Design and Experimental Characterization of Low‐Volume PM10/2.5/1.0 Trichotomous Sampler Inlet

This paper presents the development and laboratory evaluation of a PM10/2.5/1.0 trichotomous sampling inlet that consists of two main parts: a previously designed PM10 size‐selective inlet part and a PM2.5/1.0 two‐stage virtual impactor, which was newly fabricated and attached serially to the PM10 size selective inlet part. Particles are collected in three locations through the trichotomous sampling inlet to provide for not only particle concentration measurements of PM10, PM2.5 and PM1.0, but also those of PM2.5–10 and PM1.0–2.5.     

Assessment of thermal expansion coefficient of methylsilsesquioxane thin film

For the methylsilsesquioxane film whose optical birefringence is almost zero, it was recently reported that its vertical thermal expansion coefficient (CTE) was approximately one order of magnitude larger than the lateral CTE. Though the birefringence is not an absolute predictor of anisotropic behavior, the discrepancy in both the CTEs was so remarkable that it was essential to investigate whether the anisotropy was intrinsic property or not. If the effect of Poisson's ratio is considered in the calculation of the vertical CTE and when elastic modulus measured by surface acoustic wave spectroscopy is used in the assessment of the lateral CTE, both the CTEs are coincident with each other. Therefore, it can be concluded that the discrepancy in the CTEs can be attributed to a higher in‐plane polymer chain orientation but it can also arise from the misleadingly assumed modulus and Poisson's ratio. © 2006 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 44: 3109–3120, 2006     

Numerical simulation on an interaction of a vortex street with an elliptical leading edge using an unstructured grid

An algorithm for a time accurate incompressible Navier–Stokes solver on an unstructured grid is presented. The algorithm uses a second order, three‐point, backward difference formula for the physical time marching. For each time step, a divergence free flow field is obtained based on an artificial compressibility method. An implicit method with a local time step is used to accelerate the convergence for the pseudotime iteration. To validate the code, an unsteady laminar flow over a circular cylinder at a Reynolds number of 200 is calculated. The results are compared with available experimental and numerical data and good agreements are achieved. Using the developed unsteady code, an interaction of a Karman vortex street with an elliptical leading edge is simulated. The incident Karman vortex street is generated by a circular cylinder located upstream. A clustering to the path of the vortices is achieved easily due to flexibility of an unstructured grid. Details of the interaction mechanism are analysed by investigating evolutions of vortices. Characteristics of the interactions are compared for large‐ and small‐scale vortex streets. Different patterns of the interaction are observed for those two vortex streets and the observation is in agreement with experiment. Copyright © 2004 John Wiley & Sons, Ltd.     

Synthesis and characterization of novel polyimides with 2,2‐bis[4(4‐aminophenoxy)phenyl]phthalein‐3′,5′‐bis(trifluoromethyl)anilide

2,2‐Bis[4(4‐aminophenoxy)phenyl]phthalein‐3′,5′‐bis(trifluoromethyl)anilide (6FADAP), containing fluorine and phthalimide moieties, was synthesized via the Williamson ether condensation reaction from 1‐chloro‐4‐nitrobenzene and phenolphthalein‐3′,5′‐bis(trifluoromethyl)anilide, which was followed by hydrogenation. Monomers such as 2,2‐bis[4(4‐aminophenoxy)phenyl]phthalein‐anilide containing phthalimide groups and 2,2‐bis[4(4‐aminophenoxy)phenyl]phthalein containing only phthalein moieties were also synthesized for comparison. The monomers were first characterized by Fourier transform infrared (FTIR), ¹H NMR, ¹⁹F NMR, elemental analysis, and titration and were then used to prepare polyimides with 2,2‐bis(3,4‐dicarboxyphenyl)hexafluoropropane dianhydride. The polyimides were designed to have molecular weights of 20,000 g/mol via off‐stoichiometry and were characterized by FTIR, NMR, gel permeation chromatography (GPC), differential scanning calorimetry, and thermogravimetric analysis. Their solubility, water absorption, dielectric constant, and refractive index were also evaluated. The polyimides prepared with 6FADAP, containing fluorine and phthalimide moieties, had excellent solubility in N‐methylpyrrolidinone, N,N‐dimethylacetamide, tetrahydrofuran, CHCl₃, tetrachloroethane, and acetone, and GPC analysis showed a molecular weight of 18,700 g/mol. The polyimides also exhibited a high glass‐transition temperature (290 °C), good thermal stability (～500 °C in air), low water absorption (1.9 wt %), a low dielectric constant (2.81), a low refractive index, and low birefringence (0.0041). © 2003 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 41: 3361–3374, 2003     

A new VOF‐based numerical scheme for the simulation of fluid flow with free surface. Part II: application to the cavity filling and sloshing problems

Finite element analysis of fluid flow with moving free surface has been performed in 2‐D and 3‐D. The new VOF‐based numerical algorithm that has been proposed by the present authors (Int. J. Numer. Meth. Fluids, submitted) was applied to several 2‐D and 3‐D free surface flow problems. The proposed free surface tracking scheme is based on two numerical tools; the orientation vector to represent the free surface orientation in each cell and the baby‐cell to determine the fluid volume flux at each cell boundary. The proposed numerical algorithm has been applied to 2‐D and 3‐D cavity filling and sloshing problems in order to demonstrate the versatility and effectiveness of the scheme. The proposed numerical algorithm resolved successfully the free surfaces interacting with each other. The simulated results demonstrated applicability of the proposed numerical algorithm to the practical problems of large free surface motion. It has been also demonstrated that the proposed free surface tracking scheme can be easily implemented in any irregular non‐uniform grid systems and can be extended to 3‐D free surface flow problems without additional efforts. Copyright © 2003 John Wiley & Sons, Ltd.     

