Ductile–brittle transitions in the fracture of plastically deforming,adhesively bonded structures. Part II: Numerical studies

To enable the effective and reliable use of structural adhesive bonding in automotive applications, the cohesive properties of a joint need to be determined over a wide range of loading rates. In this paper, a strategy for determining these properties has been described and used to analyze a set of experimental results presented in a companion paper. In the particular system studied, a crack growing in a toughened quasi-static mode could make a catastrophic transition to a brittle mode of fracture. The cohesive parameters for both the toughened and brittle modes of crack growth were determined by comparing numerical predictions from cohesive-zone simulations to the results of experimental tests performed using double-cantilever beam specimens and tensile tests. The cohesive parameters were found to be essentially rate-independent for the toughened mode, but the toughness dropped by a factor of four upon a transition to the brittle mode. The results of wedge tests were used as an independent verification of the cohesive parameters, and to verify that the quasi-static properties remained rate-independent to very high crack velocities corresponding to conditions of low-velocity impact. The effects of friction, and the use of the wedge test to determine cohesive parameters, were also explored.     

Analytical formulas for the velocity field induced by an infinitely thin vortex ring

Three different analytical solutions are presented for a potential vortex ring using three different streamfunctions. Verification studies confirm that all three approaches are valid. It is found that the solution obtained using the Biot–Savart law is the most efficient method due to its simplicity. It is shown that all analytical results are accurate to within machine accuracy and sample calculations are included. Copyright © 2004 John Wiley & Sons, Ltd.     

Simulation of single‐ and two‐phase flows on sliding unstructured meshes using finite volume method

The paper presents an efficient finite volume method for unstructured grids with rotating sliding parts composed of arbitrary polyhedral elements for both single‐ and two‐phase flows. Mathematical model used in computations is based on the ensemble averaged conservation equations. These equations are solved for each phase and in case of single‐phase flow reduce to the transient Reynolds‐averaged Navier–Stokes (TRANS) equations. Transient flow induced by rotating impellers is thus resolved in time. The use of unstructured grids allows an easy and flexible meshing for the entire flow domain. Polyhedral cell volumes are created on the arbitrary mesh interface placed between rotating and static parts. Cells within the rotating parts move each time step and the new faces are created on the arbitrary interfaces only, while the rest of the domain remain ‘topologically’ unchanged. Implicit discretization scheme allows a wide range of time‐step sizes, which further reduce the computational effort. Special attention is given to the interpolation practices used for the reconstruction of the face quantities. Mass fluxes are recalculated at the beginning of each time step by using an interpolation scheme, which enhances the coupling between the pressure and velocity fields. The model has been implemented into the commercially available CFD code AVL SWIFT (AVL AST, SWIFT Manual 3.1, AVL List GmbH, Graz, Austria, 2002). Single‐phase flow in a mixing vessel stirred by a six‐bladed Rushton‐type turbine and two‐phase flow in aerated stirred vessel with the four‐blade Rushton impeller are simulated. The results are compared with the available experimental data, and good agreement is observed. The proposed algorithm is proved to be both stable and accurate for single‐phase as well as for the two‐phase flows calculations. Copyright 2004 John Wiley & Sons, Ltd.     

Grid‐free surface vorticity method applied to flow induced vibration of flexible cylinders

In order to study cross flow induced vibration of heat exchanger tube bundles, a new fluid–structure interaction model based on surface vorticity method is proposed. With this model, the vibration of a flexible cylinder is simulated at Re=2.67 × 10⁴, the computational results of the cylinder response, the fluid force, the vibration frequency, and the vorticity map are presented. The numerical results reproduce the amplitude‐limiting and non‐linear (lock‐in) characteristics of flow‐induced vibration. The maximum vibration amplitude as well as its corresponding lock‐in frequency is in good agreement with experimental results. The amplitude of vibration can be as high as 0.88D for the case investigated. As vibration amplitude increases, the amplitude of the lift force also increases. With enhancement of vibration amplitude, the vortex pattern in the near wake changes significantly. This fluid–structure interaction model is further applied to simulate flow‐induced vibration of two tandem cylinders and two side‐by‐side cylinders at similar Reynolds number. Promising and reasonable results and predictions are obtained. It is hopeful that with this relatively simple and computer time saving method, flow induced vibration of a large number of flexible tube bundles can be successfully simulated. Copyright © 2004 John Wiley & Sons, Ltd.     

