isotachophoretic preconcentration were examined. The optimal balance between the voltage and time was found for a high-sensitivity analysis of DNA fragments. After experimental optimization the detection limit of a 150 bp fragment was as low as 0.22 mg/L (S/N = 3) that is 10 times better than using the conventional pinched injection.     

Increase in the Intracellular Bulk Water Content in the Early Phase of Cell Death of Keratinocytes,Corneoptosis, as Revealed by 65 GHz Near-Field CMOS Dielectric Sensor

While bulk water and hydration water coexist in cells to support the expression of biological macromolecules, how the dynamics of water molecules, which have long been only a minor role in molecular biology research, relate to changes in cellular states such as cell death has hardly been explored so far due to the lack of evaluation techniques. In this study, we developed a high-precision measurement system that can discriminate bulk water content changes of ±0.02% (0.2 mg/cm³) with single-cell-level spatial resolution based on a near-field CMOS dielectric sensor operating at 65 GHz. We applied this system to evaluate the temporal changes in the bulk water content during the cell death process of keratinocytes, called corneoptosis, using isolated SG1 (first layer of stratum granulosum) cells in vitro. A significant irreversible increase in the bulk water content was observed approximately 1 h before membrane disruption during corneoptosis, which starts with cytoplasmic high Ca²⁺ signal. These findings suggest that the calcium flux may have a role in triggering the increase in the bulk water content in SG1 cells. Thus, our near-field CMOS dielectric sensor provides a valuable tool to dissect the involvement of water molecules in the various events that occur in the cell.     

Charge transport study on single crystals of β-LiAl

Charge transport properties of β-LiAl were studied in the composition range of 48.0–50.2 at.% Li. Measurements were made on single crystal samples and down to the liquid He temperature. The resistivity changes linearly with temperature above 125 K, with a thermal coefficient of 72–95nΩ cm K^?1. The Matthiessen law was obeyed very well. A component dependent on temperature, which was described by the Grüneisen formula, is insensitive to a change of the chemical composition. On the other hand, the residual resistivity depends largely on the composition and contributes up to 58% of the total resistivity in Li_0.498. It is chiefly due to the substituted Li atoms on the Al sublattice.     

Hyers–Ulam stability of linear differential operator with constant coefficients

Let P(z) be a polynomial of degree n with complex coefficients and consider the n–th order linear differential operator P(D). We show that the equation P(D)f = 0 has the Hyers–Ulam stability, if and only if the equation P(z) = 0 has no pure imaginary solution. (© 2003 WILEY‐VCH Verlag GmbH & Co. KGaA, Weinheim)     

Observations of surface modifications induced by the multiple pulse irradiation using a soft picosecond x-ray laser beam

To study the interactions between picosecond soft x-ray laser (SXRL) beams and material surfaces, gold (Au), copper (Cu), and silicon (Si) surfaces were irradiated with SXRL pulses having a wavelength of 13.9 nm and a duration of ～7 ps. Following irradiation, the surfaces of the substrates were observed using a scanning electron microscope and an atomic force microscope. With single pulse irradiation, ripple-like structures were formed on the Au and Cu surfaces. These structures were different from previously investigated conical structures formed on an Al surface. In addition, it was confirmed that the development of modified structures, i.e., growth of hillocks on the Au and Cu surfaces, was observed after multiple SXRL pulse exposures. However, on the Si surface, deep holes that seemed to be melted structures induced by the accumulation of multiple pulses of irradiations were found. Therefore, it was concluded that SXRL beam irradiation of various material surfaces causes different types of surface modifications, and the changes in the surface behaviors are attributed to the differences in the elemental properties, such as the attenuation length of x-ray photons.     

Achievement of a 920-MHz high resolution NMR

We have developed a 920-MHz NMR system and performed the proton NMR measurement of H(2)O and ethylbenzene using the superconducting magnet operating at 21.6 T (920 MHz for proton), which is the highest field produced by a superconducting NMR magnet in the persistent mode. From the NMR measurements, it is verified that both homogeneity and stability of the magnet have a specification sufficient for a high resolution NMR.