Pd (II)‐catalyzed vinyl addition polymerization of novel functionalized norbornene bearing dimethyl carboxylate groups

Three novel functionalized polynorbornenes (PNB) with pendant dimethyl carboxylate group (carboxylates—acetate, propionate, and butyrate) are synthesized as a vinyl‐type with a palladium (II) catalyst in high yield. The effects of size of substitutents, molar ratio of monomer to catalyst, solvent polarity, reaction time, and temperature on the polymerization of exo‐norbornene dimethyl propionate were systematically investigated. The low molar ratio and temperature, as well as high polarity of solvent, and long reaction time, are favorable for the enhancement of the monomer conversion, especially, the solvent have an obvious effect on the catalyst activity. The resulting poly(cis‐norbornene‐exo‐2,3‐dimethyl carboxylates) (PNB‐dimethyl carboxylates) show good solubility in common organic solvent and high thermal stability up to 360 °C. The glass transition temperature was detected by DMA at 331, 324, and 318 °C for acetate, propionate, and butyrate, respectively. © 2007 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 45: 3391–3399, 2007     

In‐line monitoring of UV photopolymerization with a quartz crystal resonator

An in‐line monitoring device using a quartz crystal resonator for thin film polymerization was proposed, and its performance has been evaluated by implementing in the UV polymerization of 2‐hydroxyethyl methacrylate with a photoinitiator of 1‐chloroanthraquinone. Because the variation of resonant resistance of the resonator is proportional to the square root of viscosity change that is closely related to the polymerization degree, the resistance can be used as a measure of the polymerization degree. The resistance measurements were compared with the outcome of instrumental analyses of polymerization degree using an FTIR spectrometer and a gel permeation chromatograph. The experimental results showed that the resistance measurements were consistent with the experimental outcome of the instrumental analyses, and this indicates the effectiveness of the proposed device. Owing to the simplicity and availability of the resonator system, its wide utilization in the monitoring of a variety of film polymerization processes, including photoresistor application, is expected. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 2428–2439, 2006     

Synthesis and characterization of novel perfluorinated polyimides with 3D‐controlled structures for photonic applications

We have designed and synthesized novel perfluorinated polyimides with 3D controlled structure. At first, we successfully developed the new synthetic routes to diamines with pendant bulky perfluorinated aromatic units in a multi‐step synthetic procedure. Novel perfluorinated polyimides were prepared in a two‐step reaction in N‐methyl‐2‐pyrrolidinone (NMP) solution: The first step was for the synthesis of polyamic acids (PAAs) and the second reaction was for the imidization of PAA. The polymer yield was over 89% and the inherent viscosity of PAAs was in the range of 0.24–0.36 dL/g. The thin films were prepared by spin‐coating the PAA solution in NMP onto various substrates such as a Si wafer or a KBr pellet, dried at 80 °C and further cured at 230 °C. The resultant polyimides are thermally stable over 400 °C. The refractive index and birefringence of the resultant polyimides are 1.5858–1.6452 and 0.01–0.005, respectively. The refractive index of polyimide decreases with increasing the fluorine content. The copolymerization and the ether linkages into the backbone reduce the birefringence of polyimides. Surprisingly, the pendant ether linkage is not a crucial factor in reducing the polyimide birefringence. Their birefringence is comparatively very low, compared with that of previous polyimides. © 2005 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 1326–1342, 2006     

Synthesis and luminescence characteristics of conjugated dendrimers with 2,4,6‐triaryl‐1,3,5‐triazine periphery

We have synthesized conjugated dendrimer with triazine peripheries, and their luminescence properties were investigated. The dendrimers consist of dendritic triazine wedges for electron transport, distyrylbenzene core as an emitting moiety, and t‐butyl peripheral groups for good processing properties. The dendrimers have LUMO values of about ?2.7 eV possibly because of the triazine moiety with high electron affinity. Photoluminescence study indicates that energy transfer occurs from the triazine wedges to the stilbene bridge, and finally to the core chromophore units due to a cascade decrease of bandgap from the peripheral wedge to core moiety. Therefore, the emission wavelength was determined by the structure of the core unit. The energy transfer efficiency of distyrylbenzene‐cored dendrimers was about 75 and 55% for Trz‐1GD‐DSB and Trz‐2GD‐DSB, respectively. A preliminary electroluminescence property also was investigated. © 2005 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 254–263, 2006     

Synthesis and cationic photopolymerization of new fluorinated,polyfunctional propenyl ether oligomers

New fluorinated, polyfunctional propenyl ether functionalized resins were synthesized, and their behavior in cationic photopolymerization was investigated. The photopolymerization proceeded efficiently with a high double‐bond conversion (>90%), giving rise to UV‐cured coatings characterized by low glass‐transition temperatures (?33 °C ≤ glass‐transition temperature ≤ ?15 °C) and hydrophobic surface properties. A fluorinated additive was also employed as a reactive additive in the cationic photopolymerization of trimethylolpropane tripropenyl ether, increasing the double‐bond conversion, polymer network flexibility, thermal stability, and surface hydrophobicity. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 6943–6951, 2006