A new synthesis of angulary substituted octalins via an anionic oxy-cope rearrangement

The divinyl carbinols $\text{3a}$ and $\text{3b}$ furnished octalinols $\text{4a}$ and $\text{4b}$ respectively on treatment with base.     

Roles of surface Te, Nb, and Sb oxides in propane oxidation to acrylic acid over bulk orthorhombic Mo-V-O phase

The outermost surfaces and subsurface layers of the orthorhombic (M1) Mo-V-O catalysts promoted with Te, Nb, and Sb oxide species at submonolayer surface coverage were examined by low-energy ion scattering (LEIS). This study indicated that the Nb oxide species was preferentially located at the topmost surface, while the subsurface Te and Sb concentrations declined gradually into the bulk. Although the original Mo-V-O catalyst was essentially unselective in propane oxidation to acrylic acid, significant improvement in the selectivity to acrylic acid was observed when Te, Nb, and Sb oxides were present as the surface species at submonolayer coverage. These findings further suggested that the formation of the surface V-O-M bonds (M = Nb, Te, or Sb) was highly beneficial for both the activity and selectivity of the orthorhombic Mo-V-O catalysts in propane oxidation to acrylic acid. The highest selectivity was observed when both Nb and Te (or Sb) oxide species were present at the surface. The selectivity trends established for the surface-promoted Mo-V-O catalyst parallel those found previously for the corresponding bulk Mo-V-M-O catalysts. These results further indicated that the introduction of surface metal oxide species is a highly promising method to prepare well-defined model catalysts for studies of the structure-activity/selectivity relationships as well as optimize the catalytic performance of the bulk mixed Mo-V-M-O catalysts for selective (amm)oxidation of propane.     

Use of N-trifluoroacetyl-protected amino acid chlorides in peptide coupling reactions with virtually complete preservation of stereochemistry

The use of protected amino acid chlorides for peptide coupling reactions has long been avoided due to the extensive racemization that commonly occurs during either the acid chloride formation or the coupling reaction itself. Conditions are described which allow N-trifluoroacetyl-protected amino acid chlorides to be generated in high purity and with high retention of stereochemical integrity. Control of temperature is the predominant factor in controlling racemization, and rapid formation of acid chlorides under low temperature can be conveniently achieved using Vilsmeier reagent. Stereochemical integrity is further maintained when coupling of N-trifluoroacetyl acid chlorides is carried out with amino acid esters under Schotten-Baumann conditions using specific controls on pH, temperature, and agitation. Second order rate constants for coupling and the azlactone formation associated with racemization were measured to be 4260 and 3.6 L/mol s, respectively. This high rate differential allows for the reaction to be run with a minimum excess of amine ester, and makes it suitable for continuous processing. The applicability of the preferred coupling conditions to a range of amino acid couplings is described.     

Spectral characteristics of 2-aminodiphenylamine in different solvents and at various pH values.

The absorption and fluorescence spectra of 2-aminodiphenylamine (2ADA) have been studied as a function of solvent polarity and acid concentration. Analysis of solvatochromic and prototropic shifts of 2ADA reveals: (i) the presence of intramolecular hydrogen bonding between imino and amino groups in the ground state, (ii) dual fluorescence (360 and 430 nm) of the monocation (2ADA+) formed by the protonation of amino group; and (iii) proton-induced quenching of the monocation (2ADA+) fluorescence. In the dual fluorescence of 2ADA+, the longer wavelength emission at 430 nm is found to be from the twisted form of the monocation. The rate constants of the proton-induced quenching of 2ADA+ are determined.     

Biosorption of Copper and Cadmium in Packed Bed Columns with Live Immobilized Fungal Biomass of <Emphasis Type="Italic">Phanerochaete chrysosporium</Emphasis>

Biosorption of copper (II) and cadmium (II) by live Phanerochaete chrysosporium immobilized by growing onto polyurethane foam material in individual packed bed columns over two successive cycles of sorption–desorption were investigated in this study. Initial pH and concentrations of the metals in their respective solutions were set optimum to each of those: 4.6 and 35 mg·l⁻¹ in case of copper and 5.3 and 11 mg·l⁻¹ for cadmium. The breakthrough curves obtained for the two metals during sorption in both the cycles exhibited a constant pattern at various bed depths in the columns. The maximum yield of the columns in removing these metals were found to be, respectively, 57% and 43% for copper and cadmium indicating that copper biosorption by the immobilized fungus in its column was better than for cadmium. Recovery values of the sorbed copper and cadmium metals from the respective loaded columns by using 0.1 N HCl as eluant was observed to be quite high at more than 65% and 75%, respectively, at the end of desorption in both the cycles. Breakthrough models of bed-depth service time, Adams–Bohart, Wolborska, and Clark were fitted to the experimental data on sorption of copper and cadmium in the columns, and only the Clark model could fit the sorption performance of the columns well over the entire range of ratios of concentrations of effluent to influent, i.e., C/C ₀ for both copper and cadmium biosorption. The kinetic coefficients of mass transfer and other suitable parameters in the system were determined by applying the experimental data at C/C ₀ ratios lower than 0.5 to the other three models.     

On the condensation of phenyl ethynyl ketone with cyclopentadiene—a reinvestigation

The earlier structural assignment as 1 for the product obtained by the condensation of phenyl ethynyl ketone with cyclopentadiene is now revised to the dimeric structure 5d.     

A model for the phonon frequency distribution function for crystalline polyethylene

A model for the phonon frequency distribution function of crystalline polyethylene has been developed considering the mass of the vibrating unit to be two methylene groups and distinguishing between the ‘hard’ longitudinal and transverse dispersive modes. It explains the temperature variation of specific heat of polyethylene and can be used for other studies.     

Bubbles pinned on electrodes: Friends or foes of aqueous electrochemistry?

Electrochemists and engineers regard adherent gas bubbles as redox-inactive and therefore blocking entities. Adhesion of bubbles at electrodes generally carries an energy penalty. But this is not always the case: bubbles pinned on an electrode surface initiate the oxidation of water-soluble species under conditions where such reactions would normally be considered impossible. Here we critically review the recent literature that is beginning to unveil the novel concept of on-water electrochemistry. Harnessing electrochemical reactivity of the water–gas–electrode interface has the potential to become a game-changer in organic electrosynthesis, accelerating the transition toward a sustainable chemical industry by simplifying the direct integration of renewable electricity into the production of commodity chemicals.     

Development of nano-catalyzed membrane for PEM fuel cell applications

Nano-catalyzed membrane with different platinum (Pt) catalyst loadings (0.25 to 1 mg cm^?2) was investigated for proton exchange membrane fuel cell applications, and the Pt loading on the Nafion membrane was prepared by non-equilibrium impregnation reduction method. The prepared catalyzed membranes were subjected to various characterisations, namely, X-ray diffraction, high-resolution scanning electron microscopy (HRSEM) with energy-dispersive X-ray, cyclic voltammetry, polarisation and electrochemical impedance spectroscopy. The polycrystalline fcc cubic structure and the particle size of Pt catalyst were estimated by X-ray diffraction analysis. The membrane with 0.4 mg cm^?2 of Pt loading exhibits a favourable surface morphology which is confirmed by HRSEM image. Electrochemical investigations were clearly evident that the uniform distributions of Pt particles with fine pores on Nafion membrane facilitated the three-phase boundary which leads to a better cell performance. Electrochemical impedance spectroscopy demonstrated that the cell constructed using 0.4 mg cm^?2 of platinum-loaded membrane has lower resistance than the other Pt loading.