Determination of the boiling point distribution of sulfur compounds in light cycle oil using GC with a flame photometric detector and pyrolyzer

A method has been developed to determine the boiling point distribution of sulfur compounds in light cycle oils (LCO'S). The method chosen for this analysis was GC with a flame photometric detector (FPD) and pyrolyzer. Tests were carried out to evaluate the recovery efficiency, repeatability, and accuracy of the method. Repeatabilities within 2% were obtained. The recovery of benzothiophenes and dibenzothiophenes was close to 100%; this was important because these are the major sulfur components in LCO's. No hydrocarbon or solvent interferences were observed with the use of the pyrolyzer, even for a 95% solvent level. Comparison with results from other techniques showed that the method accurately determined the levels of sulfur compounds in the LCO boiling point range.     

Higher Fock Sectors in the Wick-Cutkosky Model

In the Wick-Cutkosky model we analyze nonperturbatively, in light-front dynamics, the contributions of two-body and higher Fock sectors to the total norm and electromagnetic form factor. It turns out that two- and three-body sectors always dominate. For a maximal value of the coupling constant α = 2π, corresponding to the zero bound-state mass M = 0, they contribute 90% to the norm. With decrease of α the two-body contribution increases up to 100%. The form factor asymptotic is always determined by a two-body sector.     

Intraspinal endodermal cyst: ultrastructural study of abnormal cilia.

Abnormal cilia were demonstrated in the lining epithelial cells of three cases of intraspinal endodermal (bronchogenic) cyst. The changes comprised a wide spectrum of ultrastructural abnormalities, including (a). cilia with abnormal axonemal microtubules, (b). swollen cilia, (c). compound cilia with or without excessive ciliary matrix, (d). naked cilia without limiting membrane, and (e). intracytoplasmic cilia and aggregates of microtubules. Of these, compound cilia and swollen cilia were most common. Cilia with dynein arm deficiency were not observed. Ciliary abnormalities found in the present study were very similar to those described in the bronchial epithelium of various diseases. The present findings suggest that the lining epithelium of intraspinal endodermal cyst shares similar ciliogenesis and susceptibility to abnormal ciliary formation as that of the bronchial epithelium.     

Support vector machine via nonlinear rescaling method

In this paper we construct the linear support vector machine (SVM) based on the nonlinear rescaling (NR) methodology (see [Polyak in Math Program 54:177–222, 1992; Polyak in Math Program Ser A 92:197–235, 2002; Polyak and Teboulle in Math Program 76:265–284, 1997] and references therein). The formulation of the linear SVM based on the NR method leads to an algorithm which reduces the number of support vectors without compromising the classification performance compared to the linear soft-margin SVM formulation. The NR algorithm computes both the primal and the dual approximation at each step. The dual variables associated with the given data-set provide important information about each data point and play the key role in selecting the set of support vectors. Experimental results on ten benchmark classification problems show that the NR formulation is feasible. The quality of discrimination, in most instances, is comparable to the linear soft-margin SVM while the number of support vectors in several instances were substantially reduced.     

Mössbauer Studies and Magnetic Properties of Y3−x Ce x Fe5O12

It is shown that in-situ ^166mHo (I = 7) in a spherical single crystal of HoF₃ can be used as sensitive internal thermometer to thermally detect NMR (NMR-TDNO) from the 100% abundant stable ¹⁶⁵Ho (I = 7/2) nuclei. In addition, new ^166mHo NMRON results are reported. Both the ^166mHo NMRON and ¹⁶⁵Ho NMR-TDNO spectra show three distinct quadrupolar split sub-resonances, in zero applied field. The data is used to make estimates of the Ho magnetic moments and quadrupole parameters for the ^166mHo and ^166mHo sites.     

Strong visible PL from the nc-Si thin film by Ni silicide mediated crystallization

We studied the growth of nanocrystalline silicon (nc-Si) thin film exhibiting a strong room temperature photoluminescence (PL) at 1.81–2.003 eV. The amorphous silicon was crystallized by Ni silicide mediated crystallization (Ni SMC) and then Secco-etched to exhibit the PL. The PL peak energy and intensity increase with increasing the metal density on the a-Si because of the reduction in the grain size down to 2 nm. The photoluminescence energy and peak intensity depend strongly on the Secco etch time because the grain size is reduced by etching the grain boundaries.     