Comments on ‘A New Model for Viscous Dissipation in Porous Media Across a Range of Permeability Values’, Transport in Porous Media 53, 117–122, 2003

Transport in Porous Media -     

Properties of backscattered particles produced by protons of energy above 1 TeV in an iron absorber

Backscattered-particle production is studied by means of a detailed simulation of cascade processes in a dense medium. The energy dependence of the albedo and the spatial and angular distributions of various components of this flux are analyzed.     

Resonant destabilization of phonon microwave stimulated emission in an acoustic quantum oscillator (phaser) with periodically modulated pumping

Two qualitatively different types of resonant destabilization of phonon stimulated emission (SE) are discovered in experiments where a 9-GHz multimode ruby laser is periodically modulated (the electromagnetic pump frequency is 23 GHz). In the case of deep pump modulation at low modulation frequencies (ω=70–200 Hz, where ω_m is the modulation frequency), a fast random alternation of microwave phonon SE modes is observed. This destabilization range corresponds to relaxation resonance in optical lasers. Outside the relaxation resonance range (at ω_m≈10 Hz), the other type of resonant destabilization of stationary phonon SE is observed. This destabilization shows up as very slow regular self-detunings of the microwave SE spectra. The period of such self-organized motions depends significantly on ω_m and changes by several orders of magnitude when ω_m varies within several percent. The second type of SE resonant destabilization is explained in terms of antiphase energy exchange between modes in a modulated phaser.     

Spatial deterministic chaos in optical systems and methods of its modeling

The phenomenon of spatial deterministic chaos is described. A transition from an ordinary differential equation to a discrete map is justified for modeling of the chaos. Methods of studying the chaos dynamics in this model are suggested. It is established how the physical properties of a nonlinear ring interferometer influence the structure of charts of the Lyapunov exponents. The approaches developed in the present study allow an optical cryptosystem to be optimized.__________Translated from Izvestiya Vysshikh Uchebnykh Zavedenii, Fizika, No. 12, pp. 65–71, December, 2004.     

Measurement uncertainty of selenium determination in the reference material Seronorm Trace Elements Serum by hydride generation atomic fluorescence spectrometry

 An analytical result is not considered to be complete without a statement of the measurement uncertainty associated with it. Evaluation of measurement uncertainty is therefore an essential part of every determination. In the present study the measurement uncertainty of the result of determination of selenium in the reference material Seronorm Trace Elements Serum was studied. The combination of a digestion procedure using sulfuric acid, V₂O₅ in H₂SO₄ and hydrogen peroxide and the continuous flow approach of hydride generation atomic fluorescence spectrometry (HG-AFS) detection was used for selenium determination. The total uncertainty budget was calculated with the help of the GUM Workbench program, in which computations follow the rules of the ’ISO guide to the expression of uncertainty in measurement’. The major sources of uncertainty were found to be due to the recovery of the procedure, measurement of peak heights and the purity of Na₂SeO₃. A selenium mass fraction of 77.1±4.8 ng/g (with a coverage factor of 2.1, 95% probability) was determined, which is comparable with the recommended value of 80 ng/g. Received: 13 September 2002 Accepted: 23 December 2002 Acknowledgements We would like to thank Tinkara Buˇcar, B.Sc. for useful discussions and the IAEA Vienna, for financial support of the project 11553/RO. Presented at CERMM-3, Central European Reference Materials and Measurements Conference: The function of reference materials in the measurement process, May 30–June 1, 2002, Rogaška Slatina, Slovenia Correspondence to V. Stibilj