Surface redox induced bipolar switching of transition metal oxide films examined by scanning probe microscopy

The bipolar resistive switching mechanisms of a p-type NiO film and n-type TiO₂ film were examined using local probe-based measurements. Scanning probe-based current–voltage (I–V) sweeps and surface potential/current maps obtained after the application of dc bias suggested that resistive switching is caused mainly by the surface redox reactions involving oxygen ions at the tip/oxide interface. This explanation can be applied generally to both p-type and n-type conducting resistive switching films. The contribution of oxygen migration to resistive switching was also observed indirectly, but only in the cases where the tip was in (quasi-) Ohmic contact with the oxide.     

Ultrawidely tunable single-mode fiber acousto-optic filter

A single-mode fiber (SMF) acousto-optic tunable filter (AOTF) with a tuning range of more than 300 nm is demonstrated. The SMF used in the experiment has a ring of symmetric holes within the cladding, which causes a larger mode-index difference between the first and the second higher-order antisymmetric modes than those of a conventional SMF. As a result, the difference in beatlengths between the core mode and the higher-order modes is highly increased, which makes it possible for the SMF AOTF to exhibit a single resonance peak in the transmission spectrum over the wavelength range of 1.3-1.6 μm for given acoustic frequencies of 3.1-3.8 MHz.     

High performance Zn–Sn–O thin film transistors with Cu source/drain electrode

Zn–Sn–O (ZTO) thin film transistors (TFTs) were fabricated with a Cu source/drain electrode. Although a reasonably high mobility (μ_FE) of 13.2 cm²/Vs was obtained for the ZTO TFTs, the subthreshold gate swing (SS) and threshold voltage (V_th) of 1.1 V/decade and 9.1 V, respectively, were inferior. However, ZTO TFTs with Ta film inserted as a diffusion barrier, exhibited improved SS and V_th values of 0.48 V/decade and 3.0 V, respectively as well as a high μ_FE value of 18.7 cm²/Vs. The improvement in the Ta‐inserted device was attributed to the suppression of Cu lateral diffusion into the ZTO channel region. (© 2013 WILEY‐VCH Verlag GmbH & Co. KGaA, Weinheim)     

Biodegradable Holographic Polymer-Dispersed Liquid Crystal

The a-D-glucose was chemically modified with an allyl isocyanate (MG) and introduced into the polymer matrix for holographic polymer-dispersed liquid crystal (HPDLC), and the effects were studied in terms of morphology, grating formulation dynamics and electro-optical and biodegradable properties. Phase separation and diffraction efficiency increased at low content of (MG ≤ 4 wt%), while a rapid increase in crosslink density entrapped the LC droplets within the polymer to give poor phase separation, small droplet size, and low diffraction efficiency at high content. The HPDLC film was driven only with the addition of MG due to the increased droplet size with a minimum driving voltage of 18 V at 6.0 wt% MG. With the addition and an increasing amount of MG, the biodegradation of the composite film in a buffer solution was significantly increased in proportion to its amount.     

Properties of Graphene/Waterborne Polyurethane Nanocomposites Cast from Colloidal Dispersion Mixtures

Nanocomposites of waterborne polyurethane (WPU) reinforced with functionalized graphene sheets (FGSs) were effectively prepared by casting from a colloidal dispersion of FGS and WPU, and the morphology and physical properties were examined. The finer aqueous FGS dispersions or WPU with smaller particles yielded nanocomposites with enhanced electrical conductivity and thermal resistance due to finely dispersed FGS. The FGS nucleated the crystallization of the polycaprolactone (PCL) segments in WPU and improved its modulus. However, FGS inhibited crystal growth and deteriorated the tensile properties at high deformation, i.e., tensile strength and elongation at break, because the interaction between FGS and WPU hindered the chain rearrangement of WPU in the nanocomposite.     

Thermal and chemical nanofractal relaxation

We studied shape relaxation of nano-fractal islands, during annealing, after their growth from antimony cluster deposition on graphite surface. Annealing at 180^°C shows evidence of an increase of the fractal branch width with time followed by branch fragmentation, without changing the fractal dimension. The time evolution of the width of the arm suggests the surface self-diffusion mechanism as the main relaxation process. With Monte Carlo simulations, we confirmed the observed behavior. Comparison is done with our previous results on fragmentation of nano-fractal silver islands when impurity added to the incident cluster promotes rapid fragmentation by surface self-diffusion enhancement [1].     

Dimensional variation in production of high-aspect-ratio micro-pillars array by micro powder injection molding

Micro powder injection molding (μPIM) is one of the potential processes for the mass production of metallic microstructures and micro components. Here, μPIM is the miniaturization of conventional PIM, which involves four processing steps: mixing, injection molding, debinding and sintering. This paper looks into the feasibility and effectiveness of μPIM as a key mass production process for the fabrication of metallic micro components. For it to be an effective re-production process, it is imperative to examine how well parts can be duplicated/fabricated from a master mold. In this work, the dimensional variation of high-aspect-ratio micro-pillars arrays, in particular the dimensional shrinkage, global warpage, and surface roughness at each stage of the μPIM process for a range of molding pressures, are quantified and compared in detail. The sensitivity of the dimensional variation of the microstructures to the packing pressure is reported. The mechanism behind the dimensional variation is analyzed. PACS 81.20.Ev; 81.20.Hy; 81.70.Fy; 07.60.Ly; 81.05.-t