Preparation,thermal properties,and flame retardance of epoxy–silica hybrid resins

A novel epoxy system was developed through the in situ curing of bisphenol A type epoxy and 4,4′‐diaminodiphenylmethane with the sol–gel reaction of a phosphorus‐containing trimethoxysilane (DOPO–GPTMS), which was prepared from the reaction of 9,10‐dihydro‐9‐oxa‐10‐phosphaphenanthrene‐10‐oxide (DOPO) with 3‐glycidoxypropyltrimethoxysilane (GPTMS). The preparation of DOPO–GPTMS was confirmed with Fourier transform infrared, ¹H and ³¹P NMR, and elemental analysis. The resulting organic–inorganic hybrid epoxy resins exhibited a high glass‐transition temperature (167 °C), good thermal stability over 320 °C, and a high limited oxygen index of 28.5. The synergism of phosphorus and silicon on flame retardance was observed. Moreover, the kinetics of the thermal oxidative degradation of the hybrid epoxy resins were studied. © 2003 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 41: 2354–2367, 2003     

Correlation between Al2O3 particles and interface of Al-Al2O3 coatings by cold spray

Al-Al₂O₃ composite coatings with different Al₂O₃ particle shapes were prepared on Si and Al substrate by cold spray. The powder compositions of metal (Al) and ceramic (Al₂O₃) having different sizes and agglomerations were varied into ratios of 10:1 wt% and 1:1 wt%. Al₂O₃ particles were successfully incorporated into the soft metal matrix of Al. It was found that crater formation between the coatings and substrate, which is typical characteristic signature of cold spray could be affected by initial starting Al₂O₃ particles. In addition, when the large hard particles of fused Al₂O₃ were employed, the deep and big craters were generated at the interface between coatings and hard substrates. In the case of pure soft metal coating such as Al on hard substrate, it is very hard to get proper adhesion due to lack of crater formation. Therefore, the composite coating would have certain advantages.     

Effects of physical aging on yielding kinetics of polycarbonate

The purpose of this work was to investigate the effects of physical aging on the kinetics of yielding in polycarbonate. PC samples were annealed over a wide range of aging times and temperatures. Both tensile and compressive tests were performed over various loading rates and temperatures to analyze the effects of aging time and aging temperature on yielding kinetics. Two grades of polycarbonate, Makrolon, of different molecular weights, PC-2608 (low M_w), and PC-3208 (high M_w), supplied by Bayer were analyzed. In unaged condition, PC is hard and tough, but after aging, it becomes more brittle. In terms of molecular movement, the yielding process is a thermally activated process involving inter- and intra-molecular motions. The time–temperature dependence of yielding behavior can be separated into two regions. Aging does not affect localized molecular motions of the β process during yielding. Physical aging in PC results in a slower jump rate of the main segments of macromolecules between two equilibrium positions. It reduces the flexibility of the macromolecules and thus, makes the polymer more brittle. Heat aging also causes a decrease of the entropy (ΔS) in polycarbonate, and this decrease is more important when the molecular weight is reduced. Increasing the annealing time and temperature results in a continuous reduction of ΔS. The rate of aging decreases with decreasing annealing temperature and below about 30 °C, no aging takes place. Annealing also strongly affects the excess of enthalpy in PC. However the effect of physical aging on yielding differs to that on enthalpy excess. The kinetics of yielding and aging processes in polycarbonate are also different. An increase in the strain rate does not have the same effect on the yield stress as an increase in the aging time by a same factor.     

A new VOF‐based numerical scheme for the simulation of fluid flow with free surface. Part II: application to the cavity filling and sloshing problems

Finite element analysis of fluid flow with moving free surface has been performed in 2‐D and 3‐D. The new VOF‐based numerical algorithm that has been proposed by the present authors (Int. J. Numer. Meth. Fluids, submitted) was applied to several 2‐D and 3‐D free surface flow problems. The proposed free surface tracking scheme is based on two numerical tools; the orientation vector to represent the free surface orientation in each cell and the baby‐cell to determine the fluid volume flux at each cell boundary. The proposed numerical algorithm has been applied to 2‐D and 3‐D cavity filling and sloshing problems in order to demonstrate the versatility and effectiveness of the scheme. The proposed numerical algorithm resolved successfully the free surfaces interacting with each other. The simulated results demonstrated applicability of the proposed numerical algorithm to the practical problems of large free surface motion. It has been also demonstrated that the proposed free surface tracking scheme can be easily implemented in any irregular non‐uniform grid systems and can be extended to 3‐D free surface flow problems without additional efforts. Copyright © 2003 John Wiley & Sons, Ltd.